Intellinet 524780, 524797, 524872, 524896 User manual

Wireless
300N ADsl2+
MoDeM
router
quick
iNstAll
guiDe
MODELS:
524780
524797
INT-524780/524797-QIG-1209-01

2
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™
Wireless 300N ADSL2+ Modem Router, Model 524780 (Annex A) or
Model 524797 (Annex B).
This quick install guide presents the basic steps required to set up and
operate this device. For detailed instructions, specications and regulatory/
compliance statements, refer to the user manual on the enclosed CD or
at www.intellinet-network.com. Easy-to-follow instructions in this guide
and the user manual help make installation quick and simple, so you’ll
soon be enjoying the benets of its many features:
• 2T2R MIMO technology for enhanced throughput and coverage
• Supports ADSL standards G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3
(ADSL2), G.992.4 (splitterless ADSL2), G.992.5 (ADSL2+) for Annex A
• Supports 24 Mbps ADSL2+ downstream data rate
• Supports Wi-Fi Protected Setup (WPS)
• Supports WEP and WPA/WPA2 (TKIP and AES) data encryption
• Integrated 10/100 Mbps LAN switch with Auto MDI/MDI-X support
• DHCP server assigns IP addresses for all LAN users
• DHCP server supports static lease management
• Supports port forwarding, DMZ (demilitarized zone), DDNS (dynamic
DNS), UPnP (Universal Plug and Play), SNMP management
• Integrated SPI rewall
• QoS (Quality of Service) bandwidth management
• VPN Pass Through (PPTP, IPSec, L2TP)
• Complies with 2.4 GHz Draft IEEE 802.11n standard and is backward
compatible with IEEE 802.11g/b standards
• Easy installation through Web-based user interface
• System status, security log, rmware upgradeable
• Lifetime Warranty (except where limited — see package)
Package Contents
• Wireless 300N ADSL 2+ Modem Router
• Quick installation guide
• Setup CD with user manual and setup wizard
• Power adapter
• Ethernet Cat5 RJ45 cable, 1.0 m (3 ft.)
• RJ11 telephone cable, 1.8 m (5.9 ft.)

3
hArDWAre setup/coNNectioNs
1. Connect the router to your ADSL cable using the supplied RJ11 cable.
2. Connect the router to your PC, hub or switch by attaching the Ethernet
cable to the LAN port of the router.
3. Connect the power adapter to the power jack on the rear panel of
the router.
4. The ADSL LED will be on if the router is connected to the ADSL cable
and receives the ADSL signals successfully. If the LED is blinking,
contact your ISP (Internet service provider) to check the problem.
NOTE: Use only the power adapter included with the router, and not any
other power adapter.
setup WizArD
This router provides a Setup Wizard for conguring the ADSL settings.
This wizard collects some ISPs’ ADSL settings so that you can easily
congure the router’s ADSL settings just by selecting the ISP vendor
from the wizard. If you can’t nd your ISP from the list in the wizard,
manually set the ISP information. Both procedures are presented below.
Getting Started
Before starting, check the following items:
• Make sure you’ve connected the ADSL cable to the router correctly.
When the ADSL cable is worked normally, the ADSL LED will be on.
• Un-install any dial-up programs installed previously for the USB modem
or other dial-up devices.
• It’s recommended that you initially congure the router through the
Ethernet cable before you set the wireless functions.
This wizard can be run in Windows 98SE/Me/2000/XP/Vista. The
following procedures are operated in Windows XP. (Procedures are
similar for Windows 98SE/Me/2000/Vista.)
1. Insert the enclosed setup CD into your CD-ROM drive. The
Autorun.exe program should be executed automatically. If not, run
Autorun.exe manually from the “Autorun” folder on the CD.

2. The following screen will be displayed. Click “Setup Wizard.”
3. The wizard will run and try to search for the router. If the router is
found, the wizard will guide you to Step 5.
4

5
4. If the router can’t be found, enter the IP address and the password
of the router to search again. Click “Next” to continue.
5. The wizard will automatically select the country you’re in by checking
the language of the operating system in your computer and then
advance to the Select ISP screen. Select the ISP. If you can’t nd
the ISP, click “Other” to reselect the country or manually congure
the ISP information.

6
Setting the ISP Automatically
If you can nd the ISP from the wizard, follow the steps below to let the
wizard set the ISP settings automatically.
1. Select the ISP of your ADSL service.
2. Enter the username and password your ISP has provided, if needed.
Click “Next.”

7
3. Click “Save” to save the settings and reboot the router.
4. After saving and rebooting the router, the ISP settings are done. The
wizard will then help to set your computer to obtain an IP address from
the router automatically. A screen with a status bar will display to
indicate the progress of the procedure.
NOTE 1: To use the router to access the Internet, the IP address of each
PC needs to be set in the same network segment as the router. The
wizard will help to set the proper IP address for your computer.
NOTE 2: By default, the router’s DHCP server is enabled. If it’s disabled
before running the wizard, the wizard will enable the DHCP server
automatically.
5. The wizard will attempt to connect to the ISP you’ve selected. If the
connection fails, a screen prompt will display to indicate this is the
case. Run the wizard to select the ISP again.

8
6. If you do successfully connect to the ISP, you’ll see the screen below.
To congure additional settings, click “Advanced Settings” to go the
Web management of the router, or click “Finish” to close the wizard.
Setting the ISP Manually
If you can’t nd the ISP from the wizard, follow the steps below to set the
ISP settings manually.
First, check with your ISP (Internet service provider) as to what kind of
service is provided, such as PPPoE, PPPoA or RFC1483/2684. Gather
the information as illustrated in the table below and keep it for reference.
PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password (and Service Name).
PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password.
RFC1483 Bridged VPI/VCI, VC-based/LLC-based multiplexing to use
Bridged Mode.
RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing, IP Address,
Subnet Mask, Gateway Address, and Domain Name
System (DNS) IP Address (a xed IP address).

9
1. Select “Other.”
2. Check with your ISP as to the connection type of the ADSL line. Select
the Connection Type and click “Next.”
NOTE: The wizard will automatically select the country you’re in by
checking the language of the operating system in your computer and
then skip to the Select ISP screen. If you want to change the country,
click “Back” here.

10
3. Input the VPI, VCI and encapsulation data supplied by your ISP. If the
Connection Type is “Static IP Address,” you need to input the IP
address information supplied by your ISP. For details about each
setting, refer to Section 5.2 in the user manual.
4. Enter the username and password that your ISP has provided, if
needed. Click “Next.”