M2I TOPR Series User manual

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
1 / 18
Thank you for purchasing the industrial HMI touch panel series of M2I corporation.
Please read this manual carefully to know installing, wiring, operating this equipment for safe use of this
product.
M2I Corporation
Industrial HMI Touch Panel
TOPR Series (Display Module)
Hardware Manual

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
2 / 18
Contents
Chapter 1. Safety Precautions.........................................................................................................................................................................3
■ Before using the product.............................................................................................................................................. 3
■ General Precautions ......................................................................................................................................................... 3
■ Design Precautions........................................................................................................................................................... 3
■ Wiring Precautions ........................................................................................................................................................... 4
■ Installation Precaution .................................................................................................................................................... 4
■ Disposal Precaution.......................................................................................................................................................... 4
Chapter 2. Overview............................................................................................................................................................................................5
2.1 Introduction of Products.............................................................................................................................................. 5
2.2 Package Contents............................................................................................................................................................ 5
2.3 Explanation of Model name ....................................................................................................................................... 6
Chapter 3. General Specifications .................................................................................................................................................................7
3.1 Electrical Specifications................................................................................................................................................. 7
3.2 Display Specifications .................................................................................................................................................... 7
3.3 Touch Specifications....................................................................................................................................................... 7
3.4 Sub Function Specifications (*Premium models only) ................................................................................... 7
3.5 Environment Specifications......................................................................................................................................... 7
3.6 Structure Specifications ................................................................................................................................................ 8
Chapter 4. Part Names and General Specifications..............................................................................................................................8
4.1 TOPRD□□10 / □□20................................................................................................................................................. 8
4.2 TOPRD□□30 / □□31................................................................................................................................................. 9
4.3 TOPRD□□40 ..................................................................................................................................................................11
Chapter 5. Installation ..................................................................................................................................................................................... 13
5.1 Installation Requirements ..........................................................................................................................................13
5.2 TOPR Assemble ..............................................................................................................................................................13
5.3 Installation Procedure..................................................................................................................................................14
5.4 Panel Cut-out ..................................................................................................................................................................15
5.5 Fixation ...............................................................................................................................................................................16
5.6 Front USB ..........................................................................................................................................................................17
Chapter 6. Maintenance ................................................................................................................................................................................. 17
6.1 Cleaning the Display ....................................................................................................................................................17
6.2 Periodic Check Points..................................................................................................................................................17
6.3 Problems with the Device..........................................................................................................................................17
Chapter 7. Products and Warning Label Location............................................................................................................................. 18
Chapter 8. Products Label ............................................................................................................................................................................. 18

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
3 / 18
Chapter 1. Safety Precautions
■Before using the product
To use the product safely and effectively, please read the contents of this manual thoroughly before use.
Please keep to the safety precaution, for it is to prevent accidents and potential danger from occurring. Safety
precaution is classified into ‘Warning’ and ‘Caution’ and their meanings are as follows. Also the indicated
illustrations on the product and in the manual have the following meanings.
Violating the instruction may result in serious personal injury or death.
Violating the instruction may result in slight personal injury or product damage.
Be cautious, for danger may be present.
Be cautious, for there is a possibility of an electric shock.
■General Precautions
Do not press the screen with a hard or sharp object (awl, screwdriver, pen) with too strong a force.
It may cause malfunction of touch due to damage of the front sheet.
Do not use or store in an environment with high vibration.
Do not allow foreign objects such as water, liquids, or metal powders to enter the product. This may
cause breakage or electric shock.
Do not allow foreign objects such as water, liquids, or metal powders to enter into the front(screen)
protective sheet. The screen may be invisible or may cause a malfunction of the touch.
Use the radio or mobile phone at least 30cm away from the main unit.
Two or fewer bright spots may appear on the LCD screen, and certain areas may appear brighter, but this
is not a defect in LCD characteristics.
Do not store or operate in direct sunlight. Direct sunlight can change the properties of the LCD.
■Design Precautions
Install protection circuit on the outside of Products to protect the entire control system when external
power supply or Products have problems.
As the malfunction & incorrect result of Products could damage the stability of the entire systems
and human body, you must install damage preventing interlock circuit such as emergency stop,
Protective circuits, positioning upper and lower limit switch and interlock for forward/reverse
operation.
When computer or other controllers communicate and exchange data with products or change operation
mode of products, set up protective sequence program in PC or Controller for protecting system from
communication error.
The output signal or communication lines should be separated from the power line or high tension wire.
They should be installed 100mm (3.94 Inch) or more from each other.

