INVENTOR DRVI32-09WF User manual

MODELS:
DRVI32-09WF
DRVI32-12WF
DRVI32-18WF
DRVI32-24WF
REMOTE CONTROLLER
AIR CONDITIONING SYSTEMS
• USER’S MANUAL
• MANUAL UTILIZATORULUI

WARNING:
·If the supply cord is damaged, it must be replaced by the manufacturer,its service agent or
similarly qualified persons in order to avoid a hazard.
·This appliance can be used by children aged 8 years and above and persons with reduced
physical, sensory or mentao capabilities or lack of experience and knowledge if they have
been given superivision or instruction concering use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
·The wiring method should be in line with the local wiring standard.
user maintenance shall not be made by children without supervision.
All the cables shall have got the European authentication certificate. During installation, when the
·connecting cables break off, it must be assured that the grouding wire is the last one to be broken off.
The explosion-proof breaker of the air conditioner should be all-pole switch. Distance between its two
contacts should not be no less than 3mm. Such means for disconnection must be incorporated in the
·
·Make sure installation is done according to local wiring regulation by professional persons.
·
·A leakage explosion-proof breaker must be installed.
Make sure ground connection is correct and reliable.
Read the precautions in this manual
carefully before operating the unit. This appliance is filled with R32.
Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacturer.
·
Keep thismanualwhere the user can easily nd it.
The appliance must be stored in a room without continuously operating ignition sources (for
example: open flames, an operating gas appliance or an operating electric heater).
Do not pierce or burn.
·
·Be aware that refrigerants may not contain an odour.
·The appliance must be installed, operated and stored in a room with a floor area larger than
3 .
·
·Do not use a refrigerant other than the one indicated on the outdoor unit(R32) when installing,
moving or repairing. Using other refrigerants may cause trouble or damage to the unit, and
personal injury.
wiring.
Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference
This appliance is filled with R32.
001

1
1
2
1
1
1
Contents
PARTS AND FUNCTIONS
OPERATION
INDOOR UNIT INSTALLATION
MAINTENANCE
CAUTIONS
TROUBLE SHOOTING

Parts and Functions
Indoor Unit Remote controller
Outer side of the controller
89status
10
711
12
TIMER
13
611. FAN SPEED display
SWING display
Swing up/down display
swing left/right display
TIMER ON display
TIMER OFF display
CLOCK display
12.
5
14
413.
15
Display board 12
35
316
1Signal receiver hole
Ambient temp.display
When receiving the remote
4614. FAN button
2SMART 17
24HEAT display
1POWER
control signal, display the set
temperature.
5HEALTH display
3COOL display 6DRY display
1. POWER button
2. DRY button
Used to set DRY operation.
COOL button
Used to set COOL operation.
TEMP button
used to change setting
temperature
Actual inlet grille may vary from the one shown in the
manual according to the product purchased 3.
4.
Outdoor Unit
NOTE:
4
OUTLET CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSEINLET
1
5. ON / OFF button
6. Display of each function
7. Operation mode display
8. WIFI and CLOCK display
9. TEMP display
10. Humidity display
15. QUIET button
16. HEAT button
17. SMART button
Used to set SMART
operation. (This function
is unavailable on some
models.)
a. Humidity display is unavailable on some models
b. If the model you buy has a WIFI function, press the“ON/OFF”
button for 5s to emit the WIFI binding signal. Once in the
binding mode, the APP will show how to bind.
Outlet
Display board
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
(adjust left and
ow)
Vertical blade
Emergency
Switch
right air fl
Inlet
Air Purifying Filter
(inside)
Inlet grille
Anion generator
(inside)
(inside)

Operation
18. TIMER button
19. CLOCK button
10 ºC button
special heating set
function: 10 degree
heating maintaining
(valuable for RS)
Clock set
20. 1Press CLOCK button,
2Press “+” or “-” to set
correct time.
Each press will increase or
decrease 1min. If the button is
kept pressed, time will change
quickly.
23 24
22 25 3
21 26 FAN MODE
20 27
19 28
18 29 press APPLY, “AM” and
starts working.
30
Note: Note:
The distance between the signal transmission head and
the receiver hole should be within 7m without any obstacle
change-over wireless telephone is installed in the type
in receiving the signals, so the distance to the indoor unit
should be shorter.
Full display or unclear display during operation indicates the
batteries have been used up. Please change batteries.
If the remote controller can’t run normally during operation,
please remove the batteries and reload several minutes later
Hint:
Remove the batteries in case unit won’t be in usage for
a long period.
2
21. HEALTH button
22. FAN MODE button
23. SWING up/down button
24. SWING left/right button
25. SLEEP button
26. HEALTH AIRFLOW button
27. LIGHT button
Control the lightening and
extinguishing of the indoor
LED display board.
28. CODE button
A-b yard
29. APPLY button
30. °F/°C button
FAN MODE
Press “HEALTH”+“HEALTH AIRFLOW” simultaneously can
set and cancel the “LOCK” function ( )

nnooiittaarreeppOO
QUIET OperationQUIET Operation nnooiittaarreeppOOYYRRDDddnnaaTTAEH, AEH,LOOC LOOC
1Unit start.
2Select operation mode.
Press the COOL button on
the remote control.
SMART QUIET Operation SMART
POWER POWER
TTEEIIUUQQ
Press the HEAT button on the remote control.
You can use this function when silence is needed for rest or
reading.
For each press, is displayed Air conditioner starts
QUIET function operation. In QUIET operation mode, fan
speed automatically takes low speed of AUTO fan mode.
Press QUIET button again, disappears, the operation
stops.
Press the DRY button on the remote control.
3
1. In DRY mode, when room temperature becomes
lower than temp. setting +2 ºC, unit will run
intermittently ai LOW speed regardless of FAN
setting.
2. Remote controller can memorize each operation
status. When starting it next time, just press ON/
OFF button and unit will run in previous status.

