Intelligent Home Cronus User manual

Cronus Video Door System
2-wire Series
-1-
www.intelligenthomeonline.com
Installation and User Manual
Digital Touch Screen 7 inch Monitor
1
2
3
4

PRECAUTIONS
• Read this manual through before using the product
• Slots and openings in the back of the monitor, are provided for ventilation and to ensure
reliable operation of the video monitor or equipment and to protect it from overheating.
These openings must not be blocked or covered. The monitor should never be placed near
or over a radiator or heat register and should not be placed in a built-in installation such as a
bookcase unless proper ventilation is provided
• All parts should be protected from violent vibration. Prevent impacts, knocking and dropping
• Clean the LCD monitor with Plastic Protection cleaner only
• Imagedistortionmayoccurifthevideodoorphoneismountedtooclosetomagneticelde. g.
Microwaves, TV, computer etc.
• Please keep away the video door monitor from wet, high temperature, dust, and caustic and
oxidation gas in order to avoid any unpredictable damage
• Do NOT open the device in any condition, call the administrator for help if there is any
problem or malfunction happens

CONTENTS
Monitor Parts and Functions................................................................................................ 1-2
Mounting.................................................................................................................................. 3
Screen ..................................................................................................................................... 4
Answering a call ...................................................................................................................... 5
Adjusting screen&volume........................................................................................................ 5
Door Release. ....................................................................................................................... 7
Intercom Function.................................................................................................................. 7
Manual Monitoring. ................................................................................................................ 8
Operating Staircase Light...................................................................................................... 9
Call Divert.............................................................................................................................. 9
Monitor settings ..................................................................................................................... 10
Ring tone settings .................................................................................................................. 11
Language . ............................................................................................................................. 11
Restoring to default settings.................................................................................................. 12
Entering Installer setup. ........................................................................................................ 12
Screen calibration.................................................................................................................. 16
.......................................................................................................................... 16

-1-
Monitor Parts and Functions
1
7
9
2
3
4
5
6
8
10
NO. Item Description
1 Digital LCD touch screen • Display visitors' image
2 Power indicator ON when monitor powered
3 Message indicator ON when monitor has missed call
4 Unlock button Press to Unlock door or gate
5 Talk/Mon button • Press to communicate hands free with visitor
• Press to view outside in standby mode
6 MENU button Press to open Mainmenu
7 Microphone Transmitsthe audio from door station
8 Mounting hook Use to hang the monitor
9 Speaker Visitors voice coming from speakers
10 Connection port Bus connection terminal
1
2
3
4
SW+ SW- RING GND NC
1 2 3 4 5 6
ON
DIPS
L1
L2

-2-
Monitor Terminals
SW+ SW- RING GND NC
1 2 3 4 5 6
ON
DIPS
L1
L2
SW+
SW- RING
GND
NC
1 2 3 4 5 6
ON
DIPS
L1
L2
L1,L2: Bus line terminal
SW+,SW-: ExternalCallbutton
connection port
Ring,GND: External Ringer
connection port
NC: Not in use
DIP switches:
• DIP1~DIP5: User Code setting
• DIP6: End of line setting. Set ON
if the monitor is at the end of the
line or if connected with DBC4
Additional Call Button
Additional call button can be connected to a monitor via terminals SW+ White and SW- Green
wires
Please note: There will be no video on the monitor when somebody rings this call button
Additional External Ringer
Additional external ringer can be connected to a monitors via terminals RNG - Red wire to a
Positive and GND - Black wire to a Negative. One Ringer per monitor. Locate a ringer in a
position where you are unlikely to hear the ringing of the monitors; like a garage, shed, or
carport

1. Use the screws to fix the mounting bracket on the wall
2. Hang the Monitor on themounting bracket firmly
Monitor Mounting
Mounting screws
Monitor
Mounting bracket
2 wire cable
145~160 cm
-3-

LOGO
Touch to view info
about software version
and User Code
Screen
The Main menu is your starting point for using all the applications on your monitor
Touch screen anywhere and Main menu will appear as following:
CLOSE
Touch to switch off the screen
SETTINGS
Touch to enter
setup page
DIVERT
Touch to setup calldivert
function (if Telephone/GSM
Interfaces are connected)
Displays which door station
is calling
Displays talking time
LIGHT
Touch to operate the
staircase light (with
add. RLC Interface)
INNER CALL
Touch to start Intercom to all
rooms
MONITOR
Touch to view
outdoor
NAMELIST
Touch to start Intercom to
a specific room
CALL GUARD UNIT
Touch to call Guard Unit
Monitor
Main Menu- Home Page
Icons Visible During Talking
00:10 DS-1
-4-

Answering a Door Call
1
2
3
4
Here you can adjust your monitor properties such as Contrast, Brightness and Colour.
Following adjustments can be performed in ‘Manual Monitoring’ mode with video from Door
Station on a screen
Adjusting Colour,Brightness and Talk Volume
00:10 DS-1 00:10 DS-1
Normal
00:10 DS-1
BASIC OPERATIONS
• When Door Station is rung, the monitor comes On with video
• To start conversation touch TALK/MON
TALK/MON
icon on the button or Talk icon on the screen
•To end conversation touch icon on the button once again or touch icon
on the screen. Monitor will shut down automatically after 40 seconds
-5-

