Intelix INT-HDX100-RXWP User manual

11675 Ridgeline Drive
Colorado Springs, CO
80921
Rev 190306 Phone: [phone]
Toll-Free: 800-530-8998
Fax: [phone]
INT-HDX100-RXWP Quick Install Guide
This guide is for quick installaon only.
For complete owners manual go to www.libav.com or use a QR reader to access the
manual via QR code below.
Scan QR Code with your Smart-phone or Tablet

INT-HDX100-RXWP Quick Guide
3
The Intelix INT-HDX100-RXWP receives HDMI, IR, Ethernet and RS232 over a single solid core shielded
Category cable. The INT-HDX100-RXWP supports 1080p video signal up to 100m and 4K signals up
to 4K@60Hz / 4:2:0 / 8 bit color up to 70m. The INT-HDX100-RXWP supports CEC pass through and
is HDCP 2.2 compliant. 48V PoH built in allows the receiver to be powered from a compable Intelix
transmier.
The INT-HDX100-RXWP is compable with all Intelix HDBaseT product oerings and any product that
meets the HDBaseT specicaons.
Product Overview
Package Contents
• INT-HDX100-RXWP HDBaseT Wall Plate Transmier
• Quick Install Guide
• 2 gang decorator plate cover
• RS232 to DB9 breakout cable
• 2-pin phoenix connector
• (4) Mounng Screws
• 24V DC Power supply with US, EU, UK and AU power adapters.

INT-HDX100-RXWP Quick Guide
4
Receiver View
FRONT BACK
15
6
7
3
8
9
4
2
1. DIAGNOSTIC LED’S
POWER (RED) - Solid when device is powered ON
LINK (GREEN) - Solid when successful link between transmier and
receiver is established; o or blinking indicates a physical link error
HDCP (GREEN) - Solid when HDMI signal is encrypted; blinking when
non -HDCP protected content is transmied; OFF when no content is
being transmied
2. IR IN -3.5mm connecon for IR receiver
3. IR OUT -3.5mm connecon for IR emier
4. HDMI OUT - HDMI output port for connecon to HDMI display
5. ETHERNET - RJ45 port for passing Ethernet to receiver / display locaon from transmier /
source locaon
6. RS232 - 3 pin terminal block for RS232 pass through control of connected display or 3rd party
device
7. DC24V - DC connector for power supply
8. HDBT IN / POH IN - HDBaseT input; RJ45 connecon. Supports 48V PoH

INT-HDX100-RXWP Quick Guide
5
Connecvity Instrucons
1. Verify all components included with the extender set are present before installaon.
2. Turn o power and disconnect the audio/video equipment by following the manufacturer’s
instrucons.
3. Connect Category 6 or greater twisted pair cable with RJ45 connectors between the
INT-HDX100-RXWP and a compable Intelix HDBaseT transmier. TIA/EIA-568B straight-through wiring
connecons must be used with all HDBaseT extenders.
4. Connect an HDMI cable and any desired IR, Ethernet and RS232 connecons between the display
and the INT-HDX100-RXWP.
5. Connect an HDMI cable and any desired IR, Ethernet and RS232 connecons between the source
and a compable Intelix HDBaseT transmier.
6. Connect a power supply to the compable Intelix HDBaseT transmier. and lock the power supply
to the power connector by twisng the locking collar clockwise.
7. Power on aached audio/video devices.
Passing IR Signals:
The INT-HDX100-RXWP is capable of passing IR signals between 30 and 50 KHz. To
prevent damage to any of the electronics, the extender should be powered o while
inserng or removing any IR components. Inserng an IR transmier into the IR IN
port may damage the IR circuit for that extender.

INT-HDX100-RXWP Quick Guide
6
Cabling Wiring Requirements
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category 6
connecon between send and receive
units.
HDBaseT Cabling
To ensure proper performance of the INT-HDX100-RXWP, it is recommended that you
use solid core, shielded Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may
perform well but may not support power over HDBaseT reliably over longer distances.
For opmized HDBaseT performance use the following Liberty Wire and Cable branded
cabling;
Category 6 plenum; 24-4P-P-L6SH
Category 6A plenum; 24-4P-P-L6ASH
Category 6 NON-plenum; 24-4P-L6SH
Category 6A NON -plenum; 24-4P-L6ASH
When using shielded category cabling ALWAYS...
....use shielded connectors
....properly ground the category cable

INT-HDX100-RXWP Quick Guide
7
Technical Specicaons
Supported Audio and Video
Video Compliance HDMI 2.0+, HDCP2.2, and CEC (Consumer Electronics Control)
Input / Output Resoluon Support Up to 4096x2160@60Hz (4:2:0 chroma sub-sampling / 8 bit deep color)
Embedded Audio Up to PCM 8 channel, Dolby Digital, DTS, TrueHD, DTS-HD Master Audio and
Dolby Atmos
IR Carrier Frequency Range 30-50kHz at 5 volts
HDBaseT Signal Characteriscs
Maximum Distance 1080p: 100 meters / 330 feet
4K@60Hz 4:2:0 70 meters / 230 feet
Cable Requirements Solid core shielded Category 6 F/UTP or greater with TIA/EIA-568B crimp
paern
Bandwidth 10.2 Gbps
Chassis and Environmental
Dimensions (H x W x D) 104.5mm x 89.0mm x 67.9mm (4.1” x 3.5” x 2.7”)
Product Weight 285g / 0.6lbs
Operang Temperature -5° to +55° C (+23° to +131° F)
Storage Temperature -20°C to 70°C (-4°F to 158°F)
Operang Humidity (Environment) 10% to 90%, Non-condensing
ESD Protecon Human-body Model:
±8kV (Air-gap discharge)
±4kV (Contact discharge
Surge Protecon Voltage: ±1 kV
Power
Maximum Power Consumpon 9 was
Power Supply Input Voltage 100-240V AC at 50-60 Hz
Power Supply Output Voltage 24V DC
Regulatory CE, FCC, RoHS
Other
Standard Warranty 5 Years
Included Items Quick Guide, 2 gang decorator plate cover, RS232 to DP9 breakout cable, 2-pin
phoenix connector, 4 mounngs screws and a 24V DC power supply with US,
EU, UK and AU adapters.
Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and
electrical interference, and cable patches.

Thank you for your purchase.
For Technical Support please call our toll free number at
800-530-8998 or email us at [e-mail]
www.libav.com
Intelix is a brand of:
11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: [phone]
Fax: [phone]
Toll-Free: 800-530-8998