Interlogix Ultra View UVD-6120VE-2 User manual

UltraView UVD-6120VE-2
Digital WDR Dome
Camera User Manual
P/N 1072553A • REV 1.0 • ISS 18JUN12

Copyright
©
2012 UTC Fire & Security. All rights reserved.
Trademarks and
patents
The
TruVision and Interlogix names and logo are trademarks of
UTC
Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance
Class A:
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated i
n a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
ACMA compliance
Notice!
This is a Class A product. In a domestic environment this
product may cause
radio interference in which case the user may be
required to take adequate measures.
European Union
directives
12004/108/EC (EMC directive):
Hereby, UTC Fire & Security
declares that this device is in compliance or with the essential
requirements and ot
her relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upo
n the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information
, see www.utcfireandsecurity.com or
www.utcfssecurityproducts.eu
.

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 1
Content
Product overview 2
Package Contents 2
Features 2
User guidelines 2
Product description 3
OSD control pad 3
Installation 5
Mount the camera 5
Connect the cables 5
Adjust the lens 5
Adjust the focus and zoom 6
Programming 7
Access the Main menu 7
General menu 7
AE/WDR/BLC menu 8
WB mode menu 9
D/N mode menu 9
Motion alarm menu 10
Privacy menu 11
Picture adjustment menu 12
Reset camera 12
Specifications 12
Dimensions 13
Menu Map 14

2 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual
Product overview
The UVD-6120VE-2-XX camera uses a digital signal processor (DSP) to process
video signals. The camera includes a microcontroller to provide high-quality
images with high-color reproduction and sharp pictures.
Package Contents
The package contains the following:
• Dome camera
• Monitor output cable
• Mounting screws, wall anchors, and hex wrench
• Power terminal
• Ceiling drilling holes template
Note: Use the video output BNC and power jack for normal system operation.
Use the monitor output cable for installation and maintenance.
Features
The camera includes the following features:
• EXview HAD II (hole accumulated diode) technology with 480,000 pixels
NTSC (570,000 PAL)
• Use of LSI (large scale integration) digital processors to produce 650 lines of
horizontal resolution
• Smart digital control automatic BLC (backlight compensation)
• Digital wide dynamic range (WDR)
• Advanced auto exposure system for both fixed iris and auto iris lenses to
optimize the amount of light
• Internal synchronization
• Eight privacy mask areas to protect privacy concerns
• Advanced OSD (onscreen display) control
• Signal-to-noise ratio better than 52 dB
• Long life and high reliability
• Isolated switching power 12 VDC and 24 VAC
User guidelines
• Program the camera settings as much as possible before mounting the
camera. Take appropriate safety precautions while completing programming
after installation.

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 3
• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the
camera.
• Do not use the camera over the temperature range specifications: - 22 to
122°F (-30 to +50°C).
• If the light source where the camera is installed experiences rapid, wide-
variations in lighting, the camera may not operate as intended.
WARNING: To reduce the risk of fire or electronic shock, do not expose the
camera to rain or moisture and do not remove the cover or back.
Product description
Figure 1:: Camera description
Camera body
OSD control
pad
System heater
Power jack
Monitor output cable:
1. Monitor output BNC; 2.
Monitor output RCA
Video monitor output Video output BNC
OSD control pad
The onscreen display (OSD) control pad (Figure 3) is a five-direction pad that
provides the ability to manually control the camera functions. Table 1 below lists
the OSD control pad functions and describes their use.

4 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual
Figure 2: OSD control pad
OSD control pad
Table 1: OSD control pad functions
Pad directions Description
Up Moves the cursor upward to select an item.
Left Moves the cursor left to select or adjust the options of the selected
item.
Right Moves the cursor to the right to select or adjust the options of the
selected item.
Down Moves the cursor downward to select an item.
Enter
Press the center of the control pad to display the Setup menu. If the
selected item has its own menu, press the control pad to enter a
submenu. Press the control pad for 2 seconds to save all settings
and exit the Setup menu.

