InterTest CN1 User manual

User Manual
$XWR)RFXV=RRP,3&DPHUDV
Firmware v1.2.0 based
Document Revision 1.3.1b

About This Guide
Disclaimer
© 2013 All rights reserved.
󴎡he trademarks of their respective owners. Information contained in this document may be superseded by updates. No
representation or warranty is given and no liability is assumed by Technology with respect to the accuracy or
use of the information, or infringement of patents or other intellectual property rights. No licenses are conveyed, implicitly
or otherwise, under any intellectual property rights.

1
INTRODUCTION 2
FEATURES 3
INTERFACE AND DIMENSION 4
󰾡4
󰾡󰾡 6
Dimensions 8
SYSTEM FUNCTIONS 11
Overview 11
System Initilize 11
Zooming 11
Focus 11
Preset 12
Auto Patrol 12
Auto Scan 12
Day & Night Setting 12
White Balance 13
AE (Automatic Exposure) 13
AG (Automatic Gain) 14
WDR (Wide Dynamic Range) 14
Noise Reduction 14
Color Enhancement 15
Firmware Functionality 15
SPECIFICATIONS 16
TYPICAL INTEGRATION (PTZ DOME) 18
APPENDIX: UART COMMAND 19
Overview 19
Zoom Position Info. 19
Zoom Ratio and Zoom Position Table 19
ICR Switch On/Off Alarm Receive 20
Block Camera Version Information Inquiry 20
APPENDIX: BUILT-IN PARAMETER PAGE 21
Overview 21
Access built-in PARAMETER PAGE –General Settings 21
Access built-in PARAMETER PAGE –Movement Speed Settings 24
Access built-in PARAMETER PAGE –Preset Table Settings 26
Access built-in PARAMETER PAGE –Movement Speed Settings 27
Get Completed URL for Your Customized IPBC Firmware 29
DOCUMENT CHANGE LOG 30
Document Version 30
10x
18x / 33x

2
This guide is for the use with the Auto focus IP Block Camera using firmware version 1.1.7
or above
The User’s Manual provides functionality and instructions for the ,3FDPHUDs which include the
10[/[/33[based designed product series.
Before Using the IP Block Camera
Check the PC requirements & review the O.S. platform requirement for remote access 
IP block camera products
Having basic knowledge of network setup and configuration will be helpful
Read following important precautionary information
1. &ompatible with software or any 3rd party management software
which fully integrate with API, check the software compatibility in advance if
you desire to use RWKHU software for work.
2. Do not shoot images that are extremely bright (e.g. strong light sources, the sun, etc.) for
long periods of time. Do not use or store the camera in temperature/humidity out of
storage specification. Do not close to generators of powerful electromagnetic radiation
such as radio or TV transmitters. Do not expose where it is subject to fluorescent light
reflections and where it is subject to unstable (flickering, etc.) lighting conditions. Do not
locate where it is subject to strong vibration and where it is subject to radiation from laser
beams.
3. Keep dust & dirt free on surface of lens to guarantee optimized image quality output.
4. Do not apply excessive voltage. (Use only the specified voltage.) Otherwise,
hardware may get any unrecoverable damage.
5. As CMOS image sensors use shutters that capture images line-by-line, there is a slight
time difference between the top and bottom of an image. As a result, images may appear
skewed if the camera is moved. (Commonly called Rolling Shutter)

3
FEATURES
IP Block CamerDVDUH the completed solution to provide real-time HD IP
video with PTZ feature application. It offers highly-integrated block camera solution to take full
advantage of high definition digital video, satisfying most surveillance PTZ-type camera application
with quick, ultra low-cost and easy design-in features.
'esigned with industry state-of-the-art CMOS image sensor
technology, performing high-quality image, full features and reliable AV streaming output; thanks for
up to 33X optical ratio high-end lens, no matter darkness or high dynamic range environment, RXUFDPHUDV
can always enable optimized image for surveillance purpose.

4
INTERFACE AND DIMENSION
10[
Connector and Pin-define
Name:
CN1
Type:
16-pin 1.25mm pitch female wafer
Definition:
Pin Definition
Pin_1
RS-485 +
Pin_9
GND
Pin_2
RS-485 -
Pin_10
Line_Out
Pin_3
UART_Rx
Pin_11
Line_In
Pin_4
UART_Tx
Pin_12
GND
Pin_5
External_IR_Sync._In
Pin_13
Network_Tx+
Pin_6
External_IR_Sync._Out
Pin_14
Network_Tx-
Pin_7
DC6~12V Input +
Pin_15
Network_Rx+
Pin_8
Pin_16
Network_Rx-
Name:
System reset bottom
Type:
Tact switch
Definition:
Reset system as factory default
1 16

