Interlogix TruVision Series User manual

TruVision Stainless Steel
PTZ Camera Installation
Guide
P/N 1073420-EN • REV A • ISS 30JAN18

Copyright
© 2018 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls & Security, a unit of
United Technologies Corporation. All rights reserved.
Trademarks
and patents
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
FCC
compliance
Class A: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC
conditions
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This Device must accept any interference received, including
interference that may cause undesired operation.
ACMA
compliance
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Canada
This Class A digital apparatus complies with CAN ICES-003
(A)/NMB-3 (A). Cet appareil numérique de la classe A est
conforme à la norme CAN ICES-003 (A)/NMB-3 (A).
European
Union
directives
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info.

Product
warnings
and
disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE TO, AND
INSTALLATION BY, AN EXPERIENCED SECURITY
PROFESSIONAL. UTC FIRE & SECURITY CANNOT PROVIDE
ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING
ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS
PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY
INSTALL SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and product safety
information, please check
www.firesecurityproducts.com/policy/product-warning/ or scan the
following code:
Contact
information
and manuals
For contact information go to: www.interlogix.com or
www.firesecurityproducts.com
To get translations for this and other product manuals go to:
www.firesecurityproducts.com

Content
Introduction 6
Product overview 6
Installation 6
Installation environment 6
Package contents 7
Camera description 10
Alarm input and output connections 11
SD memory card installation 11
Mounting the PTZ dome camera 12
Mounting the junction box 13
Using the camera with an Interlogix NVR or Hybrid DVR or
another system 15
Using the camera with TruVision Navigator 16
Access the camera over the internet 16
Specifications 19
PTZ camera 19
PTZ camera junction box 19
Pin definitions 20
Installation Guide 5

Introduction
Product overview
This is the installation guide for the TruVision Stainless Steel
PTZ dome camera model:
•TVP-5201 (2MPX wall-mount PTZ dome camera, 23X)
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
•Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 24 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.
•Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
•Temperature: Do not operate the camera beyond the
specified temperature, humidity, or power source ratings.
The operating temperature of the camera is between -40
to 60°C (-40 to140°F). Humidity is below 90%.
•Moisture: Do not expose the camera to rain or moisture
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified
6Installation Guide

service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.
•Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.
•Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
Package contents include the following:
Camera
Installation manual
Installation Guide 7

CD with configuration manual
and TruVision Device
Manager
Equipment disposal sheet
Battery disposal sheet
Hex wrench
Junction box
Screw A (10 pcs.)
13.6 mm
(0.54 in.)
1.6 mm
(0.06 in.)
5.85 mm
(0.23 in.)
5.5 mm
(0.22 in.)
5.0 mm
(0.20 in.)
10.7 mm (0.42 in.)
Screw B (4 pcs.)
25 mm
(0.98 in.)
5.4 mm
(0.21 in.)
13 mm
(0.51 in.)
16 mm (0.63 in.)
Blue sealing plug (3 pcs.)
6 mm (0.24 in.)
23.5 mm
(0.93 in.)
20.5 mm (0.81 in.)
A-A
A
A
6 mm (0.24 in.)
8 mm (0.31 in.)
8 Installation Guide

White sealing plug (3 pcs)
A-A
A
A
23.5 mm
(0.93 in.)
6 mm (0.24 in.)
20.5 mm (0.81 in.)
8 mm (0.31 in.)
10 mm (0.39 in.)
Black sealing plug (3 pcs)
A-A
A
A
23.5 mm
(0.93 in.)
20.5 mm (0.81 in.)
6 mm (0.24 in.)
11 mm (0.43 in.)
13 mm (0.51 in.)
Drill template – junction box
328 mm (12.91 in.)
113 mm (4.45 in.)
CAUTION: Use direct plug-in UL listed power supplies
marked Class 2/CE certified or LPS (limited power source) of
the required output rating as listed on the unit.
Installation Guide 9

Camera description
Figure 1: PTZ camera description and connectors
VIEOD
1200 mm (47.24 in.)
250 mm (9.84 in.)
①
②
③
④
⑤
⑥
⑦
1. 24V power supply (red 24 VAC,
yellow_green ground, black 24
VAC)
2. RS-485 (Orange RS-485+,
Yellow RS-485-)
3. Audio in (red_white) / Audio
output (blue_white)
4. Alarm inputs (green, blue,
purple, gray, white,
black_white, brown_white) /
two alarm outputs (red, pink)
5. 960H analog output
6. RJ45 network cable
7. Safety lanyard
10 Installation Guide