Intel P4304BT series User manual

Thank you for buying an Intel® Server Chassis or System. The following information
will help you assemble your Intel®Server Chassis and install components.
If you are not familiar with ESD [Electrostatic Discharge] procedures used during
system integration, see the complete ESD procedures described in your Service Guide.
This guide and other supporting documents are located on the web at:
http://www.intel.com/support.
G23642-001
Intel® Server Chassis P4000S Family
Intel® Server System P4304BT Series
Quick Installation User's Guide

Intel® Server Chassis P4000S Family Product Configuration
= Configuration Feature
4 x 3.5"
Fixed
4 x 3.5"
Hot Swap
Hard Drive
System Fan
Rear Fan
(92x38mm)
365W
Fixed
Power Supply
P4304XXSFCN
P4304XXSHCN
Intel® Server System
Intel® Server Chassis P4000S Family Supported Board and Integrated System
Warning
Read all caution and safety
statements in this document
before performing any of the
instructions. Also see the Intel
®
Server Board and Server Chassis
Safety Information document at:
http://support.intel.com/support/
motherboards/server/sb/cs-010770
.htm for complete safety information.
Warning
Installation and service of
this product to be performed
only by qualified service
personnel to avoid risk of injury from
electrical shock or energy hazard.
Caution
Observe normal ESD
[Electrostatic Discharge]
procedures during system
integration to avoid possible
damage to server board and/or
other components.
Tools Required
Anti-static
wrist strap
Phillips*
screwdriver
Flat Blade
screwdriver
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other
names and brands may be claimed as the property of others. Copyright © 2011, Intel Corporation. All rights reserved.
Integrated Intel® Server System
Intel® Server Chassis Supported Intel® Server Board
P4304XXSFCN
P4304XXSHCN
P4304BTLSFCN
P4304BTSSFCN
P4304BTLSHCN
S1200BTL
S1200BTL
S1200BTS

Table of Contents
Fixed Hard Drive Installation ........................................................................................ 7
Hot-Swap Hard Drive Installation .............................................................................. 7
Intel® Server Chassis P4304XXSFCN ...................................................................... 1
Intel® Server Chassis P4304XXSHCN ..................................................................... 1
Intel® Server Board S1200BTL ................................................................................... 8
Intel® Server Board S1200BTS ................................................................................ 10
General Installation Process ........................................................................................................ 2
Hard Drive Installation .................................................................................................................... 7
Intel® Server Board S1200BT series ....................................................................... 5
Processor, Heat Sink, Memory Installation .......................................................................... 5
Servel Board Cabling Connections ........................................................................................... 8
Front Panel Controls and Indicators ..................................................................................... 11
Chassis Overview .............................................................................................................................. 1

Chassis Overview
Chassis Features and Components
365-W Fixed Power Supply
I/O Ports
Alternate Serial Port Knockout
PCI Add-in Board Slot Covers
AC Input Power Connector
92mm Chassis Rear Fan
Alternate RMM4 Knockout
A Kensington* Cable Lock Mounting Hole
Padlock Loop
Alternate RMM4 Knockout
Front Control Panel
5.25" Peripheral Bays
Hard Drive Bays
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
J
JK
K
L
L
M
M
Chassis Features and Components
365-W Fixed Power Supply
I/O Ports
Alternate Serial Port Knockout
PCI Add-in Board Slot Covers
AC Input Power Connector
92mm Chassis Rear Fan
Alternate RMM4 Knockout
A Kensington* Cable Lock Mounting Hole
Padlock Loop
Alternate RMM4 Knockout
Front Control Panel
5.25" Peripheral Bays
4 x 3.5" Hot-swap HDD Cage
A
AB
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
J
JK
K
L
L
M
M
1
Intel® Server Chassis P4304XXSHCN
Intel® Server Chassis P4304XXSFCN

