Intel PCM-9587 User manual

PCM-9587
Onboard Intel® Celeron M EBX
SBC with Audio, VGA, LCD,
SATA
Users’ Manual

PCM-9587 User’s Manual ii
Copyright
This document is copyrighted, © 2003. All rights are reserved. The orig-
inal manufacturer reserves the right to make improvements to the prod-
ucts described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmit-
ted in any form or by any means without the prior written permission of
the original manufacturer. Information provided in this manual is
intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the
rights of third parties that may result from such use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
VIA is a trademark of VIA Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
CHRONTEL is a trademark of Chrontel Inc.
All other product names or trademarks are properties of their respective
owners.
For more information on this and our other products, please visit
our website at: http://www.emacinc.com
For technical support and service, please visit our support website at:
http://www.emacinc.com/support
This manual is for the PCM-9587.
Part No. 2006958700
1st Edition, Printed Aug. 2005

iii
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
• 1 PCM-9587 all-in-one single board computer
• 1 CD disk for utility and drivers
• 1 startup manual
• 1 Mini Jumper*10 PCS Package (p/n: 9689000002)
• 1 ATX power cable (p/n:1700001112)
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
Model No. List Description
PCM-9587F-M0A1 Celeron M 600M w/LAN/
Audio/LVDS

PCM-9587 User’s Manual iv
FCC
This device complies with the requirements in part 15 of the
FCC rules: Operation is subject to the following two condi-
tions:
1.This device may not cause harmful interference, and
2. This device must accept any interference received, includ-
ing interference that may cause undesired operation
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio commu-
nications. Operation of this device in a residential area is
likely to cause harmful interference in which case the user will
be required to correct the interference at his/her own
expense. The user is advised that any equipment changes or
modifications not expressly approved by the party responsi-
ble for compliance would void the compliance to FCC regula-
tions and therefore, the user's authority to operate the
equipment.
Caution!
!
There is a danger of a new battery exploding if it is incorrectly
installed. Do not attempt to recharge, force open, or heat the
battery. Replace the battery only with the same or equivalent
type recommended by the manufacturer. Discard used batter-
ies according to the manufacturer’s instructions.

v
Additional Information and Assistance
1. Visit the distrbutator's website at www.emacinc.com where you can
find the latest information about the product.
2. Contact your distributor, sales representative, or customer service
center for technical support if you need additional assistance.
Please have the following information ready before you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages

PCM-9587 User’s Manual vi

vii Table of Contents
Contents
Chapter 1 Introduction......................................................2
1.1 Introduction....................................................................... 2
1.2 Features ............................................................................. 2
1.3 Specifications.................................................................... 3
1.4 Board layout: dimensions.................................................. 5
Figure 1.1:Board layout: dimensions (component side).5
Figure 1.2:Board layout: dimensions (solder side).........6
Chapter 2 Installation........................................................8
2.1 Jumpers.............................................................................. 8
Table 2.1:Jumpers........................................................... 8
2.1.1 Jumpers setting drawing .................................................8
2.2 Connectors....................................................................... 10
Table 2.2:Connectors....................................................10
2.3 Locating jumpers and Connectors................................... 12
Figure 2.1:Jumper & Connector (component side) ......12
Figure 2.2:Jumper & Connector (solder side) .............. 13
2.4 Setting Jumpers............................................................... 14
2.5 Clear CMOS (J3)............................................................. 15
2.6 Installing DIMMs............................................................ 15
2.7 IDE, CDROM hard drive connector (CN15).................. 16
2.7.1 Connecting the hard drive............................................. 16
2.8 Solid State Disk............................................................... 16
2.8.1 CompactFlash (CN30).................................................. 16
2.9 Floppy drive connector (CN14) ...................................... 16
2.9.1 Connecting the floppy drive ......................................... 16
2.10 Parallel port connector (CN16)....................................... 17
2.11 Keyboard and PS/2 mouse connector (CN27) ................ 17
2.12 Front Panel Connector (CN22) ....................................... 18
2.12.1 Power & HDD LED (pin 1-4 of CN22)........................ 18
2.12.2 Reset switch (pin 13-14 of CN22)................................ 18
2.13 Power connectors (CN25,CN5)....................................... 18
2.13.1 ATX power connector, +5V (CN5).............................. 18
2.13.2 CPU Fan power supply connector (CN25)................... 18
2.14 ATX power ON/OFF switch con. pin 11-12 of CN22.... 18
2.14.1 ATX feature (CN5) & soft power switch (CN22)........ 18
2.15 Audio AC'97 Link interfaces (CN4) ............................... 19
2.15.1 Audio connector(CN4) .................................................19
2.15.2 CD audio-in connector (CN3)....................................... 19

