D-MAX DMS-200 User manual

MINISPEEDDOMECAMERA
MINI SPEED DOME CAMERA
USER MANUAL
DMS-200
DMS-200Se

TABLE OF CONTENTS
1. CATION ------------------------------------------------------- 3
2. INTRODUCTION OF PRODUCT -------------------------------5
1). DESCRIPTION AND FEATURES -----------------------------5
2). INSTALLING AND CONNECTING ---------------------------- 6
2-1. NAME AND FUNCTION OF EACH PART -------------------6
2-2. INSTALLATION --------------------------------------7
2-3. CONNECTION DIAGRAM
--------------------------------8
3. DIRECTIONS FOR USE -----------------------------------------9
1). DIP SWITCH SETTING ---------------------------------------9
2). HOW TO CHANGE PROTOCOL
-------------------------------10
3). HOW TO SET ADDRESS DIP SWITCHES ----------------------11
4). HOW TO USE OSD MENU ----------------------------------12
4-1. HOW TO CONTROL OSD MENU --------------------------12
4-2. FUNCTIONAL DESCRIPTIONS ON EACH MENU ------------13
4-3. SETTING FUNCTIONS BY KEYBOARD---------------------23
4-4. OSD MESSAGE DESCRIPTION
---------------------------27
4. TROUBLE SHOOTING ------------------------------------------29
5. ASSEMBLES----------------------------------------------------30
6. CONFIGURALTION ---------------------------------------------31
7. SPECIFICATIONS ----------------------------------------------33

1. CAUTION
Thank youfor purchasing mini speed dome camera DMS-200.
Please operate the product after being fully aware of the manual.
Pease contact us if you have any queries or face any problems.
DO NOT CONTROL PAN, TILT BY FORCE
Do not move the inside Pan/Tilt motor by force
after removing dome cover.
It can cause damages.
HANDLE WITH CARE OF CAMERA LENS AND DOME
Be careful of handle with dome cover
Please use a soft fabric due to a scratch when you
clean the cover.
EXTERNAL SHOCK
Damages can be occurred through the carelessness
Or shock when you take out the module.

CAUTION IN USE.
Do not disassemble the unit and put alien substances in the unit.
It can cause troubles.
Ensure power switch-off before the installation.
Ensure power switch-off and check the voltage the camera before the installation.
Do not give the unit a shock and an operation.
Giving a strong shock or an excessive power on the button, terminal can cause troubles.
This product has been designed and manufactured in accordance with the harmonized European
standards, following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC(EN61000-3-2:1995, EN61000-3-3:1995,
EN50081-1:1992, EN50082-1:1997)
This devise complies with part 15 of the fcc rules operation is subject to the following two
conditions: (1) This device may not cause harmful interference and (2) This device must accept
any interference received including interference that may cause undesired operation
※ Components
- Mini Speed Dome Camera 1 Pcs
- Adaptor ( AC24V 2.5A ) 1 Pcs
- Manual 1Pcs

2. INSTRUCTION OF PRODUCT
1). DESCRIPTION AND FEATURES
- Description -
This camera has been designed elegantly for buildings, department stores that need to be
in harmony with the interior as a mini speed dome camera, including various observation
functions. It moreover is effective for true Day & Night.
- Features -
High magnification zoom lens
Max 192 times zoom
(optical x12 zoom, digital x16 zoom)
Horizontal resolution min. 600 TVL
Color: 600 TVL, B/W: 700 TVL
horizontal resolution
Low light and Day & Night
The result of improving sensitivity
0.00003Lux (DSS Control)
ICR Day & Night allows the filter to change
B/W mode in the night.
Additional functions
PTZ trace:
Memorize P/T/Z move for 120 seconds then
operate the registered trace.
Auto swing:
Repeat pan and tilt between two preset
positions.
Group:
12 Preset positions are chained in one Group.
(Max 12 Groups available)
Tour:
Max 12 Groups are bound.
410k Pixel CCD CAMERA
SONY CCD chip with high resolution and low
illumination condition.
250 Preset positions
A maximum of 250 preset positions can be
programmed. The preset function enables to set
where you want on monitor at any time.
4ch alarm inputs
It can be directly connected to sensor and used
with presets owing to built-in 4-channel
sensor input terminals.
It can be also operated together with other
equipment owing to built-in alarm output.
Auto Tilt move
The unit can track the object moving automatically
until 180° in vertical.
OSD (On Screen Display)
Provides character information displayed on the
monitor, such as the camera ID address,
camera name, preset number, sequence status,
and sets various functions of camera easily on
the OSD menu screen.
Privacy Zones
For the privacy, it can be programmed for
masking zone up to 8 locations on the
OSD menu screen.

