Interlogix TruVision TVB-2401 User manual

© 2015 United Technologies Corporation. All rights reserved. P/N 1072936-EN • REV A • ISS 26MAR15
Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved.
TruVision High Definition TVI Bullet Camera
Installation Guide
Product overview
This is the Installation Guide for TruVision High Definition TVI
Bullet Camera TVB-2401/TVB-4401 and TVB-2403/TVB-4403.
This guide describes a standard installation.
Package contents:

Camera with power and
video output cables

3 screws and 3 anchors
for wall or ceiling
installation

Template

Installation Guide
•WEEE and Battery
Disposal

CD
Camera description
TVB-2401/TVB-4401
1. TVI video output cable (grey)
2. Power cable
3. Mounting base output
4. Sun shield
5. Lens
6. IR LED
TVB-2403/TVB-4403
1. WDR/CVBS switch cable
2. Power cable
3. TVI video output cable (grey)
4. CVBS video output cable
(black)
5. Mounting base
6. Sun shield
7. Lens
8. IR LED
Note:
Please check the camera output settings before setting up a
system. The TVI video output can be only connected to a DVR
with TVI signal input. The CVBS output supports the standard
monitor, test monitor, encoder and DVR.
For TVB-2403/TVB-4403, you can connect the white and black
line ends of the WDR switch cable to enable the Wide Dynamic
Range (WDR) function. The WDR function is disabled by
default. If WDR is enabled, the CVBS output will be blocked
out, and only TVI output is available.
Installation
To install the camera on a ceiling:
1. Using the template, place it level against the mounting
surface and mark the position of the mounting holes.
2. Following all local codes, drill and prepare the mounting
holes.
3. Securely fasten the mount to the mounting surface with
the screws.
5
6
42
1
3
7
8
6
2
1
3
4
5
Drill Template

2 / 3 P/N 1072936-EN • REV A • ISS 26MAR15
4. Using a 75-ohm coaxial video cable, connect the camera
TVI video output and a TVI DVR, and connect a 12 VDC
power supply to the camera power cable.
5. Adjust the camera position and angle as required.
Programming
Programming on TVI output:
Programming on TVI output is available for TVB-2403/TVB-
4403 only.
Once the camera hardware has been installed, you can
configure the camera settings on the TVI DVR.
Select PTZ protocol as TruVision Coax and click menu button
to call up the camera menu.
For more details, please see the TVI DVR user manual.
Programming on CVBS output:
Programming on CVBS output is available for TVB-2403/TVB-
4403 only.
Programming on CVBS output, you need to connect a monitor
and a TVS-C200 controller (purchase separately) as following
system figure.
The TVS-C200 has one male BNC output and a female output.
Please connect the male output to camera’s CVBS output and
female output to a monitor.
Specifications
Power supply
12 VDC
Current
TVB-2401/TVB-4401: Max.300mA
TVB-2403/TVB-4403:
Max. 330mA
Power consumption
TVB-2401/TVB-4401:
Max. 3.5 W
TVB-2403/TVB-4403:
Max.4 W
Weight
TVB-2401/TVB-4401: 0.64 lb. (291 g)
TVB-2403/TVB-4403:0.68 lb. (309 g)
Dimensions
(Ø × L)
2.76 x 5.89 in. (70 x 149.5 mm)
Setup menu
Regulatory information
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
FCC compliance
Class A: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
ACMA compliance
Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
Canada
This Class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-0330 du Canada.
Certification
N4131
360°
90°
360°

P/N 1072936-EN • REV A • ISS 26MAR15 3 / 3
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC Fire
& Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive
2004/108/EC.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste i
n the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Copyright
© 2015 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial
Systems, a unit of United Technologies
Corporation. All rights reserved.
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.