2
3Remove the Bezel Assembly
A
B
A
A
B
B
At a 40-degree angle, push the bezel
assembly away from the chassis.
Release the two plastic tabs on the left side
of the bezel assembly to disengage the
tabs, and rotate the bezel assembly no
more than 40 degrees outward.
CAUTION: Do not rotate the bezel
assembly more than 40° or you will
damage the bezel hooks at the
right side of the bezel assembly.
4Install Hard
Drive
See Hard Drive Installation
Section
(Page 7 ) for your
Hard Drive Installation.
5Install Tool-less CD-ROM or DVD-ROM Drive
A
AB
Attach slides to the DVD or CD-ROM drive by pressing
the slides firmly into the side dimples on the DVD or
CD-ROM drive.
Remove an EMI shield.
C
Insert the drive/slide assembly into the
device bay until the slides lock into place.
C
B
B
General Installation Process
Remove the Side Cover
B
Remove the screws.
A
Note:
A non-skid surface or
a stop behind the
chassis may be
needed to prevent the
chassis from sliding
on your work surface.
Slide the side cover
back and lift the cover
outward to remove it.
A
A
B
1
The installation instructions in this section are for general components of Intel® Server Chassis
P4000S family, but the illustrations are based on the Intel® Server Chassis P4304XXSFCN.
2Install Server Board
• If the server board is pre-installed, please follow the
instructions in Processor, Heat Sink, Memory
Installation section ( Page 5 ) to install the
Processor(s), Heat Sink(s) and Memory.
Return to this section when finished.
• If the server board is to be installed, please use the
bumpers, standoffs and mounting screws that
came with your chassis, and open the Intel®Server
Board box, then follow the instructions in the enclosed
Intel®Server Board Quick Start User’s Guide for
server board installation and back panel I/O shield
installation.
Return to this section when finished.

3
General Installation Process
Install PCI Card Assembly ... Continued
From inside of
chassis,press open
the back panel PCI
add-in board
retention device.
B
B
6Install PCI Card Assembly
A
B
Insert tabs on left side of PCI
Card Guide into slots in
chassis.
Secure the PCI Card Guide
with the screws .
A
B
NOTE: Only needed when full
length PCI card is plugged.
A. Install PCI Card Guide B. Install PCI Add-in Boards
ARemove the PCI
slot shield by
pushing the shield
out from inside
the chassis.
A
CWhile holding the
PCI add-in board by
its top edge or upper
corners, firmly press
the add-in board into
the expansion slot.
DClose the PCI
add-in board
retention device.
D
C
7Complete Server Board Cabling
Connections
See your Intel®Server Board Quick Start User's Guide
or Service Guide for server board cable connections.
See Platform Cabling diagram in Server Board Cabling
Connections section ( Page 8-10 ) for your server board
to chassis cable connections.
Return to this section when finished .
8Remove Filler Panels
Remove the bezel filler panels for
each drive you have installed.
Release plastic tabs located at back
side of bezel and pull out filler
panels from front.

4
General Installation Process
9Install Front Bezel Assembly
A
B
Engage three plastic bezel hooks into the raised metal
slots at the chassis edge. Keep the right edge of front
bezel align tightly with the right edge of the Chassis.
Rotate the bezel assembly toward the chassis and latch
the two plastic tabs on the left side of the bezel
assembly to the chassis.
A
A
A
B
B
10 Install Side Cover
B
ASlide the chassis cover on the chassis.
Secure the chassis cover with the screws .
CAUTION: This chassis must be operated with the
SIDE COVERS installed to ensure proper cooling.
B
B
A
11 Finishing Up
2. Connect the AC
power cable last.
1. See your Intel®
Server Board
Quick Start User's
Guide to connect
your keyboard,
mouse, video, and
other I/O cables.
I/O Connections
AC
Power
CAUTION:
power supply
requires a
16-gauge
power cord.
12 Install Software
• BIOS, Drivers, and Operating System Install
A. Confirm BIOS Version: Look on the Server/System
Management screen in the BIOS Setup Utility to determine the
installed BIOS version.
Compare this to the versions at:
http://www.intel.com/support
If new versions are available, update the BIOS on your server.
See the User Guide on the Intel®Server Deployment Toolkit CD
for update instructions.
B. Configure your RAID Controller: Use the instructions
provided with the RAID controller.
C. Install your Operating System: Use the instructions
provided with the RAID controller and with the operating system.
D. Install Operating System Drivers: With the
operating system running, insert the Intel®Server Deployment
Toolkit CD. If using a Microsoft* Windows* operating system,
the Express Installer will autorun and allow you to select the
appropriate drivers to install. On other operating systems,
browse the CD folders to locate and install the driver files.