PCM-9587 User’s Manual viii
2.16 COM port connector (CN21) .......................................... 19
2.17 VGA/LVDS interface connections (CN7, CN8,CN9).... 19
2.17.1 CRT display connector (CN7)...................................... 19
2.17.2 LVDS LCD panel connector (CN8) ............................. 20
2.17.3 DVI LCD panel connector(CN9).................................. 20
2.18 TV-out interface (CN2).................................................. 21
2.19 Ethernet configuration (CN11)........................................ 21
2.19.1 100Base-T connector (CN11)....................................... 21
2.19.2 Network boot ................................................................ 21
2.20 USB connectors (CN18,CN20)....................................... 21
2.21 LCD Backlight connector (CN1) ....................................22
2.22 SATA Connector (CN23, CN24).................................... 22
2.23 DIO connector (CN19).................................................... 22
2.24 -12V and -5V connector (CN6)....................................... 23
2.25 Extension SMBUS connector (CN26) ............................ 23
2.26 System FAN connector (CN13)...................................... 23
Chapter 3 Software Configuration.................................26
3.1 Introduction..................................................................... 26
3.2 Connections to Three Standard LCDs............................. 27
3.2.1 LG LM150X06 (1024x768(16 colors) LVDS LCD)....27
Chapter 4 Award BIOS Setup.........................................30
4.1 System test and initialization........................................... 30
4.1.1 System configuration verification................................. 30
4.2 Award BIOS setup .......................................................... 31
4.2.1 Entering setup.............................................................. 31
Figure 4.1:BIOS setup program initial screen .............. 31
4.2.2 Standard CMOS Features setup.................................... 32
Figure 4.2:CMOS Features setup.................................. 32
4.2.3 Advanced BIOS Features setup....................................33
Figure 4.3:Advanced BIOS Features setup................... 33
4.2.4 Advanced Chipset Features setup................................. 34
Figure 4.4:Advanced Chipset Features setup ............... 34
4.2.5 Integrated Peripherals ................................................... 34
Figure 4.5:Integrated Peripherals.................................. 34
4.2.6 Power Management Setup ............................................ 35
Figure 4.6:Power Management Setup........................... 35
4.2.7 PnP/PCI Configurations................................................ 35
Figure 4.7:PnP/PCI Configurations.............................. 35
4.2.8 PC Health Status...........................................................36
Figure 4.8:PC Health Status.......................................... 36
4.2.9 Frequency/Voltage Control........................................... 37
Figure 4.9:Frequency/Voltage Control.........................37
4.2.10 Load Optimized Defaults ........................................ 38