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
4 / 18
■Wiring Precautions
Be sure the wiring is done correctly by checking the product’s rated voltage and the terminal
layout. Incorrect wiring could result in fire, damage or malfunctions.
Tighten the terminal screw with the specified torque. If the screws of terminal are loose,
it could result in short circuit, fire, malfunctions.
FG Terminal must be used a dedicated ground. Not doing so could result in malfunctions.
a. Grounding should be the Class 3 grounding. The cable for grounding should be more than 4㎟
b. Grounding point be closed to the products and make short the distance to the ground cable if possible.
Please see below.
■Installation Precaution
Do not install the location which exceeds allowed temperature. Product can be damaged or shorten the
life. Especially Install environment as below should be avoided.
Do not Install product to the place which the ambient temperature is out of limits, from 0℃to 50℃or on the surface
of control board which high pressure equipment is installed..
Do not install to the place where strong shock or vibration continuously have impacted on product.
The space between back of product and back of control board must be more than 100mm for maintenance
and ventilation.
In order to improve water retention and ventilation, the space between the back of the main body and
the console box should be 100mm or more, and install the cooling fan when installed in an enclosed
space.
■Disposal Precaution
When you dispose of product and battery, please treat it as industrial waste. It can create poisonous
substances or explosion.

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
5 / 18
Chapter 2. Overview
2.1 Introduction of Products
This industrial HMI touch panel is an industrial control device required in industrial field. It is a device based
on RS-232C and RS-422/485, Ethernet which is used for the basic purpose of communication with another
device (PLC).
The TOPR series consists of a Process module(TOPRP□□□) and a Display module(TOPRD□□□□□).
This user manual is for a Display Module (TOPRD□□□□□).
2.2 Package Contents
The components of the product are as follows.
Before using the product, please check that all of the following components are included.
Item
Figure
Quantity
Display Module
1
Manual
1
Gasket
1
Mounting Clamp
TOPRD08
6
TOPRD10
8
TOPRD12
10
TOPRD15
10
Accessories
(Sold separate)
USB Memory
USB Cable
SD Card
Front Protect Sheet
User Options

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
6 / 18
2.3 Explanation of Model name
TOPR
T
□□
□□
□
□
-
Ex
Serise
Type
Screen Size
Option
Resolution
Power
-
Explosion proof
P : Process
08 : 8.4"
10 : Standard
Q : QVGA(320*240)
D : DC
Ex : Explosion proof or special model
D : Display
10 : 10.4"
20 : Premium
V : VGA(640*480)
A : AC
Blank: Non-explosion proof or
general model
T : P + D
12 : 12.1"
30 : Premium
S : SVGA(800*600)
15 : 15.0"
31 : Premium
X : XGA(1024*768)
* "S" for 12.1 "model: XGA
2.3.1 Process Module (Main Unit)
TOPR
P
□□
□
Serise
Type
Option
Power
10 : Standard
D : DC
20 : Premium
A : AC
2.3.2 Display Module (Accessory Unit)
Serise
Type
Screen Size
Option
Resolution
08 : 8.4”
10 : Standard
Q : QVGA(320*240)
10 :10.4"
20 : Premium
V : VGA(640*480)
12 : 12.1”
30 : "20" Premium + Extended auxiliary options
S : SVGA(800*600)
15 : 15.0”
31 : "30" Premium + capacitive touch sensor
X : XGA(1024*768)
40 : "30" Premium + Extended auxiliary options 2
W: WQVGA(480*272)
WVGA(800*480)

