Intellinet 561143 User manual

24-Port Gigabit Ethernet PoE+ Switch
with 10 GbE Uplink
User Manual
Model 561143
intellinet-network.com

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch
Contents
Chapter 1 Product Introduction .................................................................... 3
1.1 Product Overview............................................................................................3
1.2 Features..........................................................................................................3
1.3 Package Contents ..........................................................................................4
Chapter 2 External Component Description................................................5
2.1 Front Panel .....................................................................................................5
2.2 Rear Panel......................................................................................................7
Chapter 3 Installing and Connecting to the Switch .................................... 8
3.1 Installation.......................................................................................................8
3.1.1 Desktop Installation ..............................................................................8
3.1.2 Rack-mountable Installation in a 19-inch Cabinet ................................9
3.1.3 Power On the Switch ............................................................................9
3.2 Connect Computer to the Switch ..................................................................10
3.3 Switch connection to the PD.........................................................................10
Appendix:......................................................................................................11
Technical Specifications .....................................................................................11
Warranty .............................................................................................................12
Notes ..................................................................................................................13
Copyright ............................................................................................................13
Federal Communication Commission Interference Statement ...........................15

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
3
Chapter 1 Product Introduction
Thank you for purchasing the Intellinet 24-Port Gigabit Ethernet PoE Switch with 10
GbE Uplink. Before you install and use this product, please read this manual carefully
to fully understand the functions of this product.
1.1 Product Overview
This 24-port 10/100/1000Mbps + 2 1000/10000Mbps SFP+ Slots PoE Ethernet
Switch provides seamless network connection. The high performance of this switch
upgrades your old network to a 1000Mbps Gigabit network. Based on Gigabit
Ethernet Technology, the switch alleviates network bottlenecks that frequently
develop as more advanced computer users and newer applications place greater
demands on network resources. SFP+ supports trunking for high-bandwidth data
links.
The switch's RJ45 PoE ports can automatically detect and supply power to
IEEE802.3at-compliant Powered Devices (PD). Electrical power is transmitted along
with data in a single cable, allowing you to expand your network where there are no
power lines or outlets or where you wish to install devices like IP Cameras or IP
Phones, etc.
The switch is easy to install and use. It requires no configuration and installation. It's a
great selection for expanding your office network.
1.2 Features
This switch complies with IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x,
IEEE802.3az, IEEE802.3ae standards. Other features of the switch are as follows:
•Power and data connection for up to 24 PoE network devices
•Delivers data and power over existing network cables, which saves on
electrical installation costs
•Includes two small form-factor pluggable 10 GbE SFP/SFP+ module slots
•10/100/1000 auto-sensing ports automatically detect optimal network speeds
•Supports IEEE 802.3at and IEEE 802.3af-compliant PoE devices (wireless
access points, VoIP phones, IP cameras)
•Trunking for SFP1 and SFP2 can be activated via switch on front panel
•88 Gbps switch fabric
•PoE power budget of 400 watts
•Complies with the IEEE 802.3az (Energy Efficient Ethernet EEE) specification
•Two high-volume cooling fans ensure perfect ventilation
•Includes 19" rackmount brackets

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
4
1.3 Package Contents
• 24-Port Gigabit Ethernet PoE+ Switch with 2 x 10 GbE SFP+ Uplinks
• Power cable
• User manual
• 19" rackmount brackets

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
5
Chapter 2 External Component Description
2.1 Front Panel
The front panel of the switch consists of a series of LED indicators, 24 x
10/100/1000Mbps RJ-45 ports, 2 x 1000/10000Mbps SFP+ ports, one Flow Control
switch and one Trunking switch, as shown below:
Figure 1 - Front Panel
10/100/1000Mbps RJ-45 ports (1-24):
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or
1000Mbps. Each has a corresponding Link/Act LED.
SFP+ ports (25, 26):
Designed to install the SFP+ module and connect to the device with a bandwidth of
1000Mbps or 10000Mbps. Each has a corresponding Link/Act LED.
Flow Control switch:
Turns Flow Control ON or OFF.
Port Trunking switch:
Turns SFP+ port Trunking ON or OFF.
LED indicators:
The LED indicators allow you to monitor, diagnose and troubleshoot any potential
problem with the switch, connection or its attached devices.
Figure 2 - LED Indicators
The following chart shows the LED indicators of the switch along with explanation of
each indicator.