ix Table of Contents
Figure 4.10:Load Optimized Defaults ..........................38
4.2.11 Set Password.................................................................38
4.2.12 Save & Exit Setup......................................................... 40
4.2.13 Exit Without Saving...................................................... 40
Chapter 5 PCI Graphic Setup.........................................42
5.1 Introduction..................................................................... 42
5.1.1 Chipset .......................................................................... 42
5.1.2 Display memory............................................................ 42
5.1.3 Display types................................................................. 42
5.1.4 Dual/Simultaneous Display .......................................... 43
5.2 Installation of the PCI Graphic driver............................. 45
5.2.1 Installation for Windows 2000/XP............................... 45
5.3 Further Information......................................................... 48
Chapter 6 Audio Setup.....................................................50
6.1 Introduction..................................................................... 50
6.2 Driver installation............................................................ 50
6.2.1 Before you begin...........................................................50
Chapter 7 PCI Bus Ethernet Interface...........................54
7.1 Introduction..................................................................... 54
7.2 Features ........................................................................... 54
7.3 Installation of Ethernet Driver......................................... 54
7.3.1 Installation for Windows 2000 ..................................... 54
7.4 Further information......................................................... 62
Appendix A Prog. GPIO & W’dog Timer.........................64
A.1 Supported GPIO Register................................................ 64
A.1.1 GPIO Registers............................................................. 64
A.1.2 GPIO Example program-1........................................... 65
A.2 Watchdog programming.................................................. 67
Appendix B Pin Assignments .............................................70
B.1 LCD Backlight Connector (CN1) ......................... 70
B.2 TV Out Connector (CN2) ......................................... 70
B.3 CD-IN Connector (CN3)................................................. 71
B.4 Audio Output Connector (CN4)......................................71
B.5 Power input Connector (CN5)......................................... 72
B.6 -12V and -5V Connector (CN6)...................................... 72
B.7 VGA Connector (CN7) ................................................... 73
B.8 LVDS Connector (CN8) ......................................... 74
B.9 DVI Connector (CN9)..................................................... 75
B.10 Gigabit LAN Connector (CN10 Optional)...................... 75
B.11 10/100M LAN Connector (CN11) .............................. 76
B.12 Gigabit LAN LED Connector (CN12 Optional)............. 76

PCM-9587 User’s Manual x
B.13 System FAN Connector (CN13)..................................... 76
B.14 Floppy Disk Drive Connector (CN14)............................ 77
B.15 Primary HDD Connector (CN15) .................................. 78
B.16 Printer Port Connector (CN16) .................................... 79
B.17 USB Connector (CN18,20) ........................................ 79
B.18 DIO Connector (CN19)................................................... 80
B.19 COM Port Connector (CN21) ................................... 81
B.20 Front Panel Connector (CN22) .............................. 82
B.21 SATA Connector 1 (CN23)............................................. 82
B.22 SATA Connector 2 (CN24)............................................. 83
B.23 CPU FAN Connector (CN25) ....................................... 83
B.24 Extension SMBUS Connector (CN26) ........................... 83
B.25 Keyboard and PS/2 Mouse Connector (CN27) ............. 84
B.26 CPU FAN Connector (wafer box)(Optional)(CN28) .... 84
B.27 Mini PCI Connector(CN29)............................................ 85
B.28 CompactFlash Card Connector (CN30) ..................... 86
Appendix C System Assignments......................................88
C.1 System I/O Ports.............................................................. 88
Table C.1:System I/O Ports .......................................... 88
C.2 1st MB memory map....................................................... 89
Table C.2:1st MB memory map ................................... 89
C.3 DMA channel assignments.............................................. 89
Table C.3:DMA channel assignments .......................... 89
C.4 Interrupt assignments ...................................................... 90
Table C.4:Interrupt assignments................................... 90
Appendix D Optional Extras ..............................................92
D.1 PCM-10586-6200 Cable kit for PCM-9587................... 92
Table D.1:PCM-10586-6200 wiring kit 9587...............92
D.2 ATX Power Control Cable (CN15)................................. 92
Appendix E Mechanical Drawings.....................................94
Figure E.1:PCM-9587 Mechanical Drawing (component
side)94
Figure E.2:PCM-9587 Mechanical Drawing (solder side)
95