2) INSTALLATION AND CONNECTION
2-1. NAME AND FUNCTION OF EACH PART
104 ¢
BUBBLE
CAMERA
HOUSING
P/T
CAMERA
CONNECT
COVER
CAMERA
BODY
CAMERA
BODY
COVER
125 ¢
BUBBLE
Indoor Outdoor

2-2. INSTALLATION
Indoor
Make 4 holes after attaching
ceiling guide where the
camera is set.
Take apart 4 bands of camera body
cover
Set up DIP switch
(Reference to XXP)
Connect with cables.
Tighten 4 screws. Attach the camera
body cover
Completion
Take out the cables
from the ceiling.

Outdoor
Unscrew the 4 bolts of the bubble cover then separate the camera housing.
Connect the power, data, and video cables at
Connect Cover, then set DIP SWITCH. (Go to
at page xx)
Recombine the housing
and attach the bracket.

2-3. CONNECTION DIAGRAM
Indoor
AC24V/more than 1A
VIDEO IN AUDIO IN
CAMERA 1~128
DC JACK
RS-485 Sensor 1
4 ALARM INPUT
VIDEO INPUT Sensor 4
CAMERA 129
~
CAMERA 255
Violet(N/O)
Gray(COM)
Black(GND)
Brown(CH1)
Red(CH2)
Yellow(CH3)
Green(CH4)

Outdoor

3. DIRECTIONS FOR USE
1) DIP SWITCH SETTING
-TERMINALATION RESISTOR (DIP S2/SW1)
~Turn the last camera on the data line as a
switch to turn on/off the terminal resistor on.
Turn the DIP SW of some of the farthest
cameras on in the case of the data lines
distributed to several directions.
* The first default is off.
-ADDRESS/ INITIAL SELECT (DIP S2/SW2)
~Set ADDRESS DIP SW in the status of ADDRESS
(*Reference to next page*)
(.*** The first default is ADDRESS.**)
-Set the communication speed and Protocol
(Demand for the technical inquiry) up in the
state of the INITAIL.
-Select PAL / NTSC system. .(DIP S2/SW 3)
-POWER ON/OFF (DIP S2/SW 4)
Set DIP SW only in the status of Power off.
Then turn on the power after setting DIP SW.
<S2>
<S1>
It shows the status of Power
On/Off. Green LED is On while
power is alive. In the status of
operation, red LED is off.
Set the camera numbers in the state of
ADDR, set communication speed, protocol
in the state of INIT.
-This part is each address of camera.-
Indoor
Outdoor

2) HOW TO CHANGE PROTOCOL
Set up this part.
The switch that selects Protocol. The switch that selects Baud Rate.
.
Change No.3 at S2 to INIT if want to change Protocol.
① Please make Power off.
② Switch Protocol that wants to change on as above table.
③ Make Power on, then set Protocol and Baud rate are appealed.
④ Make Power off, if every setting is right. Then it is done.
⑤ Change No.3 of S2 to ADDR before Power on, then make Power on after setting the
address of the camera.
⑥ Try it again with the information as above the table, if something is wrong.

