Interlogix TVW-6101 User manual

TruVision
HD-TVI (1080P) /
Analog Wedge Camera
Installation Guide
TVW
-6101
P/N 1073422-EN • REV A • ISS 14MAY18

Installation Guide 1
Content
Product overview 2
Contact information and
manuals/tools/firmware 2
Package contents 3
Camera description 6
Installation 7
Program 14
Using a TVI output 15
Call up the camera OSD (On Screen
Display) menu 15
Menu tree 18
Video format (NTSC/PAL) 19
Specifications 19
Legal and Regulatory information 20

2 Installation Guide
Product overview
This is the Installation Guide for the HD-TVI
(1080P) / analog wedge camera TVW-6101. This
guide describes a standard installation.
The configuration manual is available from our web
site.
Contact information and
manuals/tools/firmware
For contact information and to download the latest
manuals, tools, and firmware, go to the web site of
your region.
Americas: www.interlogix.com
EMEA:
www.firesecurityproducts.com
Manuals are available in
several languages.
Australia/New
Zealand:
www.utcfs.com.au

Installation Guide 3
Package contents
Camera
assembly (cable
harness not
shown)
3 M4 x 25 mm
screws and 3
anchors for wall
or ceiling
installation
Camera drill
template
2 screws M4 x 8
used for installing
the camera to the
adapter plate

4 Installation Guide
Torx wrench Adapter plate
Adapter plate drill
template
12 VDC
connector (2
terminal
connectors with
positive and
negative
indicators)
Lens adjustment
tool
Installation guide

Installation Guide 5
•Equipment
disposal sheet

6 Installation Guide
Camera description
1. 12 VDC power cable
2. TVI / 960H analog
video output
3. OSD menu button
4. Camera housing
5. TVI / 960H analog
switch
6. Power LED
7. MIC (Audio not
supported)

Installation Guide 7
Note: When using the HD-TVI output, the HD-TVI
wedge camera should only be connected to a DVR
that supports a TVI signal.
Installation
To install the camera on a surface:
1. Use the camera drill template to mark the
mounting holes.
2. Follow all local safety regulations. Drill through
the mounting surface. If you need to route the
cables from the bottom of the camera, drill a
larger hole in the mounting surface for the
cable harness.
3. Using the Torx wrench, loosen the four screws
to remove the housing cover from the device.

8 Installation Guide
4. Install the mounting base to the surface using
two of the M4 x 25 mm screws and anchors. If
routing the cable harness through the ceiling,
do so prior to mounting the camera.
5. Loosen the Philips screw, located near the lens
assembly. Align the lens adjustment tool with
the two small holes located on the camera
assembly.
Rotate (pan) the camera assembly using the
lens adjustment tool until the lens is positioned

Installation Guide 9
in the correct location. The tool is also used to
adjust the tilt angle.
Philips screw
Pan
Lens adjustment tool
Tilt
Rotation

10 Installation Guide
Note: Please do not remove the foam ring
attached to the lens. This foam ring is required
to reduce the glare of IR illuminators.
6. Tighten the Torx screw and re-install the
housing cover to the camera assembly using
the Torx wrench.
To install the camera using the adapter plate:
1. Use the adapter plate drill template to mark the
holes.

Installation Guide 11
2. Follow all local safety regulations. Drill through
the mounting surface. If you need to route the
cables from the bottom of the camera, drill a
larger hole for the cable harness.
3. Install the adapter plate to the using two of the
M4 x 25 mm screws and anchors.

12 Installation Guide
4. Using the Torx wrench, loosen the four screws
to remove the housing cover from the device.
5. Install the camera base to the adapter plate
using the two M4 x 8mm screws.
6. Loosen the Philips screw located near the lens
assembly. Align the lens adjustment tool with
the two small holes located on the camera
assembly.

Installation Guide 13
Rotate (pan) the camera assembly using the
lens adjustment tool until the lens is positioned
in the correct location. The tool is also used to
adjust the tilt angle.
Philips screw
Pan
Lens adjustment tool
Tilt
Rotation

14 Installation Guide
Note: Please do not remove the foam ring
attached to the lens. This foam ring is required
to reduce the glare of IR illuminators.
7. Tighten the Philips screw and re-install the
housing cover to the camera assembly using
the Torx wrench.
Program
In HD-TVI or Analog mode, use the OSD (On
Screen Display) button to program the camera. The
button is located on the cable harness. In HD-TVI
mode, the OSD menu can also be accessed via the
TVI recorder.

Installation Guide 15
Using a TVI output
Once the camera has been installed, you can
configure the camera settings on the TVI DVR.
Connect the TVI cable to the DVR, as shown.
Select the PTZ protocol TruVision Coax and click
the Menu button to call up the camera menu.
For more details, refer to the TVI DVR user manual.
Call up the camera OSD (On Screen
Display) menu
To set up the camera in HD-TVI mode:
1. In Camera Settings of the DVR, access the
PTZ menu and select the TruVision-Coax
protocol for the TruVision HD-TVI camera from
the drop down menu.

16 Installation Guide
2. In live view of the desired camera, click the
PTZ Control icon on the live view toolbar to
access the PTZ control panel.
3. To call up the camera setup menu:
From the camera OSD of the DVR, select
Menu.
— or —
From the DVR, select Iris+.
The camera setup menu appears (see “Menu
tree” on page 18 for the menu structure).
4. Select the menu options:
From the TVI recorder (HD-TVI mode): To
select an OSD item, click the directional
buttons up/down. To adjust the value of a
selected item, click the directional buttons
left/right.
From the camera (HD-TVI or Analog mode):
The OSD button is located on the cable
harness. To select an OSD item, push the
Menu button up/down. To adjust the value of a
selected item, push the Menu button left/right.

Installation Guide 17
5. Click Iris+ to enter the submenu or to confirm
the selected item.
6. When the setup is complete, select Exit and
click Iris+ to exit the camera OSD.
Note: You cannot exit the camera setup menu
using the Menu button on the camera.

18 Installation Guide
Menu tree