Interpet Nano STAT User manual

How to install your Nano STAT heater
a. The plug in power supply is not waterproof –this must be mounted so that it cannot fall into the
aquarium. The mains cable must be installed with a drip loop to prevent any water running down the
cable into the plug socket (see image below). Do not operate the heater in an aquarium near or
under an air conditioning unit, in direct sunlight, near a heat source or under a light source which is
on for extended periods of time.
b. The compact Nano STAT heater is designed to fit in a variety of ways inside the aquarium. Ensure
the heater is fully submerged up to the power cord at all times when in use:
In the aquarium - the heater should be installed at an angle, on the side of the aquarium
using the suckers provided (Image 1 below).
In the back filter –where a small aquarium has a back filter the heater can be hidden out of
sight using the suckers to ensure it stays in position (Image 2 below).
Top Tip: If carrying out a water change or before removing the heater from the aquarium, always
turn off the power and let it cool down for approximately 5 minutes.
c. The Nano STAT heaters come complete with an inbuilt thermostat that automatically turns off the
heating element when the aquarium water temperature reaches 25 C. This makes it ideal for
maintaining a stable water temperature all year round, perfect for tropical fish and growing most
tropical plants.
LED Display
Maintenance
Once a year, switch off the heater then wait 5 minutes and remove from the aquarium –
wipe off any dirt, algae or mineral deposits on the heater body with a damp cloth. Do not
use cleaning agents that could enter the aquarium and harm your livestock.
The suckers will eventually lose its suction, when this happens it should be replaced, see
Interpet spare codes below.
Top tip: To optimise adhesion clean the glass before applying the heater suckers.

Troubleshooting
Problem: My Nano STAT is failing to reach 25 C in my aquarium.
Solution 1: Ensure the aquarium is not located in a room that has ambient room temperature of
20 C or less.
Solution 2: Ensure the Nano STAT is not in a slower water movement area, check that the heater is
positioned at an angle (see image 1). This ensures most efficient heater operation.
Solution 3: The Nano STAT is under-powered for your aquarium and you should buy a higher
wattage or an additional aquarium heater. Nano STAT 10w is for aquariums up to 12 litres and the
Nano STAT 25w is for aquariums up to 25 litres.
Spares
Product Spare
Code
10w and 25w Nano STAT Suckers x2
51532
Important information
This unit is for indoor use only –do not use outside.
Do not use this unit if the cable or plug are damaged or appear to be malfunctioning.
Do not use this unit if the plug gets wet.
Dispose of responsibly following instructions from your local authority.
Do not position so that it comes into long-term contact with the aquarium base or sides as
this could lead to damage to the aquarium.
Guarantee
This product is guaranteed against defects in material and workmanship for 12 months from the
date of purchase, under normal usage.
The GUARANTEE DOES NOT APPLY in case of improper use, negligence, lack of maintenance or
accidental damage. This guarantee does not cover the suction cup which is a replaceable part (see
spares above.) If the heater fails due to a manufacturing fault within this period it will either be
replaced free of charge or repaired. Liability is limited to replacement of the faulty product only no
other costs will be reimbursed.
This guarantee is not transferable and does not affect your statutory rights. This guarantee does not
confer any rights other than those expressly set out above.
You can help protect the environment. Please remember to respect the local regulations: hand in
non-working electrical equipment to an appropriate waste disposal centre.
Consumer Advice Contact Details
Interpet Ltd.
Consumer Advice Department
Vincent Lane, Dorking, Surrey RH4 3YX
Fax: [phone] E-mail: customer[email protected]o.uk
www.interpet.co.uk