5
Name:
SD slot
Type:
microSD/SDHC
Definition:
Compatible micro- SD or SDHC card with class4 or class10, supporting up to 32GB capacity
Locations of Controls
Front:
Bottom:
** When a tripod screw is used, please use 1/4 inch screw to attach it to the
module; also, please be sure to attach the tripod screw securely
Lens
Tripod screw hole
18x / 33x

6
[ / 3[
Connector and Pin-define
Name:
CN1
Type:
16-pin 1.25mm pitch female wafer
Definition:
Pin Definition
Pin_1
RS-485 +
Pin_9
GND
Pin_2
RS-485 -
Pin_10
Line_Out
Pin_3
UART_Rx
Pin_11
Line_In
Pin_4
UART_Tx
Pin_12
GND
Pin_5
External_IR_Sync._In
Pin_13
Network_Tx+
Pin_6
External_IR_Sync._Out
Pin_14
Network_Tx-
Pin_7
DC6~12V Input +
Pin_15
Network_Rx+
Pin_8
Pin_16
Network_Rx-
Name:
System reset bottom
Type:
Tact switch
Definition:
Reset system as factory default
Name:
Video Out
Type:
2-pin 1.25mm pitch wafer
Definition:
Composite video output (D1 resolution)
1 16

7
Name:
SD slot
Type:
microSD/SDHC
Definition:
Compatible micro- SD or SDHC card with class4 or class10, supporting up to 32GB capacity
Locations of Controls
Front:
Bottom:
** When a tripod screw is used, please use 1/4 inch screw to attach it to the
module; also, please be sure to attach the tripod screw securely
Lens
Tripod screw hole
18x / 33x

8
Pin Description
Pin_1 ~ Pin_2:
RS-485 connection interface, controlling external motor module pan/tile movement
Pin_3 ~ Pin_4:
UART connection interface, communication with external camera for smart IR and
ICR trigger; built-in VISCA protocol as default
Pin_5:
To receive high/low signal from external IR lighting module to trigger ICR switch at the
same time
Pin_6:
To trigger with high/low signal to external IR lighting module
Pin_7 ~ Pin_8:
DC + voltage input (6~12Vdc)
Pin_9:
DC voltage ground (or DC –voltage input)
Pin_10 ~ Pin_12:
Bi-directional audio connection with external speaker and microphone
Pin_13 ~ Pin_16:
Network signal

9
Dimension –10[
Front Top
Right
Rear Left
Bottom

10
Dimension –[ / 3[
Front Top
Right
Rear Left
Bottom

11
SYSTEM FUNCTIONS
Overview
a professional IP block camera product, integrating superior HD CMOS sensor,
high-quality auto-zooming lens and reliable streaming-application encoder design; it also equipped
with state-of-the-art ISP (Image Signal Processing) engine to
optimize video as clear, crystal at any surveillance environment
System Initialize
When module is powerHG on, it will automatically manipulate system initialization including
zoom and focus of lens
Zooming
'esigned with variety high-quality optical zooming lens (from 10X to 33X), user can
easily control zooming function via variety clients, including web browser, management software,
joystick and mobile APP. It allows you to control zooming:
10X optical lens, f=5.1 mm(WIDE) to 51 mm(TELE), F1.6 to F1.8
18X optical lens, f=4.7 mm(WIDE) to 84.6 mm(TELE), F1.6 to F2.7
33X optical lens, f=4.5 mm(WIDE) to 148.5 mm(TELE), F1.6 to F5.0
The horizontal angle of view on FDPHUDV approximately
10X: 54.0 º (wide end) to 4.9 º (tele end)
18X: 54.8 º (wide end) to 3.4 º (tele end)
33X: 62.5 º (wide end) to 2.5 º (tele end)
Focus:
The minimum focus distance is 150 mm at the optical wide end and 1,000 mm at the
optical tele end on MANUAL FOCUS mode, 1,000 mm at the optical wide end and 5,000 mm at the
optical tele end on AUTO FOCUS mode, and is independent of the digital zoom.
6upports manual focus and auto focus modes on variety client control interface