5
Intel® Server Board S1200BT Series
2a
A. Open the Socket Lever
Push the lever handle down
and away from the socket to
release it.
Rotate the lever all
the way to open.
B. Open the Load Plate
C. Disengage the Cover
Open the
load
plate as
shown.
A
A
B
B
D. Remove the Cover
E. Unpack the Processor
Save the
protective
cover.
Carefully lift the cover
straight up as shown.
REMOVE
1
REMOVE
REMOVE
REMOVE
Place thumb and finger as
shown and tilt up slightly at front.
A
REMOVE
C
Carefully remove
protective cover
as shown.
Save the
protective
cover.
B
Install the Processor(s)
Cautions:
When removing the protective
cover, DO NOT TOUCH the
gold socket pins.
A
When unpacking a processor,
hold by the edges only to avoid
touching the gold contact pins.
C
To avoid damage, DO NOT
DROP the cover onto the
socket pins or components.
B
Follow below Instructions for step on page 2 , then return to step on page 2 when finish this section.
23
Processor, Heat Sink, Memory Installation
Install the Processor(s) ... continued
H. Engage the Load Plate
A
B
Push down on the locking lever.
I. Latch the Locking Lever
A
Slide the tip of the lever under the
notch in the load plate. Make sure
the lever is securely latched.
B
B
A
Load Plate
Front Edge
Shoulder
Screw
A
B
CAUTION: DO NOT damage the
server board with the tip of the
locking lever.
Make sure the front edge of the load
plate slides under the shoulder screw
as the lever is lowered.
Close the load plate
locking lever.
F. Install the Processor
Processor must align correctly with
the socket opening before installation.
DO NOT DROP processor into socket!
CAUTION: The underside of
the processor has components
that may damage the socket pins if
installed improperly.
Components
Orient the processor with the socket so that the processor
cutouts match the two
socket pins.
A
Note location
of gold key at
corner of
processor.
B
A
B
Install the Processor(s) ... continued
G. Close the Load Plate
Carefully lower the load plate over the processor.