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
6
LED
COLOR
STATUS
STATUS DESCRIPTION
PWR
Green
On
Power On
Off
Power Off
1-24
（Link/Act）
Orange
(10/100Mbps)
On
A device is connected to the port.
Off
A device is disconnected from the
port.
Green
(1000Mbps)
Flashing
Sending or receiving data
1-24
（POE）
Green
On
There is a PoE PD connected to
the port, which is successfully
being supplied power.
Off
No Powered Device is connected to
the port, or no power is supplied
according to the power limits of the
port.
25-26
（Link/Act）
Orange
(1000Mbps)
On
A device is connected to the port.
Off
A device is disconnected from the
port.
Green
（10G）
Flashing
Sending or receiving data

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
7
2.2 Rear Panel
The rear panel of the switch contains an AC power connector, as shown below.
Figure 3 - Rear Panel
AC Power Connector:
Power is supplied through an external AC power adapter. It
supports AC 100~240V,
50/60Hz.
Grounding Terminal:
Located on the left side of the power supply connector; use a grounded connection to
prevent electric shock.

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
8
Chapter 3 Installing and Connecting to the Switch
This chapter describes how to install your Ethernet switch and make connections to it.
Read the following sections and perform the procedures in the order presented to
avoid incorrect installation, which will cause damage to the device and will threaten its
security.
3.1 Installation
Place the switch in a stable location or on a desktop.
Make sure the switch works in the proper AC-input range and matches the voltage
labeled on the switch. Do not ever open the switchʼs shell,even in a power failure.
Ensure that there is adequate space around the switch for proper ventilation and heat
dissipation. When installing the switch in a cabinet, make sure the cabinet will
adequately support the weight of the switch and its accessories.
3.1.1 Desktop Installation
If installing the switch on a desktop, attach the provided cushioning rubber feet on the
bottom of each corner of the switch to prevent external vibration. Allow adequate
space for ventilation and heat dissipation between the device and the objects around
it.
Figure 4 - Desktop installation

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
9
3.1.2 Rack-mountable Installation in a 19-inch Cabinet
The switch can be mounted with an EIA standard-sized, 19-inch rack, which can be
placed in a wiring closet with other equipment. To install the switch, follow these
steps:
Attach the mounting brackets on the switchʼs side panels (one on each side) and
secure them with the screws provided.
Figure 5 - Attaching Brackets
Use the screws provided with the equipment rack to mount the switch on the rack and
tighten it.
Figure 6 - Mounting switch
3.1.3 Power On the Switch
The switch is powered on by the AC 100~240V 50/60Hz internal high-performance
power supply. Follow the next tips to turn on the switch:
AC Electrical Outlet:
Intellinet recommends using a single-phase three-wire receptacle with a neutral outlet
or a multifunctional computer-professional receptacle. Make sure to connect the metal
ground connector to the grounding source on the outlet.

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
10
AC Power Cord Connection:
Connect the AC power connector on the back panel of the switch to an external
receptacle with the included power cord, and check that the power indicator turns on.
When it is ON, the device is receiving power.
3.2 Connect Computer to the Switch
Connect one end of an Ethernet cable to an RJ45 jack on your computer; connect the
other end to any RJ45 port of the switch. The maximum distance between the switch
and the computer should not exceed 100 meters. Once your devices are connected
and powered on, the Link/Act status indicator lights activate with the corresponding
ports on the switch.
Figure 7 - Connect Computer (NIC) to the switch
3.3 Switch connection to the PD
All 24 ports on the switch have PoE power-supply capability. The maximum output
power of one port is up to 30W. The switch powers PD devices such as Internet
phones, network cameras, wireless access points, etc. through Ethernet cables.