Here you can choose screen ratio 4:3 or 16:9
00:10 DS-1 00:10 DS-1
Normal
00:10 DS-1
5
5
5
5
Here you can adjust Speaker volume. The range are 0 (Mute) ~ 9
Touch - or + to set desired levels
4 scene modes are available to select: Normal, Bright, Soft and User
Screen Contrast. The range is 0~9. Touch -or +to set desired levels
Screen Brightness. The range is 0~9. Touch -or +to set desired levels
Screen Colour. The range is 0~9. Touch -or +to set desired levels
-6-

Electric Lock Release
Intercom Function
If system connected to a lock, you can open the lock from the Video Monitor. Video from Door
Station must be on the screen to perform unlocking
When multiple Monitors are installed, Intercom function between all Monitors in the system
becomes available. There are 3 Intercom functions to choose from:
1. Inner Call: all Monitors in the House system will ring at the same time. When one of the Monitors
answers the call, all other Monitors will stop ringing. In Apartments system can be used if multiple
Monitors has been installed in one of the apartments. All Monitors should be programmed with
same User Code. In addition one Monitor should be programmed as Master and other as Slaves
00:10 DS-1
1
Touch either or icon on the screen
or press UNLOCKbuttonon a side
to open the lock.
If two locks are connected to a door
station, touch
00:10 DS-1
* Use " " or " " to adjust the microphone volume
* Touch icon to end the call
-7-

-8-
00:10 DS-1 00:10 DS-1
[01]
[02]
[03]
[04]
[05]
3. Intercom with Guard Monitor: Applicable only for Apartments system if there is a concierge which has
a Monitor. Apartment can call the concierge or concierge can call any apartment in the system
How to set theMonitoras aGuard Monitor
2. Namelist: Allows
to call one specific Monitor at the time in House system or to call other apartments in
Apartment system. All Monitors should be programmed with unique User Codes/Addresses with DIP
switches. See ‘User Codes Tables’ on page 18
Code 8004# is used to set the Monitor as a Guard Monitor
Code 8005# is used to cancel this function
* Use <or > to scroll pages
* Touch to redial
* Calling ends automatically after 40 seconds if nobody answers the call
Touch anywhere of the screen or press the MENU button on the screen in standby mode
Touch MONITOR to enter Monitor Select page
Note: Press TALK/MON button in standby mode to monitor the Master Door Station in
shortcut
Monitoring Door Stations/CCTV C ameras
DS1~4 and CAM1~4 can be selected to monitor individually
Manual Monitoring Function
00:10 DS-1
Monitor Select
DS-1
DS-2
DS-3
CAM-1
DS-4
00:10 DS-1
* During Manual Monitoring there is no Audio by default
* Touch icon to enable the Audio

-9-
Call Divert Function
Forwarding a call from the system to a mobile phone requires an additional TPS Telephone
Interface or GSM Interface. Up to 3 mobile or land line numbers can be programmed
Setting Divert Number: On the Home page, touch ‘Divert’ icon
Touch the telephone number frame and type in the number/s using digital keypad
Touch # to save the setting
-
-
Operating Staircase Light
To use this function, the staircase light should be connected with additional Interface DT-RLC
Touch Light icon on home page or touch
icon during monitoring or talking to turn
the light On
*Touch Light icon again to turn off the light or it will be turned off automatically after 60 sec
or
*Touch icon again to turn off the light or it will be turned off automatically
00:10 DS-1

-10-
There are two Divert Modes available to choose from:
1. Divert, Simultaneously: call will be diverted immediately. All Monitors and home telephone
handsets will ring. All Monitors will come On with video from Door Station. Call can be answered
from any Monitor or home telephone handset
2. Divert, If No Answer: If Monitor is not answered within 30 s, call will be diverted to the
number programmed. Monitor/s will stop ringing after the diversion. Talking time is limited to 90
seconds
IMPOR TANT: If multiple Monitors installed, they should be programmed Master/Slave/s.
Program Divert mobile number/s on the Master Monitor and they will be shared with other Slave
Monitors automatically
NOTE: Remove ‘Voice mail’ in your mobile phone if you want dialling to a next number, if first
didn’t answer
Monitor Settings
Here you can set quantity of Door Stationsand CCTV c ameras, and monitoring time
1.On Home page, touch Settings icon
2.Touch +/ -,or / iconsto change the values
Note: Touch icon to exit and return to Home page. New settings are saved automatically
4
4
30 sec

-11-
Ring Tone Settings
Here you can set ring tones for multiple Door Stations and Intercom between Monitors to
distinguish different calling sources
On the Homepage, touch Settings icon ->
Touch Door Station, Intercom, Bell Button tone individually
Touch and icon to change. Setting will perform immediately
+/ -/
Note: Touch icon to exit and return to Home page
5
6
7
8
4
4
30 sec
• On the Home page, touch Settings icon -> Language..
• Choose desired language and touch to save the settings
Changing Language
4
4
30 sec
English
Turkish
Greek
Hebrew
Spanish
French