12
Manual Focus Mode
The lens focus can be adjusted manually by slide bar on control panel of web client
Focus adjustment speed can also be selected by client UI
Auto Focus Mode
An AF icon is located on control panel to allow user enable or disable auto focus
function;
The Auto Focus (AF) function automatically adjusts the focus position to maximize
the high frequency
content of the picture in a center measurement area, taking into consideration the
high luminance
and strong contrast components.
Preset:
Up to 256 preset points can be freely defined by user with configurable pan/tilt position, zoom ration
and focus stop; user can easily manipulate P/T/Z/F control by control panel, then click “SET”to
memorize specific preset points, or ”GO”to reach desired preset destination.
Auto Patrol:
$llows user to combine several preset points as patrol tour which can automatically handle
preset “GO”by pre-defined sequent order and dwell time
Up to 24 sets patrol paths can be independently configured, each supports maximum 256 preset
points inside.
Auto Scan:
Auto Scan stands can automatically move horizontally between two pre-defined specific
preset points; user can set left and right boundary on UI and click AS icon on panel to start this
feature.
Day & Night Setting:
B series supports variety day/night modes:
Force to Day Mode
The built-in ICR will be always enabled to filter IR long-wave light and sensor is in
color mode

13
Force to Night Mode
The built-in ICR will be always disabled to allow all light input, color mode or
black/white mode can be selectable
Auto Mode (AE) Mode
Day or night mode will be decided by system analysis via entire captured image, user
can also adjust “From day to night”and “back to day”trigger level for specific
environment.
**A luminance measured value is displayed on UI real-time for adjust reference
External Trigger Mode
&an accept external light sensor trigger to switch day or night mode (eg. An
external light sensor equipping with IR LED can change ICR to night mode for IR
illumination at night time.
**The pin5 & pin6 can connect with external signal input by 5V / 0V high / low voltage
level
&an accept external alarm from external light sensor by VISCA
command to switch between day and night modes; the acceptable VISCA command,
please refer to Appendix “ICR Switch On/Off Alarm Receive”section.
Day Time Profile / Night Time Profile
User can independently define all image parameters on “Day Time Profile”and “Night
Time Profile”; the profile switching depends on Day/Night setting.
White Balance:
6upports white balance with following modes:
AWB (Auto White Balance)
This mode is automatically to compute white balance by system via color information
from captured image; B series performs the proper value using color temperature
radiating from a black subject based on a range of values from 2,800K to 10,000K
Manual WB Lock
This mode is to manually keep white balance at fixed value that is adjustable and
defined by the request of users with the white color definition (eg. User can shoot the
defined”white”full image, then push “Manual WB Lock”to enable this feature on UI).

14
AE (Automatic Exposure):
6upports following AE (Auto Exposure) control modes:
AE Range Limit
This mode can define upper and lower exposure limit levels to allow system to
automatically adjust image exposure within defined EV range
**Upper limit range from 0.0EV to +2.0EV; lower limit range from 0.0EV to -2.0EV
AEC(Auto Exposure Control) mode
AEC mode can handle image exposure with maximum shutter time define; disable
AEC mode is to keep shutter at fixed value
Supported shutter time on B series includes up to 13 steps:
Shutter time
50Hz
60Hz
1/3
1/4
1/6
1/8
1/12
1/15
1/25
1/30
1/50
1/60
1/100
1/120
1/200
1/250
1/400
1/500
1/800
1/1000
1/1600
1/2000
1/3200
1/4000
1/6400
1/8000
1/15000
1/15000
**At AEC mode on, exposure can be set by max shutter time from 1/30 ~ 1/500 or
1/4~1/500; when AEC mode off, user can select fixed shutter within range from 1/30 ~
1/15,000 or 1/4~1/15,000
AG (Automatic Gain):
The gain(digital and analog gain) can be configured within B series UI
AGC(Auto Gain Control) mode
This mode can allow system automatically adjust gain level by setting maximum gain
level value.
Disable AGC, also say ”Manual Gain”, is to keep system gain level at a specific value.
**Gain level range from 2X to 128X

15
WDR (Wide Dynamic Range):
The wide dynamic range can be set to be disable or enable with 3 different intensity
**WDR level supports low, medium and high 3 levels setting
**󰾡 󰾡󰾡support dual-exposure WDR where image are
produced by combining long-exposure and short-exposure one to obtain an high dynamic
range image in which portions ranging from dark to light can be well-recognized
Noise Reduction:
The NR feature eliminates noise on image to provide clearer image quality
Auto mode
Allow system to manipulate noise reduction automatically.
Manual mode
User can also manually decide noise reduction level at fixed level value.
**A slide bar from value 1 to 254 is adjustable under this mode
Color Enhancement:
$llows to enhance shoot image with following parameters:
Brightness
An adjustable slide from 0~255 can enrich or downgrade image brightness
Contrast
An adjustable slide from 0~255 can enrich or downgrade image contrast
Saturation
An adjustable slide from 0~255 can enrich or downgrade image saturation
Sharpness
An adjustable slide from 0~255 can enrich or downgrade image sharpness
Flip
Enable flip can rotate image to 180 degree vertically
Mirror
Enable flip can rotate image to 180 degree horizontally
18x and 30x