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
11
Appendix:
Technical Specifications
Standards
IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x,
IEEE802.3az, IEEE802.3ae
Number of Ports
24 x 10/100/1000Mbps Auto-Negotiation ports
2 x 1000/10000Mbps SFP+ ports
Network Media (Cable)
10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ù STP (maximum 100m)
100Base-Tx: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ù STP (maximum 100m)
1000Base-T: UTP category 5e, 6 cable (maximum 100m)
Capability
Store-and-Forward
Supports
Switching Capacity
88Gbps
MAC Address
Learning
Automatically learning, automatically Update 16K Table
LED indicators
Per-Port
Link/Act
10/100Mbps:orange
1000Mbps:green
PoE: green
SFP+
Link/Act
10000Mbps: green
1000Mbps: orange
Other
Power: green
Environment
Operating Temperature: 0℃~40℃(32°F~104°F)
Storage Temperature: -40℃~70℃(-40°F~158°F)
Operating Humidity: 10%~90% non-condensing
Storage humidity: 5%~90% non-condensing
PoE Power on RJ45
Power+: pin 1 & pin 2
Power-: pin3 & pin 6
Power
AC 100V~240V 50/60HZ 6.5A (Internal Power supply)

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
12
Warranty
Deutsch Garantieinformationen finden Sie hier unter
intellinetnetwork.com/warranty.
English For warranty information, go to intellinetnetwork.com/warranty.
Español Si desea obtener información sobre la garantía, visite
intellinetnetwork.com/warranty.
Français Pour consulter les informations sur la garantie, rendezvous à lʼadresse
intellinetnetwork.com/warranty.
Italiano Per informazioni sulla garanzia, accedere a intellinetnetwork.com/warranty.
Polski Informacje dotyczące gwarancji znajdująsięna stronie
intellinetnetwork.com/warranty.
México Póliza de Garantía Intellinet — Datos del importador y responsable ante el
consumidor IC Intracom México, S.A.P.I. de C.V. • Av. Interceptor Poniente # 73, Col.
Parque Industrial La Joya, Cuautitlan Izcalli, Estado de México, C.P. 54730, México. •
Tel. [phone]
La presente garantía cubre los siguientes productos contra cualquier defecto de
fabricación en sus materiales y mano de obra.
A. Garantizamos cámaras IP y productos con partes móviles por 3 años.
B. Garantizamos los demás productos por 5 años (productos sin partes móviles), bajo
las siguientes condiciones:
1. Todos los productos a que se refiere esta garantía, ampara su cambio físico, sin
ningún cargo para el consumidor.
2. El comercializador no tiene talleres de servicio, debido a que los productos que se
garantizan no cuentan con reparaciones, ni refacciones, ya que su garantía es de
cambio físico.
3. La garantía cubre exclusivamente aquellas partes, equipos o sub-ensambles que
hayan sido instaladas de fábrica y no incluye en ningún caso el equipo adicional o
cualesquiera que hayan sido adicionados al mismo por el usuario o distribuidor.
Para hacer efectiva esta garantía bastará con presentar el producto al distribuidor en
el domicilio donde ue adquirido o en el domicilio de IC Intracom México, S.A.P.I. de
C.V., junto con los accesorios contenidos n su empaque, acompañado de su póliza
debidamente llenada y sellada por la casa vendedora indispensable el sello y fecha
de compra) donde lo adquirió, o bien, la factura o ticket de compra original donde se
mencione claramente el modelo, numero de serie (cuando aplique) y fecha de
adquisición. Esta garantía no es válida en los siguientes casos: Si el producto se
hubiese tilizado en condiciones distintas a las normales; si el producto no ha sido
operado conforme a los instructivos de uso; o si el producto ha sido alterado o tratado
de ser reparado por el consumidor o terceras personas.

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
13
Notes
Copyright

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
14
Copyright ©2015 IC Intracom. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission of this company.
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is." Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves
the right to revise this publication and to make changes from time to time in the
contents thereof without obligation to notify any person of such revision or changes.

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
15
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance could
void the authority to operate equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Safety
This equipment is designed with the utmost care for the safety of those who install and
use it. However, special attention must be paid to the dangers of electric shock and
static electricity when working with electrical equipment. All guidelines of this and of
the computer manufacture must therefore be allowed at all times to ensure the safe
use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany,
Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United
Kingdom. The ETSI version of this device is also authorized for use in EFTA member
states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not Intended for Use
None

24-Port 10/100/1000Mbps + 2-Port 1000/10000Mbps SFP+ Ethernet Switch |
16
intellinet-network.com
© IC Intracom. All rights reserved.
Intellinet is a trademark of IC Intracom, registered in the U.S. and other countries.