3) HOW TO SET ADDRESS DIP SWITCHES
Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program.
RX NO
DIP SWITCH (HEX) RX NO
(DEC)
DIP SWITCH (HEX)
1 2 3 4 5 6 7 1234 5 6 7
1 ON OFF OFF OFF OFF OFF OFF 33 ON OFF OFF OFF OFF ON OFF
2 OFF ON OFF OFF OFF OFF OFF 34 OFF ON OFF OFF OFF ON OFF
3 ON ON OFF OFF OFF OFF OFF 35 ON ON OFF OFF OFF ON OFF
4 OFF OFF ON OFF OFF OFF OFF 36 OFF OFF ON OFF OFF ON OFF
5 ON OFF ON OFF OFF OFF OFF 37 ON OFF ON OFF OFF ON OFF
6 OFF ON ON OFF OFF OFF OFF 38 OFF ON ON OFF OFF ON OFF
7 ON ON ON OFF OFF OFF OFF 39 ONONONOFF OFF ON OFF
8 OFF OFF OFF ON OFF OFF OFF 40 OFF OFF OFF ON OFF ON OFF
9 ON OFF OFF ON OFF OFF OFF 41 ON OFF OFF ON OFF ON OFF
10 OFF ON OFF ON OFF OFF OFF 42 OFF ON OFF ON OFF ON OFF
11 ON ON OFF ON OFF OFF OFF 43 ON ON OFF ON OFF ON OFF
12 OFF OFF ON ON OFF OFF OFF 44 OFF OFF ON ON OFF ON OFF
13 ON OFF ON ON OFF OFF OFF 45 ON OFF ON ON OFF ON OFF
14 OFF ON ON ON OFF OFF OFF 46 OFF ON ON ON OFF ON OFF
15 ON ON ON ON OFF OFF OFF 47 ONONONON OFF ON OFF
16 OFF OFF OFF OFF ON OFF OFF 48 OFF OFF OFF OFF ON ON OFF
17 ON OFF OFF OFF ON OFF OFF 49 ON OFF OFF OFF ON ON OFF
18 OFF ON OFF OFF ON OFF OFF 50 OFF ON OFF OFF ON ON OFF
19 ON ON OFF OFF ON OFF OFF 51 ON ON OFF OFF ON ON OFF
20 OFF OFF ON OFF ON OFF OFF 52 OFF OFF ON OFF ON ON OFF
21 ON OFF ON OFF ON OFF OFF 53 ON OFF ON OFF ON ON OFF
22 OFF ON ON OFF ON OFF OFF 54 OFF ON ON OFF ON ON OFF
23 ON ON ON OFF ON OFF OFF 55 ONONONOFF ON ON OFF
24 OFF OFF OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF
25 ON OFF OFF ON ON OFF OFF 57 ON OFF OFF ON ON ON OFF
26 OFF ON OFF ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF
27 ON ON OFF ON ON OFF OFF 59 ON ON OFF ON ON ON OFF
28 OFF OFF ON ON ON OFF OFF 60 OFF OFF ON ON ON ON OFF
29 ON OFF ON ON ON OFF OFF 61 ON OFF ON ON ON ON OFF
30 OFF ON ON ON ON OFF OFF 62 OFF ON ON ON ON ON OFF
31 ON ON ON ON ON OFF OFF 63 ONONONON ON ON OFF
32 OFF OFF OFF OFF OFF ON OFF 64 OFF OFF OFF OFF OFF OFF ON
-No.1 is changed to No.64 and the last No.64 is changed No.128 when No.7 DIP SW is on.
-No.1 is changed to No.129 when No.7 DIP SW is off and No.8 DIP SW is on.
-No.1 is changed to No.193 and user can set up to maximum 255 ADDRESS when No.7, 8 DIP SW
are on.

