Intelligent Glass Switchable Film User manual

Switchable Film
Installation Guide

2
‘© Copyright Pro Display 2009’
Equipment Required
- Self adhesive Switchable Film
- Window scraper / blade
- Hard rubber roller
- Soft edge squeegee
- Nitrile protective gloves
- Cleaning cloths
- Liquid glass polish
- IPA / Soft cloths
- 1.5mm electrical cable
- Cable strippers
- Soldering iron / solder
- Scissors / sharp blade
- Dow Corning silicone (7091)
- Plastic cover trim / clear double sided tape
PLEASE NOTE
- Switchable Film is a dry install application. Please do NOT use water under any circumstances other than
for cleaning the glass.
- We recommend the outer dimensions of the self adhesive Switchable film are 2 - 3mm shorter than the
visual area of the glass.
- The bus bar (electrical contact strip) should never come into contact with any metal frame / trim.
Preparation is the key to a successful install.

3
‘© Copyright Pro Display 2009’
Step 1
Place the film in a safe clean place, preferably on a table.
Step 2
Make sure the cling surface is facing up.

4
‘© Copyright Pro Display 2009’
Step 3
Spray the glass with liquid glass polish and use a window scraper or blade to remove any dirt / blemishes from
the glass surface.
Repeat this procedure until you are happy the surface is smooth.
Step 4
Spray the glass with liquid glass polish and clean with a soft lint-free cloth. Repeat this process until you are
sure that the surface is completely clean.

5
‘© Copyright Pro Display 2009’
Step 5
Using a lint free cloth, wipe the glass surface with IPA (Isopropyl Alcohol) and leave to evaporate.
Step 6
Wipe down the protective liner on the cling side of the self adhesive Switchable Film to remove any dust.

6
‘© Copyright Pro Display 2009’
Step 7
Using the edge tab of the label remove the first 100mm (4”) of the protective liner covering the cling side on
the bus-bar edge. Make sure that you do this in a clean dust free environment.
Step 8
Align the bus-bar edge of the self adhesive Switchable Film with the top edge of the glass.When in position
run your finger along the bus-bar to fix the top edge (the adhesive strip will hold the film in position).

7
‘© Copyright Pro Display 2009’
Step 9
Gradually pull away the protective liner and allow the film to slowly adhere to the glass surface under its own
pressure. Using the roller move down the film working in horizontal lines left to right to disperse any air bub-
bles. If any small bubbles are visible, carefully lift the film and let it sit back down under its own pressure.
Step 10
Repeat the above process until you have a bubble-free installation.

8
‘© Copyright Pro Display 2009’
Step 11
Use the soft edge squeegee to work any small bubbles and the edges of the film. Please note that if any edges
are lifting slightly these will relax down once the protective liner is removed.
Step 12
Once the film is installed on the glass you can then start work on wiring the bus-bar. Carefully solder the
electrical cable to the mesh tags.There are two tags on the left hand side and two tags on the right hand side.
Solder a cable to one tag on the left (positive connection) and one tag on the right (negative connection).
The other tags are only there as spares.At this stage it would be good to connect the cables to a switch /
transformer and test the switching from frosted to clear. Once you have tested the switching you can them
trim off the spare mesh tags.

9
‘© Copyright Pro Display 2009’
Step 13
You can now lift the tag and carefully remove the protective liner.
Step 14
Run some clear double sided tape along the bus-bar edge to hold your electrical cables in place while you
prepare the cover trim.

10
‘© Copyright Pro Display 2009’
Step 15
Use Dow Corning (7091) non-acid based silicone along the bus-bar edge to hold the protective cover trim
in place.We recommend you use a plastic cover trim. if you wish to use a metal trim we would suggest that
you consult an electrician.
Step 16
Your installation is now complete and you can clean the film using either liquid glass polish or IPA cleaner
and a soft lint-free cloth. For most installations we would recommend that you use a cover trim on all edges
of the film.

11
‘© Copyright Pro Display 2009’
Step 17
The end result.