Operation
1button.
pressed, temp. setting
increases ºC.
pressed, temp. setting
decreases ºC.
Unit will start running to reach the
temp. setting on LCD.
SMART
POWER
2AN Operation
changes as follows:
Unit will run at selected fan speed.
SMART Operation
(This function is unavailable on
some models)
One key can give you a
comfortable room!
The air conditioning unit can
judge the indoor temperature and
humidity, and make the adjustment
accordingly.
SMART
SMART start
Press ON/OFF button, unit starts.
Press SMART button “ ” is
displayed on the remote controller.
SMART
POWER

Operation
HEALTH AIRFLOW Operation FAN MODE Operation
The setting of
function
FAN
MODE
Fan mode: default low fan speed,fan
mode , the setting temperature will
not display, the temperature of indoor
display is 24℃
appears on the display. Avoid
the body.
TIMER
TIMER
again, appears on the display.
direct to the body.
FAN MODE
FAN MODE
The cancel of
function
and outlet grills of the air conditioner are opened, and
the unit goes on working under the condition before the
grille will close automatically.
Notice:
Cannot pull direct the outlet grille by hand. Otherwise, the
grille will run incorrectly. If the grille is not run correctly,
stop for a minute and then start, adjusting by remote
controller.
Remote controller can memorize each operation status.
when starting it next time, just press ON/OFF button and
unit will run in previous status.
Note:
mode.
mode.
5
2. In heating, it is better to select the
3. In cooling, it is better to select the
4. In cooling and dry, using the air conditioner for a
long time under the high air humidity, a phenomenon
falling drips of water occurs at the outlet grille.
5. Select the appropriate fan direction according to the
actual conditions.

When humidity is high, condensate water might occur
at air outlet if all vertical louvers are adjusted to left or
right.
position for a long time in COOL or DRY mode,
otherwise, condensate water might occur.
better air circulation
Operation
SWING Operation TIMER Operation
Set Clock correctly before starting Timer operation. You can
let unit start or stop automatically a following times: Before
you wake up in the morning, or get back from outside or
after you fall asleep at night.
1
1
1Select your desired operation
mode.
For each press of “ ” button, air Select your desired
TIMER ON.
displays as follows according to
different operation modes: Remote controller: “
TIMER ON
”
TIMER
COOL/DRY: Select your desired
TIMER OFF.
FAN MODE HEAT: Remote controller: “
TIMER OFF
”
FAN MODE
SMART: 2Time setting.
Initial state
2Every time the button is pressed,
time setting increases or decreases
1 min, if kept depressed, it will increase rapidly. It can be
adjusted within 24 hours.
3
For each press of “
displays as follows:
remote controller:
” button, remote controller
APPLY
“
ON
” or “
OFF
”
Initial state
To cancel TIMER mode
Just press TIMER button several times until TIMER
dispiay disappear.
6

Operation
Comfortable SLEEP
3 hours then stops. Temp. is lower than temp. setting
so that room temperature won’t be too high for your
sleep.
Before going to bed, you can simply press the SLEEP
button and unit will operate in SLEEP mode and bring you
a sound sleep.
Press SLEEP
button. Temp. setting Unit stop
1 hr Decreases 2 ºC
Operation Mode
1. In COOL, DRY mode
1 hours after SLEEP mode
starts, temp. will become 1 ºC
higher than temp. setting. After
another 1 hours, temp. rises by
1 ºC further. The unit will run for
further 6 hours thenstops Temp.
is higher than temp. setting so
that room temperature won’t be
too low for your sleep.
1 hr
Decreases 2 ºC
3 hrs
3 hrs Rises 1 ºC
SLEEP
operation starts
SLEEP
operation stops
In HEAT mode
FAN MODE
4. When quiet sleeping function is set to 8 hours the
quiet sleeping time can not be adjusted. When TIMER
function is set, the quiet sleeping function can’t be
set up. After the sleeping function is set up, if user
resets TIMER function, the sleeping function will be
cancelled; the machine will be in the state of timing-
on, if the two modes are set up at the same time, either
automatically, and the other mode will be cancelled.
Power Failure Resume Function
not start running unless 3 minutes have elapsed. When
the power resumes after power failure, the unit will run
automatically, and 3 minutes later the compressor starts
running.
Note to the power failure resume:
SLEEP
operation starts
SLEEP
operation stops
Approx. 6hrs
1 hr Rises 1 ºC
1 hr Rises 1 ºC
Temp. setting Unit stop
In COOL, DRY mode
enter function after hearing four sounds. And press the
this function after hearing two sounds.
2. In HEAT mode
1 hours after SLEEP mode starts, temp will become
2 ºC lower than temp. setting. After another 1 hours,
temp decrease by 2 ºC further. After more another
3 hours, temp. rises by 1 ºC further. The unit will run for
further