4) HOW TO USE OSD MENU
4-1. HOW TO CONTROL OSD MENU
OSD (ON SCREEN DISPLAY) CONTROL
It is the function to call up the Menu
＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera
up by the menu, but also set them up by shortening keys. (Refer to 4-3 content)
ACCESSING OSD MENU
①
②
●The menu is displayed on the screen with the key tone when user presses No.1 and
menu key.
●OSD Menu Control Up, Down, Right and
Left moving of Cursor like under pictures
●Cancellation of OSD menu
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE

4-1. FUNCTIONAL DESCRIPTIONS ON EACH MENU
1. ID SET.
This function is to set
camera ID up to 16
letters on the monitor.
User can choose letters
that they want, if user
control a joystick up /
down / right / left, and
user can reselect the
previous letters, if user
presses Z/I, Z/O or turn the head of the joystick to right/left
2. OSD DISPLAY.
Set up whether user sets ID and STATUS to
display on the
screen in normal operating.
●ID + Status: ‘ID’ and ‘Status’ displayed on the
screen
●ID only: Only ‘ID’ displayed on the screen
●Status only: Only ‘Status’ displayed on the
screen
●All off: Nothing displayed on the screen
3. H-V REVERSE
Set up H-V reverse mode.
●Normal
●H-REV : You can flip the picture horizontally on
the screen.
●V-REV : You can flip the picture vertically on the
screen.
●HV-REV : You can flip the picture horizontally
and vertically on the screen.
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4. AGC Control : Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7. Brightness : 09
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2.OSDDisplay. :ID+Status
3.H-VReverse. :Normal
4. AGC Control : Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7. Brightness : 09
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7. Brightness : 09
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE

4. AGC CONTROL
AGC(Automatic Gain Control)- It adjusts the
amount of video amplification to maintain a full 1-
volt peak-to-peak video signal output automatically.
▶Low, Medium, Max
5. SHUTTER SPEED
As a setting shutter speed mode, it can be
distinguished a fast moving subject easily by
means of shutter speed up.
※Attention-The illumination of the camera
decreases if shutter speed is up.
※The state of first default is ‘AUTO’.
※It can be worked in the state of Flickerless ‘off’
▶Range : Auto, 1/125, 1/250, 1/500, ---
1/120000
6. SHARPNESS LEVEL
Compensation of the shape of a subject
▶Range : 0 ~ 10, Default : 6
7. BRIGHTNESS
Control brightness of a screen.
The screen gets dark because an iris is closed as
the numerical value is low, whereas the screen
gets bright because an iris
is opened as the numerical value is high.
▶Range: 0~19, Default: 9
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4.AGCControl :Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7. Brightness : 09
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4. AGC Control : Medium
5.Shutterspeed. :AUTO
6. Sharpness level : 06
7. Brightness : 09
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4. AGC Control : Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7. Brightness : 09
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4. AGC Control : Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7.Brightness :09
8.Flickerless :OFF
9. DNR Control : Medium
- NEXT MENU PAGE

8. FLICKERLESS
Tremble on the screen is removed in the state of
FLICKERLESS ‘ON’, the shutter speed, at the
same time, is fixed in 1/120sec in NTSC and in
1/100sec in PAL.
▶Off, Manual, On
9. DNR Control
It can remarkably reduce noise of minimum
illumination by super noise removable
technique and also file size becomes smaller while
DVR is being recorded by the effective reduction of
noise.
▶Off, Low, Medium, Max
10. BACK LIGHT
This camera is designed so that it delivers a
distinctive subject and background at the same
time, even when the subject is in backlight, unlike
conventional cameras, by adopting a proprietary
DSP chip.
.Please select a suitable mode below them (The
Set Back Light Mode will be automatically changed
by the selection)
▶Off, WDR MODE, HLC MODE, BLC MODE
WDR : When there are both bright and dark areas at the same time, this mode makes both
areas distinctive.
BLC : Enables a user to directly select a desired area from a picture, and to view the area more
clearly..
HLC(High Light Compensation) : If there is a high light installed in dark environment such as
an apartment parking garage or gas station entrance, removing the high light makes it possible
to view car license plates efficiently
OFF : Deactivates the BACKLIGHT function.
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4. AGC Control : Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7. Brightness : 09
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :
Press F/F Key
2. OSD Display. : ID + Status
3.H-VReverse. :Normal
4. AGC Control : Medium
5. Shutter speed. : AUTO
6. Sharpness level : 06
7. Brightness : 09
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10.BackLight :WDRMode
11. Set Back Light Mode
12. White Balance : Auto
13.FocusMode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE