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 5
Installation
Please check the package contents and make sure that the device in the
package is in good condition and all the assembly parts are included.
To install the camera you will need to prepare the mounting surface, mount the
camera, make cable connections, adjust the lens and then secure the dome
cover securely.
Note: Before installing, please ensure that the mounting surface is strong enough
to withstand three times the weight of the camera. If the mounting surface is not
strong enough, the camera may fall and cause serious damage.
Mount the camera
Use the ceiling drilling holes template and mark the holes on the ceiling with a
pen. Attach the plate with fasteners to the ceiling and then attach the camera
body to the plate.
To mount the camera, attach the camera to the mounting surface using the
appropriate fasteners.
Connect the cables
To connect the cables:
1. Connect a coaxial cable from the camera’s BNC connector to a CCTV
monitor or video recording device.
2. Connect the 12 VDC or 24 VAC power supply to the power jack of the
camera.
Caution: Check for polarity when using a 12 VDC power supply.
Adjust the lens
The camera is mounted on a pan-tilt-twist (3-axis grimbal) rotating platform so
that it is easy to adjust the camera orientation. See Figure 3 on page 6.

6 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual
Figure 3: Camera adjustment
Platform horizontal adjustment (0 to 180°)
Platform vertical adjustment (0 to 90°)
Rotor horizontal adjustment (0 to 350°)
To adjust the lens:
See Figure 3 above.
1. To adjust the horizontal angle of the platform up to 180 degrees, turn the
platform.
2. To adjust the horizontal angle of the rotor up to 350 degrees, turn the rotor on
the platform.
3. To adjust the vertical angle of the platform up to 90 degrees, turn the
platform.
Adjust the focus and zoom
Figure 4: Zoom and focus adjustment
Zoom ring thumbscrew
Focus ring thumbscrew
To adjust the camera zoom and focus:
1. Loosen the zoom ring thumbscrew and turn the zoom ring to set the desired
zoom. Tighten the thumbscrew.
2. Loosen the focus ring thumbscrew and turn the focus ring to set the desired
focus. Tighten the thumbscrew.

UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 7
Programming
Access the Main menu
The Main menu provides access to the camera configuration options. The on-
screen display (OSD) is only available in English.
Program the camera by attaching a standard video monitor to the system.
Figure 5: The Main menu
To access the menus:
1. Press the OSD control pad to access the Main menu and its submenus.
2. Push the pad up, down, left and right to move between menu options.
3. Press the OSD control pad (Enter) to select an option.
4. When in a sub menu, select Return to return to the previous menu.
5. To exit the Main menu, move the cursor to Exit at the bottom of the screen
and press Enter. All changes are saved.
General menu
Select the General option from the Main menu to enter the General menu.
Figure 6: The General menu
Table 2: General menu
Parameter Description
ID display Displays the camera ID on screen. Default option is Off.
Mirror Flips the camera image so that it is correctly orientated for viewing.

8 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual
Parameter Description
Default option is Off.
DNR Digital noise reduction (DNR) improves the image quality in low light
levels.
When enabled, select the Y and C filter strength: Press Return to return
to the previous menu or Exit & Save to save changes and return to live
mode. Default option is On.
Return Press Enter to return to the previous menu.
Exit & Save Exits the menu and returns to live mode. Saves changes made.
AE/WDR/BLC menu
Select the AE/WDR/BLC option from the Main menu to enter the AE menu.
Figure 7: The AE/WDR/BLC menu
Table 3: AE/WDR/BLC menu
Menu item Description
Lens type Defines the lens type used with the camera.
Select Fixed or DC. If DC is enabled, select the DC level and shutter speed
from the options shown.
WDR/BLC set Wide dynamic range (WDR) allows you to see details of objects in shadows or
details of objects in bright areas of frames that have high contrast between
light and dark areas such as the headlights of a passing car.
Backlight compensation (BLC) function improves image quality when the
background illumination is high. It prevents the object in the center from
appearing too dark.
Options are:
•Off
•WDR: Set the luminance level ( Low, Middle, High)
•BLC fix: set the BLC level (between 1 and 30) and the BLC window.
AGC max Defines the automatic gain control (AGM).
Select a value between 0 and 160.
Flicker This feature to prevent the strobing effect under certain lighting
conditions/shutter speeds.
Default option is Off.
Return Press Enter to return to the previous menu.
Exit & Save Exits the menu and returns to live mode. Saves changes made.