1 Chapter1
CHAPTER
1
General Information
This chapter gives background
information on the PCM-9587.
Sections include:
• Introduction
• Features
• Specifications
• Board layout and dimensions

PCM-9587 User’s Manual 2
Chapter 1 Introduction
1.1 Introduction
The PCM-9587 series is a 5.25” SBC (Single Board Computer) designed
with the powerful Intel Celeron M processor, and Intel 852GM and
6300ESB chipsets, which supports Dynamic Video Memory Technology
For maximum performance. PCM-9587 also supports one 184 PIN
DIMM socket for ECC DDR memory up to 1GB. These chipsets are spe-
cifically for embedded computing and provide an optimized on-board
integrated graphics solution.
Other on-board features include 1 EIDE, 2 SATAs, 1 FDD, 1 LPT, 4
USB2.0s, 4 serial ports(3 x RS-232 and 1 x RS-232/422/485), PS/2 Key-
Board/mouse, watchdog. The SSD solution supports Type I/II Compact-
Flash cards.
The PCM-9587 complies with EBX form factor (Embedded Board
eXpandable). It is small enough for embedded applications, yet large
enough to contain the functions of a full embedded computer system. The
EBX system expansion is based on popular existing industry standards-
PC/104TM, PCI, and PC/104-PlusTM, hence the PC/104-Plus interface on
PCM-9587 brings the advantages of a wide variety of embedded system
expansion modules. The expandability can also be fulfilled by the
MiniPCI socket on the solder side.
1.2 Features
• Embedded Intel Celeron M 600 MHz
• Supports ECC DDR Memory
• Applied EBX form factor standard and support for PC/104-Plus bus
• Supports up to 10/100Base-T Ethernet
• Supports 4 port Host USB2.0
• Supports up to 2 channel 48-bit LVDS interface

3 Chapter1
1.3 Specifications
Standard SBC Functions
• CPU: Supports onboard Celeron® M
• BIOS: Award 512K byte Flash memory
• System memory: One 184 pin DIMM sockets, support ECC
Double Data Rate (DDR)128 MB to 1 GB, accepts 128/256/512/1000
MB DDR200/266 DRAM.
• System chipset:Intel 852GM GMCH/6300ESB Chipset 400MHz FSB
• Enhanced IDE interface: One Enhanced IDE interface supports 2 IDE
devices. PIO mode 3 or mode 4, Ultra DMA 100 transfer. 2 Serial
ATA standard connector to support SATA 150
• FDD interface: Supports one FDD
• Serial ports: Three serial RS-232 ports, one serial RS-232/422/485
ports
• Parallel port: One parallel port, supports SPP/EPP/ECP mode
• Keyboard/mouse connector: Supports standard PS/2 keyboard and a
PS/2 mouse
• Power management: APM Rev. 1.2 compliant power management
ACPI support
• Watchdog timer: Winbond W83627, 255 levels timer interval, setup
by software
• USB: Four USB 2.0 compliant host ports
• IrDA: N/A
• GPIO: 8-bit general purpose input/output
• Expansion: PC/104(LPC), PC/104+, PCI and miniPCI
Solid State Disk
• Supports one 50-pin socket for CFC type I/II
VGA/LCD Interface
• Chipset: Intel Montara-GM/GM+ GMCH
• Frame buffer: Optimized Shared Memory Architecture, supports up to
64MB frame buffer using system memory