11. SET BACK LIGHT MODE
▶WDR MODE
- Limit: Adjust the WDR Sensitivity by selecting
Low or Max
- Level: Adjust the WDR Brightness by controlling
0~15.
▶HLC(High Light Compensation)MODE
- Limit: Adjust the HLC Sensitivity by selecting Low,
Medium or Max
- Level: Adjust the WDR Brightness by controlling 0~15.
- This Function only operate in nighttime.
▶BLC MODE : Select BLC mode or BLC Set area mode by using the joystick.
- BLC Level: Adjust the BLC Sensitivity by selecting Low, Medium or Max
- BLC Set AREA (Press F/F): Set BLC area location and size
- Select F/F button, and set the BLC area by using the joystick, and set are size by using Z/I,
Z/O buttons. (The monitor shows as Exit BLC set(Press F/N)
After complete all setup, press F/N button, and then move to RETURN MENU PAGE. It is
automatically saved.
12. WHITE BALANCE
It prevents from that white color is changed as
illumination.
▶Auto, Indoor, Outdoor
13. FOCUS MODE
Change Focus Mode to hand-worked or auto.
▶OneShot : Auto Focusing mode works during
non-working
after zoom is worked.
▶Auto: It adjusts the focus automatically as it
monitors the screen.
▶Manual: User can control the focus by hand-
worked.
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13.FocusMode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13.FocusMode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE

14. ZOOM MAX Limit
It is used when user corrects and limits the
extensional range
of the focus as a function to set the maximum
value of zoom.
▶Off,
▶12x zoom : 24X ~ 192X
15. DSS CONTROL
An object becomes clear as the field value gets
higher in
illumination, whereas a moving object becomes
dim.
▶Range : Off, 2 ~ 512 fields
16. DAY& NIGHT
The function is used to distinguish an object clearly
in the dark condition.
▶ Auto-Low: This mode is worked automatically
according to sensitivity, if the sensitivity is low
▶ Auto-Hi: This mode is worked automatically
according to sensitivity, if the sensitivity is high.
▶ On: B/W mode ▶ Off: color mode
※ Auto-low mode will be changed from B/W
to color fast as illumination.
17. STABILIZE On/Off
There is some tremble as zoom magnification is
high, the function can compensate the tremble.
▶On / Off
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13.FocusMode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13.FocusMode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13.FocusMode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
-
NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13.FocusMode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16.Day&Night :Auto+Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
-
NEXT MENU PAGE

18. SELECT ALARM
Set alarm mode you want to use.
▶Sensor / Motion
19. Motion Detection
If you want to use motion detection, set “On” mode.
And then set area where you want to detect by
using F/F key.
• How to set area
- Area size can be controlled by using Z/O
and Z/I key
- Area position can be controlled by using
joystick.
20. PRESET SET & RUN PAGE
It is a function to set and operate Preset, Group,
Tou r.
User can see the screen when moves the joystick
to Right/Left after fixing the cursor on the menu.
<<PRESET SETUP PAGE>>
①Preset set CH :
User can set Preset No. and title on this menu.
- Preset No. set : Set it by moving the joystick to
Right/Left
- Preset title set : User can see the menu “SET ID” when press F/F key after setting Preset No
◄◄ CAMERA SETUP p3 ►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p3 ►►
18.SelectAlarm :Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p3 ►►
18.SelectAlarm :Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE