Interlogix UVD-IP-XP4DNR-VA2 User manual

UltraView IP XP4 Dome
Day/Night Range Camera
Quick Start Guide
P/N 1072567B-EN • REV 1.0 • ISS 23JUL12

EN 2 UltraView IP XP4 Dome Day/Night Range Camera
Introduction
The UVD-IP-XP4DNR(-P) color video camera uses a digital signal
processor (DSP) to process video signals. The video camera includes
a microcontroller to provide high-quality images in changing lighting
environments with high-color reproduction and sharp pictures.
Product codes:
• UVD-IP-XP4DNR-VA2(-P)
• UVD-IP-XP4DNR-VA9(-P)
Package contents
The UVD-IP-XP4DNR(-P) camera is shipped with the following items:
• The camera assembly
• 1 channel passive video transceiver
• AC power wiring harness
• Mounting screws, wall anchors, and hex key
• 150 mm DC jack to terminal adapter
Installation environment
To install the camera you will need to prepare the mounting surface,
make cable connections, and mount the camera.
Cable requirements
Cable type Requirements
Video 75 ohm RS-59 coaxial cable with BNC ends
Power 24 VAC cable
Network RJ45 Ethernet cable

UltraView IP XP4 Dome Day/Night Range Camera 3 EN
Camera description
Figure 1: Camera assembly
Camera body
RJ45 Ethernet/PoE input
24 VAC / 12 VDC input
Video output (BNC)
Plenum-compliant cabling
The cable connections must be enclosed in a suitable metallic, or other
fire-resistant, low-smoke producing enclosure. The cabling used within
the air space must be specifically marked for that purpose or enclosed
in a conduit.
Re-route the leads from the camera so they exit from the threaded
knockout on the side of the camera (see Figure 2 on page 4). Move
the plug from the side threaded knockout and place it on the knockout
on the base of the camera.

EN 4 UltraView IP XP4 Dome Day/Night Range Camera
Figure 2: Plenum-compliant cabling
1. Plenum-rated conduit
2. Box for connections
3. Threaded knockouts
4. Ceiling
5. Camera body
6. Trim ring
Installation
Viewing the camera via an IP connection
You can connect the IP camera to a network and view the images
through a browser. To view via a Network Video Recorder or similar
digital video system, please refer to the documentation associated with
that system.
Software requirements
The UVD-IP-XP4DNR(-P) camera requires:
Microsoft Internet Explorer
A VLC player ActiveX plug-in is required to play video when
Internet Explorer is used to monitor the camera.

UltraView IP XP4 Dome Day/Night Range Camera 5 EN
Figure 3: ActiveX plug-in option
To configure the camera:
1. Configure the UVD-IP camera with a default IP address: 10.1.2.11
2. Configure your host PC/laptop within the same subnet, ex:
10.1.2.10
3. Connect the URL http://10.1.2.11 with Internet Explorer.
4. Select the “Live” menu to view live video.
5. Enter the following username and password to access the
Maintenance menu.
Login: admin
Password: admin
The IP address of the camera can be changed from the
Maintenance menu.
6. Reboot the camera for the changes to take effect.

EN 6 UltraView IP XP4 Dome Day/Night Range Camera
Connecting analog cables
To connect the cables:
1. Connect a coaxial cable from the camera’s BNC connector to a
CCTV monitor or video recording device.
2. Connect Ethernet cable from the camera RJ45 port to switch
3. Connect a PoE switch, a 12 VDC or 24 VAC power supply to the
power input. Do not connect both the PoE connection and DC or
AC connection at the same time. The label on the camera gives
the following information:
Red cable. Power in.
Black cable. Power in.
White cable. Video out.
Black cable. Video ground.
Note: For 24 VAC or 12 VDC, Black or Red may be used for ground.
Installing the camera
To mount the camera, attach the camera to the mounting surface using
the appropriate fasteners.
Angle adjustment
See Figure 4 on page 7 and do the following:
To adjust the horizontal angle of the platform up to 180 degrees, turn
the platform.
To adjust the horizontal angle of the rotor up to 350 degrees, turn the
rotor on the platform.
To adjust the vertical angle of the platform up to 90 degrees, turn the
platform.

UltraView IP XP4 Dome Day/Night Range Camera 7 EN
Figure 4: Camera adjustment
Platform horizontal adjustment
Platform vertical adjustment
Rotor horizontal adjustment
Zoom and focus adjustment
See Figure 5 below for the location of the zoom and focus ring
thumbscrews.
Figure 5: Zoom and focus adjustment
Zoom ring thumbscrew for
VA2 and focus ring for
VA9 lens
Focus ring thumbscrew for
VA2 and zooming ring for
VA9 lens
To adjust the camera zoom and focus:
1. Loosen the zoom ring thumbscrew.
2. Turn the zoom ring to set the desired zoom.
3. Tighten the zoom ring thumbscrew.
4. Loosen the focus ring thumbscrew.
5. Turn the focus ring to set the desired focus.
6. Tighten the focus ring thumbscrew.

EN 8 UltraView IP XP4 Dome Day/Night Range Camera
Figure 6: DIP switch layout (back of camera)
Table 1: DIP switch functions (Default in bold)
Switch Description
1. White Balance
ON: ATW mode; OFF: PTL mode
2. Backlight Compensation
ON: BLC on; OFF: BLC off
3. Exposure AI/AE
ON: Auto Exposure (AE) mode; OFF: Auto Iris (AI) mode
4. Day/Night Setting
ON: Black and white mode; OFF: Auto Day/Night mode
5. High/Normal Resolution
ON: High resolution; OFF: Normal resolution
6. Flickerless Control
ON: Flickerless enabled; OFF: Normal
Reset to factory default settings
Use the reset button to reset the camera to factory defaults including
camera and network settings. With the camera powered up, press the
red reset button for 10 to 15 seconds. The red LED indicator light
flashes when the reset signal is accepted.
Contact information
For contact information see our Web site: www.interlogix.com