16
Firmware Functionality:
Refer to “FIRMWARE MANUAL”document to get detail functionality description and example.

17
SPECIFICATIONS
Model
1[ [ 33[
IMAGE
Image Sensor
1/3” type CMOS
Max. Resolution
2,048 x 1,536 (H x V)
Lens
10X Optical Zoom Lens: f=5.1 mm (WIDE) to 51 mm (TELE), F1.6 to F1.8
18X Optical Zoom Lens: f=4.7 mm (WIDE) to 84.6 mm (TELE), F1.6 to F2.7
33X Optical Zoom Lens: f=4.5 mm (WIDE) to 148.5 mm (TELE), F1.6 to F5.0
Angle of View
(Horizontal)
10X: 54.0º(wide end) to 4.9º(tele end)
18X: 54.8º(wide end) to 3.4º(tele end)
33X: 62.5º(wide end) to 2.5º(tele end)
Focus Range
Manual focus: 0.15M ~ Infinite (WIDE), 1.0M ~ Infinite (TELE)
Auto focus: 1.0M ~ Infinite (WIDE), 5M ~ Infinite (TELE)
Min. Illumination
0.1 lux @ F1.2
Shutter Speed
Auto / Manual, 1/3~1/15000 or 1/4~1/15000 Selectable
Image
Enhancement
Brightness, Contrast, Saturation, Sharpness, Flip, Mirror, BLC, Privacy mask
White Balance
Auto (Auto tracing white balance from 2800 to 10000K) / One-push WB
Gain
Auto / Manual
Wide Dynamic
Range
Digital WDR
Dual-exposure WDR
Noise Reduction
Auto / Manual
Day / Night
Control
Built-in ICR, supporting independent configurable Day/Night profile / external light sensor
control supported
NETWORK
Video
Compression
Motion JPEG, MPEG-4, H.264 High Profile
Max. fps @
Resolution
20fps@3MP, 30fps@HD-1080p
Audio
Compression
G.711(u-law & a-law), G.726, AAC
Streaming
Multiple Stream: Support up to 4 Independent Streams with ROI(Region of Interest)
Feature, Controllable Frame rate and Bandwidth CBR/VBR
Bit Rate
M-JPEG/VBR Mode: 5 Video Quality Level Selectable, MPEG-4/H.264 CBR Mode: 1
M~12 Mbps

18
Security
Password Protection, IP Address Filtering, User Access Privilege
Protocol
TCP/IP, UDP, DHCP, HTTP, HTTPS, DNS, DynDNS, NTP, FTP, SMTP, UDP, RTP,
RTSP, RTCP, 3GPP, UPnP, IPv4, SAMBA Client(NAS)
API
ONVIF, CGI
Intelligent Video
Motion detection
Alarm Trigger
Periodical Timer, Intelligent Video, Network loss
Alarm Action
Intelligent Video, File Upload via FTP and E-mail, Notification via E-mail, File Recording
to SD Card, Remote FTP or Remote NAS
Video Buffer
24MB Max.
Configuration
EtroScan™ Utility, Web UI
Web Client
Microsoft IE 8.0 or above, Mozilla Firefox, Google Chrome
PTZ
Preset Point
Max. 256 preset points
Auto Focus
Auto / Manual mode selectable
Auto Patrol
Max. 24 patrol paths, each supporting up to 256 preset points with configurable
sequence and dwell time
Auto Scan
Configurable right / left boundary and speed level
GENERAL
I/O_CN1
16-pin female wafer (1.25mm pitch)
I/O_Reset
Tact switch
I/O_SD Slot
microSD/SDHC supporting up to 32GB
Power Input
Power
Consumption
6Vdc ~ 12Vdc input
B10: 5 Watt (motor active) / B20: 5.1 Watt (motor active) / B33: 5.3 Watt (motor active)
Operation Temp.
/ Humidity
–5 °C ~ +60 °C (23 °F to 140 °F) / 20% ~ 80%
Storage Temp. /
Humidity
–20 °C ~ +60 °C (-4 °F to 140 °F) / 20% ~ 95%
Anti-vibration
5 Hz to 50 Hz 4.14 m2/s3
50 Hz to 100 Hz –36 dB/oct
Dimension
B10: 38.6 (W) x 45.7 (H) x 61.7 (D) mm
B20 / B33: 50 (W) x 60 (H) x 89.2 (D) mm
Weight
B10: 103 g
B20: 191 g
B33: 210 g