Intellinet 524063 User manual

GiGabit
EthErnEt
rackmount
WEb-Smart
SWitch
uSEr
manual
MODELS 524063
& 524087
INT-524063/524087-UM-0308-01
Model shown: 524063, 24-port

introduction
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™
Gigabit Ethernet Rackmount Web-Smart Switch, Model 524063 (24-port)
or Model 524087 (16-port).
This handy device lets you increase the speed of your network with
10/100/1000 Mbps auto-sensing ports that automatically detect optimal
network speeds, and it lets you increase the speed of your own work
through user-friendly Web-based management for uncomplicated
administration.
Easy-to-follow instructions in this user manual help make installation of
the switch quick and simple, so you’ll also soon be enjoying the benets
of these additional features:
• All RJ-45 ports with Auto-MDIX (auto uplink) support
• Supports NWay auto-negotiation
• Broadcast storm control with multicast packet rate settings
• Store and forward switching architecture
• Full/half duplex operation
• IEEE 802.3x ow control for full duplex
• Zero packet loss backpressure ow control for half duplex
• Packet ltering/forwarding rates: 1,488,000 pps (1000 Mbps), 148,800 pps
(100 Mbps), 14,880 pps (10 Mbps)
• Supports port controls (speed, ow control and maximum frame size)
• Supports VLAN (tag-based and port-based)
• Supports link aggregation (trunking)
• Supports QoS (Quality of Service) with 2 priority levels
• Provides IEEE 802.1x port-based security
• Supports port mirroring
• Supports jumbo frames up to 9.6 kBytes
• 19” rackmount
• LEDs for power, link/activity, connection speed
• Lifetime Warranty
NOTE: Some screen images have been modied to t the manual format.
3

SEtup
• Using twisted-pair cable, connect the switch to your computer.
• Using the included power cord, connect the Gigabit Ethernet
Rackmount Web-Smart Switch to an AC power source.
confiGuration
1. Set your PC’s
IP address to
192.168.2.xxx
(where “xxx”
is a value from
2 to 254).
2. Open the Web
browser; go to
192.168.2.1 to
display the
conguration
login screen.
4
LED Status Operation
POWER On There is power to the unit.
1000M On The corresponding port is transmitting/receiving at 1000 Mbps.
Off The corresponding port is transmitting/receiving at 10/100 Mbps.
LINK/ACT On The corresponding port is connected to another device.

3. Enter “admin” in the
Password eld, then
click “Apply.” The
authentication process
will now allow you to
navigate among/within
the primary menu options: Conguration, Monitoring and Maintenance.
Conguration
System
This screen presents the
MAC address, system
rmware version and
several other settings/
readings. You can change
the user name, password
and IP address, then click
“Apply” to conrm any
changes. After that, you
can reset the switch to
make the new username,
password or IP address
take effect.
5

Ports
This screen gives
you the option of
enabling/disabling
Jumbo Frames.
Plus, by selecting
each individual port
you can:
• enable/disable
the port
• choose between
full and half
duplex
• select a Mode option from the dropdown menu, such as “Auto Speed”
• enable/disable Flow Control
VLAN
Depending on the model
of the Gigabit Ethernet
Rackmount Web-Smart
Switch, there are either
24 VLAN groups (1 – 24
for Model 524063) or 16
VLAN groups (1 – 16 for
Model 524087). Select
and enter a group into
the “VLAN ID” eld, click
“Add,” then click the port number(s) you want to put into the selected
VLAN group.
Aggregation/Trunking
Set up any port trunk groups you prefer, then click the port numbers you
want to include in the same group. There are eight groups that can be
created, and the maximum number of ports for any one group is 24 for
Model 524063; 16 for Model 524087.
6

LACP
Select the port number(s) for
which you want to enable/disable
the protocol.
RSTP
Select the port
number(s) for which
you want to enable/
disable the protocol.
7

802.1x
This screen gives you drop-down menu options — “Auto,” “Force
Authorized” and “Force Unauthorized” — for the Admin State of the
selected port(s).
IGMP
Snooping
This screen
allows you to
enable/disable
IGMP for the
selected
port(s).
Port Mirroring
Port Mirroring is used to mirror trafc
from a source port to a destination port
for analysis. Select the destination port
(1 – 24 for Model 524063; 1 – 16 for
Model 524087) in the left-hand column,
then select the source port by checking
the corresponding “Mirror Source” box
in the right-hand column.
8

QoS (Quality of Service)
When QoS Mode is enabled, you can
select the Quality of Service for each
individual port.
Filter
Select the port
number(s) for
which you want to
enable/disable IP
address ltering.
Rate Limit
Select the port number(s)
for which you want to
establish/change speed
settings.
Storm Control
This screen lets you congure the
various settings of Storm Control
in order to minimize interference
with trafc to and from the switch.
9

Monitoring
Statistics Overview
This screen lets you monitor the current status and statistics for each of
the ports.
Detailed Statistics
This screen lets you view detailed statistics by clicking on the port in the
top panel.
10