Interlogix FW5.1 User manual

P/N 1073029-EN • REV B • ISS 16JUN15
TruVision IP PTZ
Camera FW5.1
Installation Guide

Copyright © 2015 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies
Corporation. All rights reserved.
Trademarks and
patents
The Product Name and logo are trademarks of United Technologies.
Other trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Manufacturer Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
ACMA compliance Notice! This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Canada This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du Canada.
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC Fire & Security declares that this device is in
compliance with the essential requirements and other relevant provisions of Directive
2004/108/EC.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of
as unsorted municipal waste in the European Union. See the product documentation for
specific battery information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.
Contact information
For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu.

Installation Guide 3
Content
Introduction 3
Product overview 4
Before you begin 4
Installation environment 5
Camera description 5
Connections 7
Installing a camera 9
Pendant-mount camera 9
TVP-1122/3122 pendant-mount camera 11
Flush-mount camera 11
Surface-mount camera 14
Using the camera with an Interlogix NVR or Hybrid DVR or
another system 18
Using the camera with TruVision Navigator 18
Accessing the camera over the internet 18
Specifications 20
Pin definitions 21
Introduction
This installation guide provides basic information on setting
up and using the camera. Detailed information on the
cameras can be found in the configuration manual.

4 Installation Guide
Product overview
This is the installation guide for following TruVision IP PTZ
camera models:
TVP-1101 (1.3 MPX pendant, 20X, PAL)
TVP-3101 (1.3 MPX pendant, 20X, NTSC)
TVP-1102 (1.3 MPX surface, 20X, PAL)
TVP-3102 (1.3 MPX surface, 20X, NTSC)
TVP-1103 (1.3 MPX flush, 20X, PAL)
TVP-3103 (1.3 MPX flush, 20X, NTSC)
TVP-1104 (2 MPX pendant, 20X, PAL)
TVP-3104 (2 MPX pendant, 20X, NTSC)
TVP-1105 (2 MPX surface, 20X, PAL)
TVP-3105 (2 MPX surface, 20X, NTSC)
TVP-1106 (2 MPX flush, 20X, PAL)
TVP-3106 (2 MPX flush, 20X, NTSC)
TVP-1107 (2 MPX pendant, 30X, PAL)
TVP-3107 (2 MPX pendant, 30X, NTSC)
TVP-1122 (2 MPX pendant, 30X, IR, PAL)
TVP-3122 (2 MPX pendant, 30X, IR, NTSC)
Before you begin
Unpack everything. Check the items for damage, and verify
that all items are included. The camera is shipped with the
following items:
Dome camera
Installation Guide
CD with the Configuration Manual and Device Manager

Installation Guide 5
Installation environment
When installing your camera, consider these factors:
•Place the camera in a secure location.
•Ensure that the camera is in a well-ventilated area.
•Do not expose the camera to rain or moisture.
Caution: Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries according to the
instructions.
Camera description
Figure 1: Overview of the dome camera (pendant-mount
shown)

6 Installation Guide
TVP-1122/3122 cameras only:
1. Power supply cord
Connect 24 VAC power supply
2. Video output
Connect the BNC connector to a
CCTV monitor
3. Ethernet RJ45 connector.
Connect to the network devices
Connect to the PoE+ switch
4. Alarm input/outputs and audio
in/out port
5. Housing
6. Bubble
7. Metal housing
8. IR LEDs
9. Camera

Installation Guide 7
Connections
There are seven built-in alarm inputs to use as internal
alarm triggers and two alarm built-in outputs in the camera
housing. These connections do not apply to the TVP-
1122/3122 cameras.
Note: The DIP switches are not used.
Figure 2: Connections to the circuit board (excludes
TVP-1122/3122)
1. Power supply: Connect +24 VAC power supply and GND.
2. RJ45 connector: Connect to the network.
Caution: The RJ45 connector on the camera module is not for connecting
the network. It is an RS-232 port for troubleshooting.
3. Alarm inputs 3 to 7: Connect to up to five alarm input devices.
4. GND
5. Alarm inputs 1 and 2: Connect to up to two alarm input devices.
6. Alarm outputs 1 and 2: Connect up to two output devices
7. AIN, AOUT: Connect audio input, audio output, and GND to the audio
terminals.
8. VIDEO: Connect a CCTV monitor to the video terminals.
Alarm input and output connections
The alarm output can be used to turn on and off an external
alarm device. Connect a 30 VDC/1 A external power supply

8 Installation Guide
to the alarm output. If using an AC power supply, an
external relay must be used to prevent electric shock and
damage to the device. See Figure 3 below.
Figure 3: External alarm output
Direct current:
Dome camera
relay output
Alternating current:
Dome camera
relay output

Installation Guide 9
Installing a camera
Pendant-mount camera
1. Prepare the mounting surface and install the camera
bracket.
2. Unscrew the bubble from the camera and remove the
protective tape from the PTZ module (excluding TVP-
1122).
3. Press the two tabs on either side of the PTZ module
and remove the module from the camera housing
(excluding TVP-1122).
4. Route the cables from the pendant bracket as shown
below.
RED AC24V
YELLOW/GREEN
BLACK AC24V

10 Installation Guide
5. Attach the safety cable to the bracket and connect the
cables to the PCB of the module through the cable entry
hole on top of the housing.
Safety cable
Note: If alarm and audio input/output relays are to be
used, also connect them to the PCB of the module.
Caution:The safety cable is made of metal. Please
ensure that it does not touch the PCB of the module.
6. Attach the camera housing to the bracket using the
screws enclosed with the bracket.
7. Insert the PTZ module into the housing:
Position the tabs on the PTZ module by aligning the
arrow label on the module with those on the housing
(see below). The module should firmly snap into
position. If using a SD card, insert it into the module
before inserting the module into the housing.