Integral LED ILRC010 User manual

Integral LED RGBW Colour Changing
Remote Control and Receiver ILRC010
IMPORTANT NOTICE
1. Introduction
2. Parameter
IP20
WARNING
DO NOT CONNECT THE RECEIVER TO A MAINS SUPPLY.
THE RECEIVER MUST ONLY BE CONNECTED TO A SUITABLE DC12-24V LED DRIVER.
• This product should be installed according to the instructions in this guide and by a qualied electrical
installer.
• All electrical work must be completed in accordance with the latest IET wiring regulations (formally IEE) for
the UK or in accordance with all applicable regulations and laws in the country in which it is being installed.
• Switch OFF power at the mains before installing the product.
• Always disconnect or switch o the power supply before making any adjustment to the wiring.
• Observe the operating temperature of the product: 0°C to +40°C.
• Limited 3 Year Warranty. This LED Remote control and Receiver is for indoor use only. Improper installation,
abuse or miss-powering of the remote control and receiver or failure to use the remote control and receiver
for its intended use will void the warranty. Proof of purchase is required for all returns. Your statutory rights
remain unaected.
Please see www.integral-LED.com/warranty.
Questions? Please contact you supplier or see www.integral-LED.com
INTRODUCTION
The Integral LED RGBW Colour Changing Remote Control and Receiver is designed to work with the Integral
LED RGBW Colour Strip. You will be able to change the colour of the strip to dierent colour modes changing
the mood and look of your space instantly. You can also dim the strip to your ideal level. The strip can also
switch between dierent colour modes on a continuous basis to add excitement.
Receiver:
• Power Input: DC12V~DC24V
• Max Current Load: Max 20A, 5Ax4CH
• Max Output Power: 240W(12V) / 480W(24V)
• IP Rating: IP20
• Working Temp.: 0ºC~40ºC
• Dimensions: L145×W46.5×H16(mm)
• Weight (N.W.): 110g

Remote:
• Output: RF signal
• Working Voltage: 4.5V
(3 x AAA battery / Not included)
• Working Frequency: 868/915/434MHz
• Remote Distance: 20~30 metres
• IP Rating: IP20
• Working Temp.: 0ºC~40ºC
• Relative humidity: 8%~80%
• Remote Dimensions: L120×W48×H17.6(mm)
• Weight(N.W.): 70g
3. Operating Instruction for Receiver
The Remote control has been matched to the receiver before leaving the factory, if deleted accidentally you
can restore the matching as follows.
RF Code Key: Switch on the remote. And short press the RF Code Key on the receiver, then immediately
touch the colour wheel on the remote. When the LED strips connected to the receiver icker, the remote and
receiver are now matched and activated.
Note: One receiver can be matched to up to 8 remote controls.
Multiple receivers can be matched to one remote.
Cancel the matching: Press RF Code Key on the receiver for more than 3 seconds until the LED strips
connected to the receiver icker.
MASTER/SLAVE jumper:
In a group of multiple receivers, in order to get a good sync of RGB running eect, please set ONLY ONE
receiver as MASTER, the other receivers as SLAVE.
After the Master is set, switch o the Master receiver and then switch on, to activate the Master function.
RF code key: pair with the RF remote
V+ Output (+)
CH 1: R output (-)
CH 2: G output (-)
CH 4: W output (-)
CH 3: B output (-)
DC Power input
MASTER/SLAVE jumper
RF code key
RGBW RF LED Receiver
󴖦
V+
V-
INPU T
V+
R-
G-
B-
OUTPUT
W-
Total Weight (G.W.): 185g

4. Wiring Diagram
Please make sure you connect the strip to receiver correctly, indicated as following table.
4.5V(3xAAA battery, not included)
Back of the remote
RGBW Control
DC 12-24V
DC 12-24V
Receiver to strip
mark on
Receiver
mark on
Strip
V+ V+
R R
G G
B B
W W
5. Operating Instruction for Remote Control
V+ V-
AC Power
50/60Hz
V+
V-
OU TPU T
INP UT
V+ V+
R- R -
G- G -
B- B -
W- W-
V+
V-
IN PU T
V+
R-
G-
B-
OUTPUT
W-
RGBW LED Strip
RGBW RF LED Controller
RF Code Key
12V / 24V
CV PSU
AC INPUT
N
L

Integral LED is a division of Integral Memory plc
London NW10 0UF
Click to turn ON/OFF
Front of the remote
Click to switch on/o
red channel Press and
hold down to increase/
decrease light intensity
Click to switch on/o
green channel Press and
hold down to increase/
decrease light intensity
Switch warm white,
natural white, cool white.
(Through the three RGB
colour mixing)
Colour wheel, touch to
select colour
Click to switch on/o
blue channel Press and
hold down to increase/
decrease light intensity
Click to switch on/o
white channel Press and
hold down to increase/
decrease light intensity
Press and hold down to
save color, click to recall
the saved
Press and hold down
to increase/decrease all
lights intensity
Click to play/pause 10
built-in modes, press
and hold down to speed
up/down the running
mode
LED indicator
R
G
B
W
S2S1