6
Processor, Heat Sink, Memory Installation
2b Install Active Heat Sink(s)
A
Align heat sink with holes
in board and lower assembly
to board. Snaps go through
holes in server board.
B
Press downward
on top of cap.
C
Plug the fan cable into the CPU fan header.
E
Fastener snaps
into final position.
D
Repeat B-D for each
fastener in the numerical
order shown at left.
Note: Heatsink
styles may vary
2
3
1
4
TIM
A
E
Make sure the screwdriver slot at
the top of each fastener is rotated
perpendicular to the blades of
the heat sink as shown.
Use the following procedure to install an
active heat sink to your server board:
CAUTION: The heat sink has
thermal interface material (TIM)
on the underside of it. Use
caution so that you do not
damage the thermal interface
material. Use gloves to avoid
sharp edges.
2c Install DIMM Memory Modules To Install DIMMs:
DDR3 DIMM Memory Identification:
Open both DIMM socket levers.
C
A
D
E
Note location of alignment notch.
B
DIMM
notch and
socket
bump must
align as
shown.
Other
Memory
DDR3
This server board supports up to 4 DDR3 1066/1333 ECC UDIMM.
Non-ECC memory is NOT supported by this server board.
CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures
to avoid possible damage to system components.
A
C
DB
E
Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot.
Push down firmly on the DIMM until it snaps into place and both levers close.
IMPORTANT! Visually check that each latch is fully closed and correctly engaged with
each DIMM edge slot.
CAUTION: Avoid touching contacts when handling or installing DIMMs.
Install DIMM Memory Modules ... Continued
Memory Configurations and Population Order:
Note: For additional memory configurations, see
the Techinical Product Specification on the Intel®
Server Deployment Toolkit CD that accompanied
your Intel®Server Board S1200BT, or go to:
http://www.intel.com/support/motherboards/server.
Memory sizing and configuration is supported
only for qualified DIMMs approved by Intel®. For
a list of supported memory, see the tested memory
list at
http://serverconfigurator.intel.com/default.aspx.
DIMM A2
DIMM A1
DIMM B2
DIMM B1
Memory Type: Minimum of one 1 GB, DDR3
1066/1333 MHz ECC UDIMM.
DIMM A2
DIMM A1
DIMM B2
DIMM B1
Intel ®Server Board S1200BTL Shown Intel ®Server Board S1200BTS Shown
NOTE: Return to step on page 2 when finish this section.
3

7
Hard Drive Installation
A
B
A
B
Lift the EMI shield.
move EMI shield
outward from the
chassis.
B. Install the Hard Drive C. Install the EMI shield
AB
Secure the HDD on the
HDD carrier tray with
screws.
Pull out the HDD
carrier tray.
C
Insert the HDD carrier
tray into chassis.
A
B
C
CAUTION: HDDs should be placed evenly in the slots, an empty slot
is needed between every two HDDs.
A
B
While pressing the EMI Shield,
slide the EMI Shield downwards
until the latches on the EMI Shield
are engaged with the chassis.
Fit the edges of the EMI Shield
against the sides of the chassis.
B
AA
A. Remove the EMI
shield
Fixed Hard Drive Installation
Hot-Swap Hard Drive Installation
A
Remove the drive carrier
by pressing the green
button and opening the
lever. Then slide the
carrier out.
B
Remove the four screws
securing the 2.5" HDD
interface bracket and
remove the 2.5" HDD
interface bracket.
C
Install the hard
disk drive using
the same four
screws as shown.
Make sure the
connector end of
the drive matches
the backplane
connector.
D
E
With the lever open, insert
the hard disk drive
assembly into the cage
opening and push until the
locking lever engages.
Push in the lever to
lock it into place.
A
TOP
BREAK OFF TAB
BEFORE MOUTING
2.5´´ HARD DRIVE
B
E
D
C
3.5´´ HDD
4
4
NOTE: Return to step on page 2 when finish this section.
5
Follow below Instructions for step on page 2 , then return to step on page 2 when finish this section.
45

8
Server Board Cabling Connections
Intel® Server Board S1200BTL
Intel® Server Board S1200BTL To Intel® Server Chassis P4304XXSFCN
DIMM_A2
DIMM_A1 DIMM_B2
DIMM_B1
Serial B
Port
Internal
USB
Internal
USB
SATA 5
SATA 2
SATA 1SATA 0
USB
Floppy Front Panel
Connector
SATA 4SATA 3
IPMB
SAS Module
Internal USB SSD
SGPIO
Processor
RMM NIC
Main Power Connector
P/S AUX
CPU Power
Connector
NIC2
USB2
USB3
NIC1
USB0
USB1
Serial Port A
Video
LEDs
SYS
FAN 4
HSBP
Slot 1 ( PCI )
Slot 3 ( PCIe
x
4 )
Slot 4 ( PCIe
x
4 )
Slot 5 ( PCIe
x
4 )
Slot 6 ( PCIe
x
8 ) LP Riser
SYS
FAN 3
SYS
FAN 2
SYS
FAN 1
CPU
FAN
365W Fixed
Power Supply
Module
HDD HDD HDD HDD
ODD ODD
Rear
Fan
Ext
USB
Common FP
Intrusion
Switch
CPU Fan
NOTE : The Chassis mechanically supports up to three
5.25" ODDs.
7
NOTE: Return to step on page 3 when finish this section.
8
Follow below Instructions for step on page 3 , then return to step on page 3 when finish this section.
78