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
7 / 18
Chapter 3. General Specifications
3.1 Electrical Specifications
Input Voltage
By Process Module
12V, 3.3V
Consumption
Process Module only
6W or less
Process Module +
Display Module included
TOPRD08 Series
12W or less
TOPRD10 Series
15W or less
TOPRD12 10 / 20 / 30 / 31
15W or less
TOPRD12 40
30W or less
TOPRD15 Series
18W or less
3.2 Display Specifications
3.3 Touch Specifications
specification
Model
Touch Type
Built-in, Analog resistive touch sensor
TOPRD□□ 10 / 20 / 30 / 40
Built-in, capacitive touch sensor
TOPRD□□ 31
3.4 Sub Function Specifications (*Premium models only)
Functional
specification
Model
Front Carmera
Built-in, Resolution: VGA(640*480)
TOPRD□□ 20 / 30 / 31 / 40
Proximity sensor
Built-in, Sensing Distance 1.5M
TOPRD□□ 20 / 30 / 31 / 40
Brightness Sensor
Built-in, brightness controls
automatically as 10 level
TOPRD□□ 20 / 30 / 31 / 40
Infrared
communication.
(IrDA)
Built-in, 0.7M working distance,
communication with dedicated
equipment
TOPRD□□ 30 / 31 / 40
NFC
Built-in, Near field communication
13.56MHz, Receive only
TOPRD□□ 30 / 31 / 40
Iris Sensor
Built-in, working distance up to 0.8M
TOPRD□□ 40
3.5 Environment Specifications
Operation Temperature (℃)
-10 ~ +50
Storage Temperature (℃)
-20 ~ +60
Operation Humidity (%RH)
0 ~ 90 (No dew)
Atmosphere
No corrosive gas
Protection Classification
Conform to IP65 (Process Module: IP2X)
Color
16M Colors
Brightness Level
10 Level(by software)
Backlight Type
LED
Backlight Life
50,000 hours
Display Font
MS Windows Vector font possible Image font
Front LED Indicate
Built in

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
8 / 18
3.6 Structure Specifications
Cooling System
Natural air circulation
Case Material
AL(Aluminium)
Chapter 4. Part Names and General Specifications
4.1 TOPRD□□10 / □□20
4.1.1 External Dimension
Products
A(mm)
B(mm)
C (mm)
D (mm)
TOPRD08 Series
237
183
32.7
5
TOPRD10 Series
276
219.5
32.6
TOPRD12 Series
320
261
34.2
TOPRD15 Series
370
301
36.7

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
9 / 18
4.1.2 Front Part Names and Specifications
No.
Title
Description
Support Model
①
Power LED
System Power Status LED
All
②
Proximity
Sensor
Automatically Backlight ON/OFF by Sensing Person
coming
TOPRD□□20
③
Brightness
Sensor
Automatically Brightness Controls by Ambient
Brightness
TOPRD□□20
④
USB OTG
UP/Down load Project file
All
⑤
Camera
Resolution VGA(640*480)
TOPRD□□20
⑥
LCD Panel
TFT 16M Color LCD
All
⑦
Touch Panel
Analog resistive touch sensor
All
⑧
USB OTG Cover
Front USB OTG Cover hole
All
4.2 TOPRD□□30 / □□31
.

TOPR Series (Display Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
10 / 18
4.2.1 External Dimension
Products
A(mm)
B(mm)
C (mm)
D (mm)
TOPRD08 Series
237
183
32.7
5
TOPRD10 Series
276
219.5
32.6
TOPRD12 Series
320
261
34.2
TOPRD15 Series
370
301
36.7
4.2.2 Front Part Names and Specifications