PCM-9587 User’s Manual 4
• Interface: 4x AGP VGA/LVDS interface
• Display mode: CRT Modes: pixel resolution up to 1600 x 1200 at 85-
Hz and 2048 x 1536 at 75-Hz
• LCD mode: Dual channel LVDS panel support up to UXGA panel res-
olution with frequency range from 25-MHz to 112-MHz
• LVDS: Supports 2 channel (48-bit) LVDS LCD panel
TV-Out/DVI
• Chipset: Chrontel CH7009
• Supports composite, s-video or RGB output
• Supports NTSC and PAL formats
Ethernet interface
• Chipset:
• Intel 82551ER /82551QM optional
• Ethernet interface:
• IEEE 802.3u 100 BASE-T Fast Ethernet compatible (PCM-9587)
• I/O address switchless setting
• Built-in boot ROM
Audio Function
• Chipset: 6300ESB, Audio codec ALC 202
• Audio controller: AC’97 3D surround stereo sound
• Supports Speaker out, CD-input, Line-in, Line-out, Microphone
Mechanical and Environmental
• Dimensions: (L x W)203 x 146 mm (8" x 5.75")
• Power supply Voltage:ATX, with Vcore 2 phase, +5V power only can
work
• Power Requirement: (Celeron M 600 with 256MB)
Max: 2.63A@ 5V, 0.03A @ 12V
Typical: 2.62A@ 5V, 0.03A @ 12V

5 Chapter1
• Operating temperature:0 ~ 60° C (32~140° F)
• Operating Humidity:0% ~ 90% Relative Humidity, non-condensing
• Weight: 0.85 kg (weight of total package)
1.4 Board layout: dimensions
Figure 1.1: Board layout: dimensions (component side)

PCM-9587 User’s Manual 6
Figure 1.2: Board layout: dimensions (solder side)

7 Chapter2
CHAPTER
2
Installation
This chapter explains the setup proce-
dures of PCM-9587 hardware, includ-
ing instructions on setting jumpers and
connecting peripherals, switches and
indicators. Be sure to read all safety
precautions before you begin the instal-
lation procedure.

PCM-9587 User’s Manual 8
Chapter 2 Installation
2.1 Jumpers
The PCM-9587 has a number of jumpers that allow you to configure your
system to suit your application. The table below lists the functions of the
various jumpers.
2.1.1 Jumpers setting drawing
Table 2.1: Jumpers
Label Function
J1 LCD Voltage Select
J2 PC104+ VIO Select
J3 Clear CMOS function Select
J5 COM2 RS232/422/485 function Select
J1: LCD Voltage Select
PIN FUNCTION
1-2 VCC3*
2-3 VCC
J2: PC104+ VIO Select
PIN FUNCTION
1-2 VCC*
2-3 VCC3
123 123
123 123

9 Chapter2
J3: Clear CMOS function Select
PIN FUNCTION
1-2 Open Normal*
1-2 Close Clear CMOS
J5: COM2 RS 232/422/485 Select
PINS RS-232 RS-422 RS-485
1,2 Open Open Close
3,4 Open Close Open
5,6 Close Open Open
7,9 Close Open Open
8,10 Close Open Open
9,11 Open Close Close
10,12 Open Close Close
13,15 Close Open Open
14,16 Close Open Open
15,17 Open Close Close
16,18 Open Close Close
RS-232
12
2 .. .. .. .. .. .. .. 18
○ ○ ■■ ○■■ ○
□ ○
■
■■■ ○■■ ○
1 .. .. .. .. .. .. .. 17

PCM-9587 User’s Manual 10
2.2 Connectors
On-board connectors link the PCM-9587 to external devices such as hard
disk drives, a keyboard, or floppy drives. The table below lists the func-
tion of each of the board’s connectors.
RS-422
RS-485
Table 2.2: Connectors
Label Function
CN1 LCD Backlight connector
CN2 TV-out connector
CN3 CD-IN connector
CN4 Audio output connector
CN5 Power input connector
CN6 -12V and -5V connector
CN7 VGA connector
CN8 LVDS connector
CN9 DVI connector
CN10 Gigabit LAN connector(Optional)
CN11 10/100M LAN connector
CN12 Gigabit LAN led connector(Optional)
2..............18
○ ○ ○ ■■ ○■■
□
■
■○ ○ ■■ ○■■
1..............17
2 .. .. .. .. .. .. .. 18
○○○■■ ○■■
■
■○○○■■ ○■■
117