9
Server Board Cabling Connections
Intel® Server Board S1200BTL
DIMM_A2
DIMM_A1 DIMM_B2
DIMM_B1
Serial B
Port
Internal
USB
Internal
USB
SATA 5
SATA 2
SATA 1SATA 0
USB
Floppy Front Panel
Connector
SATA 4SATA 3
IPMB
SAS Module
Internal USB SSD
SGPIO
Processor
RMM NIC
Main Power Connector
P/S AUX
CPU Power
Connector
NIC2
USB2
USB3
NIC1
USB0
USB1
Serial Port A
Video
LEDs
SYS
FAN 4
HSBP
Slot 1 ( PCI )
Slot 3 ( PCIe
x
4 )
Slot 4 ( PCIe
x
4 )
Slot 5 ( PCIe
x
4 )
Slot 6 ( PCIe
x
8 ) LP Riser
SYS
FAN 3
SYS
FAN 2
SYS
FAN 1
CPU
FAN
365W Fixed
Power Supply
Module
HDD_0 HDD_1 HDD_2 HDD_3
ODD ODD
Rear
Fan
Ext
USB
Common FP
4x3.5"
Hot-Swap
BackPlane SGPIO I2C_OUT
I2C_IN
PowerPower
Intrusion
Switch
1
2
3
J4P2
SATA 6X mode
jumper (J4P2)
should at Pin
1-2 for Intel®
Server Board
S1200BTL
CPU Fan
Intel® Server Board S1200BTL To Intel® Server Chassis P4304XXSHCN
7
NOTE : The Chassis mechanically supports up to
three 5.25" ODDs.
NOTE: Return to step on page 3 when finish this section.
8
Follow below Instructions for step on page 3 , then return to step on page 3 when finish this section.
78

10
Server Board Cabling Connections
Intel® Server Board S1200BTS
7Intel® Server Board S1200BTS To Intel® Server Chassis P4304XXSFCN
NIC1
USB0
USB1
NIC2
USB2
USB3
Video Serial Port A
LEDs
CPU Power
Connector
SYS
FAN 2
DIMM_A2
DIMM_A1 DIMM_B2
DIMM_B1
Main Power Connector
SYS
FAN 1
SYS
FAN 3
CPU
FAN
Processor
Slot 4 ( PCI )
Slot 7 ( PCIe
x
8 )
Slot 5 ( PCIe
x
4 )
Slot 6 ( PCIe
x
8 ) LP Riser
SGPIO
SATA 0 SATA 1
SATA 2
SATA 5 SATA 4
SATA 3
USB 6 USB 4-5 Front Panel
Connector
CPU Fan
365W Fixed
Power Supply
Module
HDD HDD HDD HDD
ODD
Rear
Fan
Ext
USB
Common FP
Intrusion
Switch
NOTE : The Chassis mechanically supports up to three
5.25" ODDs.
NOTE: Return to step on page 3 when finish this section.
8
Follow below Instructions for step on page 3 , then return to step on page 3 when finish this section.
78

11
Front Panel Controls and Indicators
Front Panel Controls and Indicators
A
A
B
B
C
C
D
D
E F G
E
H
I
F
G
H
I
ID Button with ID LED Integrated
USB Connectors
Reservation(Optional VGA/Serial Port)
System Reset Button
NIC LED System Power Button with Power LED
HDD Activity LED
System Status LEDNMI Button

G23642-001