-12-
Torecover factory settings
• On the Homepage, touch Logo icon to enter About page
• Touch icon to restore to default
Restoring to Factory Default Settings
00.00
AUTO
00.01.00
• On the Home page, touch Logo icon to enter About page
• Press and hold for 2 sec UNLOCK button
• Digital keypad will be shown. Type in desired code/s following by #
For example:
8000 # -Master; 8001 # - Slave 1;
8006 # Power saving mode Off;
8405 # - Unlocking time is 5 sec
Entering Installer Setup
00.00
AUTO
00.01.00
_-

-13-
Setting Codes Tables
Toggle one of the DIP switchesand it will triggerAddress Setting page to come on screen.
There are two way to set the Address/User Code: via DIP switches on the rear of monitors or
via Address Setting page
Entering Address Setting Page
INSTALLER SETUP
_
SW+ SW- RING GND NC
1 2 3 4 5 6
ON
DIPS
L1
L2
01.00
Master
Code Setting Item Code Setting Item
2412 Reset To Default Setting 8016-8017 Bypass Enable/Disable
2499 Restore Factory Settings 8401-8499 Unlock Time
8000 Master Monitor 8018-8020 Video Display Standard
8001~8003 Slave Monitor 9015-9016 Enable/Disable Intercom Call
8006-8007 Setting Slave Monitor Panel On/Off 9017-9018 Screen Ratio 4:3/16:9
8010-8011 Unlock Mode:Close/Open
Select DIP Switcher Set Address setting, then touchicon, total 32 User C odes will
be displayed
Power Saving Mode On/Off
By default the system is set to Power Saving Mode, where only the first Monitor in the system
comes On with video when Door Station called. All other Monitors will ring but without video.
Video will be transferred to the Monitor which answers the doorbell call.
To switch the power saving mode Off: (so all Monitors ring with video) tick ‘Slave Panel On’ on
the ‘Address Setting’ page or type in code 8006 # on ‘Installer Setup’ page

-14-
All Monitors must have same User Code ‘0’ and programmed as Master/Slaves
Program first Monitor as Master, all others as Slave 1, Slave 2, Slave 3
If there are more than 3 Slave Monitors in the system, program them with different User Codes
starting with Code 0, 1, 2, 3, 4 and so on as for Star connection
In addition to User Code programming, last Monitor in the chain have to have DIP6 set On (end
of line). Applicable Intercom unction for Master/Slave programming- ‘Inner Call’- all Monitors
ring at the same time. Intercom by ‘Namelist’ requires different programming, same as for Star
connection
How to Program the ‘User Code’ for Star Connection
All Monitors must be connected to an additional hub-DBC4A distributor. One DBC4A can connect
up to 4 video Monitors. Each Monitor in the system should be assigned with the unique ‘User
Code’ according the tables on page 18 and have DIP6 set On in each Monitor in the system
How to Program the ‘User Code’ for Daisy Chain Connection
ON(1)
=
OFF(0)
=
ON
ON
ON DIP
123456
DIPstate Setting DIP state Setting
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
Monitor not at the
end of bus line
Monitor at the end
of bus line
End of line setting with DIP-6
There are two way of connecting multiple Monitors:
1. Daisy Chain - each Monitor connects to a next Monitor
2. Star Connection - all Monitors connects to a central point
Up to 16 video Monitors can be connected in a House system. Up to 4 Monitors in each apartment
for Apartments system. Each Monitor in either system must be programmed with a ‘User Code’- the
address
Multiple Monitor System Configuration
There are two ways to program User Codes: via DIP-switches on the rear of the M onitor or
via ‘Address Setting’ page
INSTALLER SETUP
_
SW+ SW- RING GND NC
1 2 3 4 5 6
ON
DIPS
L1
L2
01.00
Master

-15-
On ‘Address Setting’page, select Manual Input Address setting mode, then touch
Type in User C ode using digital keypad
Touch # key to save
Touch key to delete
Cursor Edit box
Delete the last character
Save setting
Exit current page
_
00-31
Always start with User Code 00 for House system and 01 for Apartment system.
Range of codes available 00-31. In addition program all Monitors as ‘Master’. Applicable
Intercom Function for such programming: ‘Intercom by Namelist’- to call to a specific Monitor in
the system
USER CODES TABLES
Note: In Apartment system program Apartment 32 with User Code ‘0’
Select DIP Switcher Set Address setting, then touchicon, total 32 User Codes will
be displayed on the screen. Same as in picture below

-16-
Specification
Screen Calibration
●Power supply for indoor monitor: DC 24V
●Power consumption: Standby15mA; Working 400mA
●Monitor screen: 7 Inch digital color LCD
●Display Resolution: 800*3(R, G, B) x 480 pixels
●Video signal: 1Vp-p, 75Ω, CCIR standard
●Wiring: 2 wires, no-polarity
●Dimensions: H125×W225×D23mm
• In standby mode, press UNLOCK button and hold for 3 seconds
• Red cross symbol will appear
• Keep touching Red cross symboluntil calibration complete and OK! will appear
1
2
3
4
1
2
3
4
+
+
+
1
2
3
4
OK!
+