Interlogix TruVision 6 Series User manual

TruVision
Series 6 IP
Camera Installation
Guide
P/N 1073465-EN • REV B • ISS 13DEC18

Copyright © 2018 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls & Security, a
unit of United Technologies Corporation. All rights
reserved.
Disclaimer Information in this document is subject to change
without notice. No part of this document may be
reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose, without the
express written permission of UTC Fire & Security
Americas Corporation, Inc.
Trademarks and
patents
Trade names used in this document may be trademarks
or registered trademarks of the manufacturers or
vendors of the respective products.
Manufacturer Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923,
USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
FCC compliance Class A: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.

Installation Guide iii
FCC conditions This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This Device must accept any interference received,
including interference that may cause undesired
operation.
ACMA compliance Notice! This is a Class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take
adequate measures.
Canada This Class A digital apparatus complies with CAN
ICES-003 (A)/NMB-3 (A).
Cet appareil numérique de la classe A est conforme à
la norme CAN ICES-003 (A)/NMB-3 (A).
European Union
directives
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon
the purchase of equivalent new equipment, or dispose
of it at designated collection points. For more
information see: www.recyclethis.info.
2013/56/EU & 2006/66/EC (battery directive): This
product contains a battery that cannot be disposed of
as unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return
the battery to your supplier or to a designated collection
point. For more information see: www.recyclethis.info.

Product warnings and
disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE TO
AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY CANNOT
PROVIDE ANY ASSURANCE THAT ANY PERSON
OR ENTITY BUYING ITS PRODUCTS, INCLUDING
ANY “AUTHORIZED DEALER” OR “AUTHORIZED
RESELLER”, IS PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY INSTALL FIRE AND
SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-warning/
or scan the QR code:
Contact information
and manuals/ tools/
firmware
For contact information and to download the latest
manuals, tools, and firmware, go to the web site of your
region.
Americas: www.interlogix.com
EMEA: www.firesecurityproducts.com
Manuals are available in several languages.
Australia/New Zealand: www.utcfs.com.au

Installation Guide 1
Safety instructions
These instructions are intended to ensure that user can use
the product correctly to avoid danger or property loss.
The precaution measures are divided into “Warnings” and
“Cautions”.
Warnings: Warning messages advise you of
hazards that could result in injury or loss of life.
They tell you which actions to take or to avoid in
order to prevent the injury or loss of life.
Cautions: Caution messages advise you of
possible equipment damage. They tell you which
actions to take or to avoid in order to prevent
damage.
Warnings
•When using this product, you must comply with the
electrical safety regulations of the country and region.
Please refer to the technical specifications for detailed
information.
•Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 24 VAC
or 12 VDC according to the IEC60950-1 standard. Please
refer to the technical specifications for detailed
information.
•Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire
hazard.

2 Installation Guide
•Please make sure that the plug is firmly connected to the
power socket. When the device is mounted on a wall or
ceiling, it should be firmly fixed to the surface.
•If smoke, odor or noise rises from the device, turn off the
power at once and unplug the power cable. Then please
contact the service center.
•Proper configuration of all passwords and other security
settings is the responsibility of the installer and/or end-
user.
Cautions
•Make sure the power supply voltage is correct before
using the camera.
•Do not drop the camera or subject it to physical shock.
•Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe
it gently. If the camera will not be used for an extended
period, please replace the lens cap to protect the sensor
from dirt.
•Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not
a malfunction), and affect the endurance of sensor at the
same time.
•The sensor may be burned out by a laser beam, so when
any laser equipment is in using, make sure that the
surface of sensor will not be exposed to the laser beam.
•Do not place the camera in extremely hot, cold (the
operating temperature is-30°C ~+60°C, or -40°C ~ +60°C
if the camera model has an “H” in its suffix), dusty or
damp locations, and do not expose it to high
electromagnetic radiation.

Installation Guide 3
•To avoid heat accumulation, good ventilation is required
for operating environment.
•Keep the camera away from liquid while in use.
•During delivery, the camera shall be packed in its original
packing, or packing of the same texture.
•Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average
time varies because of differences between operating
environment and using history, so regular checking is
recommended for all the users. Please contact with your
dealer for more details.
•Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent
type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.
•If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume
any responsibility for problems caused by unauthorized
repair or maintenance.)

4 Installation Guide
Content
Introduction 6
Product overview 6
Contact information and manuals /tools /firmware 8
Installation 9
Installation environment 10
Package contents 11
Cable requirements 24
Camera description 25
Setting up the camera 33
IR illuminators 33
Accessing the Micro SD card 34
Mounting the bullet camera 34
Mounting the turret camera 40
Mounting the dome camera 47
Mounting the wedge camera 57
Using the protective water resistant connector cover 61
Network access 65
Checking your web browser security level 65
Activating the camera 67
Using the camera with a TruVision recorder or another
system 70
Using the camera with TruVision Navigator 70
Specifications 71
TruVision IP fixed lens bullet cameras 71
TruVision IP motorized lens bullet cameras 71

Installation Guide 5
TruVision IP fixed lens turret dome 72
TruVision IP motorized lens turret dome 73
TruVision IP fixed lens dome cameras 73
TruVision IP motorized lens dome cameras 74
TruVision IP fixed lens wedge cameras 75
Pin definitions 76

6 Installation Guide
Introduction
Product overview
This is the installation guide for TruVision Series 6 IP camera
models:
TVB-5601 (2MPX IP fixed lens bullet camera)
TVB-5602 (4MPX IP fixed lens bullet camera)
TVB-5603 (8MPX IP fixed lens bullet camera)
TVB-5604 (2MPX IP motorized lens bullet camera)
TVB-5605 (4MPX IP motorized lens bullet camera)
TVB-5606 (8MPX IP motorized lens bullet camera)
TVT-5601 (2MPX IP fixed lens turret camera, gray)
TVT-5602 (2MPX IP fixed lens turret camera, white)
TVT-5603 (2MPX IP fixed lens turret camera, black)
TVT-5604 (4MPX IP fixed lens turret camera, gray)
TVT-5605 (4MPX IP fixed lens turret camera, white)
TVT-5606 (4MPX IP fixed lens turret camera, black)
TVT-5607 (8MPX IP fixed lens turret camera, gray)
TVT-5608 (2MPX IP motorized lens turret camera, gray)
TVT-5609 (4MPX IP motorized lens turret camera, gray)