Integral LED ILRC021 User manual

2. PARAMETER
1. INTRODUCTION
IMPORTANT NOTICE
IP20
WARNING
THE WALLMOUNTED TOUCH REMOTE IS A 100240V AC INPUT PRODUCT.
DO NOT INSTALL PRODUCT WITH METAL BOX WHICH CAN AFFECT THE SIGNAL TRANSMISSION.
SWITCH OFF POWER BEFORE CONNECTING THE PRODUCT TO A MAINS SUPPLY.
• Control interface: Touch control
• Input Voltage: 100-240V AC
• Power Consumption: 20mA
• Output: RF signal
• Working Frequency: 868MHz
• For use with ILRC014 RF receiver
• Control: Colour temperature change
• Control Zone: 4 zones synchronously and
independently
• Remote Distance: 20-30 metres
• IP rating: IP20
• Working Temperature: -20°C to 50°C
• Relative Humidity: 8% to 80%
• Product Colour: White (ILRC021)
interface available
• Dimensions: L86×W86×29.1(mm)
• Weight (N.W.): 200g
• This product should be installed according to the instructions
in this guide and by a qualified electrical installer.
• All electrical work must be completed in accordance with the latest
IET wiring regulations (formally IEE) for the UK or in accordance
with all applicable regulations and laws in the country in which it is
being installed.
• Switch OFF power at the mains before installing the product.
• Always disconnect or switch off the power supply before making
any adjustment to the wiring.
• Observe the operating temperature of the product: -20°C to 50°C
• Limited 5 Year Warranty. This LED wall-mounted touch remote is
for indoor use only. Improper installation, abuse or miss-powering
of the wall-mounted touch remote and receiver or failure to
use the wall-mounted touch remote and suitable receiver for its
intended use will void the warranty.Proof of purchase is required
for all returns. Your statutory rights remain unaffected.
Please see www.integral-LED.com/warranty.
Questions? Please contact your supplier or see integral-LED.com
The Integral LED RF colour temperature change wall-mounted touch
remote is designed to work with the Integral LED receiver (ILRC014)
and colour temperature change strip. The wall-mounted touch remote
can be used to control four zones of strip lighting. You will be able to
switch on/o, change the colour temperature of the strip and dim the
strip to your ideal level for each independent lighting zone. You can
change the mood and look of your space instantly.
Integral LED RF Colour Temperature Change
Wall-mounted Touch Remote
ILRC021

3. OPERATING INSTRUCTIONS
Alternative way to match RF receiver when it is dicult to access the receivers.
Switch on the
wall-mounted
touch remote.
Save a scene as
S1 for all zones
Switch ON/OFF
the receiver you’d
like to match for
three times and
switch on.
Press the
“Learning Key”
on RF receiver.
Operating the
touch remote to
select a scene
you like.
Press S1 to recall
the rst scene
setting
Switch on the
wall-mounted
touch remote.
Press a zone number
on the wall-mounted
touch remote from
Z1/Z2/Z3/Z4.
Press a zone number
on the wall-mounted
touch remote from
Z1/Z2/Z3/Z4.
Operating for S2
is the same.
When multiple receivers are matched
to the same zone, repeat the
same setting on the rest of receivers.
Touch the
slider.
Touch the
brightness slider.
LED strip lights
connected
to the RF
receiver ash.
Long press S1 untill the
LED strip light connected
to RF receiver ash.The
scene for all zones is saved.
LED strip lights
connected
to the RF
receiver ash.
The wall-mounted
touch remote and
receiver are matched
and activated.
Operating for
S2 is the same.
The wall-mounted
touch remote and
receiver are matched
and activated.
RECALL the saved scene setting.
One receiver can be matched up to a maximum of 8 wall-mounted touch remotes.
To cancel the matching: Press“Learning Key” button on the receiver for more than 3 seconds until the LED strip lights connected to the receiver flash.
The RF colour temperature change wall-mounted touch remote (ILRC021) is designed to be used with the RF receiver (ILRC014). You will need to match the
receivers before starting to use wall-mounted touch remote.
Match the RF receiver with the“Learning Key” on the receiver(s).
A. Matching the RF Receivers with Colour Temperature Change Wall-mounted Touch Remote
For all operation, first select a zone number from Z1, Z2, Z3 and Z4, then follow the instruction below to activate the selected zone.
ON/OFF INDICATOR: Blue light is ON, Yellow light is OFF (standby).
When Yellow light is on (standby), touch ON/OFF before operating and the indicator will change to Blue light.
ON/OFF: Touch to switch ON/OFF for all zones.
SWITCH :To control SLIDER and toggle between colour temperature or brightness.
SLIDER: Touch to select colour temperature or brightness.
SAVE scene setting. (Saves a scene seeting across all zones)
e.g. S1 to be set as morning mode – white light and 100% brightness. S2 to be set as evening mode – warm light and 100% brightness. Touch S1 to
change all zones to white light and 100% brightness. Touch S2 to change all zones to warm light and 100% brightness.
B. Operating the Wall-mounted Touch Remote

NL
Touch slider to change
COLOUR TEMPERATURE and BRIGHTNESS
AC Mains Power
100-240V AC, 50/60 Hz
(earth is NOT required)
19.4mm
52.0mm 60.3mm
29.1mm 86mm
60.3mm
52.0mm
86mm
Front of the wall-mounted touch remote
Back of the wall-mounted touch remote
Touch to switch ON/OFF
Short press to switch to
control colour temperature
change or brightness
Long press to SAVE,
short press to RECALL
Short press Zone number to set-up
corresponding LED lights, long press
to switch ON/OFF selected zone

Remove the front touch panel with
a suitable at-head screw driver
Pattress/back box with minimum
depth of 25mm
This wall-mounted touch remote requires 100-240V AC 50/60 Hz
mains power and ts a standard single pattress/back box
with minimum depth of 25mm.
Mains power
100-240V AC, 50/60 Hz
(earth is NOT required)
N
L
25mm
C. Installation - Wiring diagram
(Live-Brown)
(Neutral-Blue)
WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF WITH
HOUSEHOLD WASTE. PLEASE RECYCLE WHERE FACILITIES EXIST. CHECK
WITH YOUR LOCAL AUTHORITY FOR RECYCLING ADVICE.
Integral LED is a division
of Integral Memory plc:
Unit 6 Iron Bridge Close,
Iron Bridge Business Park,
London, NW10 0UF, UK