Interlogix TruVision TVB-2401 User manual

TruVision High Definition TVI
Bullet Camera Installation
Guide
TVB
-2401, TVB-4401
TVB-2403, TVB-4403
P/N 1072936-EN • REV A • ISS 12MAR15

Installation Guide 1
Contents
Product overview 1
Camera description 3
Installation 5
Programming 7
Setup menu 9
Specifications 10
Legal and regulatory information 11
Product overview
This is the Installation Guide for TruVision High
Definition TVI Bullet Camera TVB-2401/TVB-4401 and
TVB-2403/TVB-4403. This guide describes a standard
installation.

2 Installation Guide
Package contents:
Camera with power
and video output
cables
3 screws and 3
anchors for wall or
ceiling installation
Template
Installation Guide
•WEEE and Battery
Disposal
CD

Installation Guide 3
Camera description
TVB-2401/TVB-4401
1. TVI video output
cable (grey)
2. Power cable
3. Mounting base
output
4. Sun shield
5. Lens
6. IR LED
5
6
42
1
3

4 Installation Guide
TVB-2403/TVB-4403
1. WDR/CVBS switch
cable
2. Power cable
3. TVI video output
cable (grey)
4. CVBS video output
cable (black)
5. Mounting base
6. Sun shield
7. Lens
8. IR LED
Note:
Please check the camera output settings before setting
up a system. The TVI video output can be only
connected to a DVR with TVI signal input. The CVBS
output supports the standard monitor, test monitor,
encoder and DVR.
7
8
6
2
1
3
4
5

Installation Guide 5
For TVB-2403/TVB-4403, you can connect the white
and black line ends of the WDR switch cable to enable
the Wide Dynamic Range (WDR) function. The WDR
function is disabled by default. If WDR is enabled, the
CVBS output will be blocked out, and only TVI output
is available.
Installation
To install the camera on a ceiling:
1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.
2. Following all local codes, drill and prepare the
mounting holes.
3. Securely fasten the mount to the mounting
surface with the screws.
Drill Template

6 Installation Guide
4. Using a 75-ohm coaxial video cable, connect the
camera TVI video output and a TVI DVR, and
connect a 12 VDC power supply to the camera
power cable.
5. Adjust the camera position and angle as required.
360°
90°
360°

Installation Guide 7
Programming
Programming on TVI output:
Programming on TVI output is available for TVB-
2403/TVB-4403 only.
Once the camera hardware has been installed, you
can configure the camera settings on the TVI DVR.
Select PTZ protocol as TruVision Coax and click
menu button to call up the camera menu.
For more details, please see the TVI DVR user manual.
TVI

8 Installation Guide
Programming on CVBS output:
Programming on CVBS output is available for TVB-
2403/TVB-4403 only.
Programming on CVBS output, you need to connect a
monitor and a TVS-C200 controller (purchase
separately) as following system figure.
The TVS-C200 has one male BNC output and a
female output. Please connect the male output to
camera’s CVBS output and female output to a monitor.
TVI
CVBS

Installation Guide 9
Setup menu

10 Installation Guide
Specifications
Power supply
12 VDC
Current
TVB-2401/TVB-4401:
Max.300mA
TVB-2403/TVB-4403:
Max. 330mA
Power
consumption
TVB-2401/TVB-4401:
Max. 3.5 W
TVB-2403/TVB-4403:
Max.4 W
Weight
TVB-2401/TVB-4401: 0.64 lb.
(291 g)
TVB-2403/TVB-4403:0.68 lb.
(309 g)
Di
mensions
(Ø × L)
2.76 x 5.89 in. (70 x 149.5 mm)

Installation Guide 11
Legal and regulatory
information
Copyright:
© 2015 United Technologies Corporation,
Interlogix is part of UTC Building & Industrial Systems, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and patents:
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer:
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification:
N4131
FCC compliance: Class A
Class A: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
op
erated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause

12 Installation Guide
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
ACMA compliance
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.
European Union directives:
12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares
that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:
www.recyclethis.info.
Contact information:
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu