INVENTOR EU-OSK105 User manual

ENGLISH | ΕΛΛΗΝΙΚΑ | ROMANA | DEUTSCH
• USER’S MANUAL
• ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ
• MANUAL UTILIZATORULUI
• BENUTZERHANDBUCH
Wi-Fi FUNCTION
AIR CONDITIONING SYSTEMS
Wi-Fi

3
CONTENTS
1 SPECIFICATION..................................................4
2 PRECAUTIONS ...................................................4
3 DOWNLOAD AND INSTALL APP......................5
4 INSTALL THE SMART KIT
(WIRELESS MODULE).........................................6
5 USER REGISTRATION ........................................7
6 NETWORK CONFIGURATION...........................8
7 HOW TO USE THE APP ....................................20
8 SPECIAL FUNCTIONS ......................................22
DECLARATION OF CONFORMITY
Hereby, we declare that this AC is in compliance
with the essential requirements and other relevant
provisions of Directive 2014/53/EU.
A copy of the full DoC is attached.

4
Model: EU-OSK105
Standard: IEEE 802. 11b/g/n Antenna Type: Printed PCB
Antenna
Frequency: 2400~2483.5 MHz
Operation Temperature: 0ºC~45ºC/32ºF~113ºF
Operation Humidity: 10%~85%
Power Input: DC 5V/300mA
Maximum Transmitted Power: <20dBm
2PRECAUTIONS
• Applicable system: iOS, Android.
(Suggested: iOS 9.0 or above, Android 6.0 or above)
- Please keep you APP up to date with the latest version.
- Due to special situation may be occurred, we explicitly
claims below: Not all of the Android and i OS system are
compatible with APP. We will not be responsible for any
issue as a result of the incompatibility.
• Wireless safety encryption
Supported Wi-Fi band: 2.4GHz
Smart kit only support WPA-PSK/WPA2-PSK encryption
and none encryption .
WPA- PSK/WPA2-PSK encryption is recommended.
• Cautions
- Due to different network situation, control process may
return time-out sometimes. If this situation occurs, the
display between board and App may not be the same,
please do not feel confused.
1SPECIFICATION

5
- Smart Phone camera needs to be 5 million pixels or
above to make sure scan QR code well.
- Due to different network situation , sometimes , request
time-out could happen, thus, it is necessary to do
network configuration again.
- The APP system is subject to update without prior
notice for product function improvement. The actual
network configuration process may be slightly different
from the manual, the actual process shall prevail.
- Please Check The Service Website For More information.
3DOWNLOAD AND INSTALL APP
CAUTION: The following QR Code is only for downloading
the APP. This is different from the QR code the SMART
KIT has on it.
Android iOS
• Android Phone users: scan Android QR code or go to
google play, search «Invmate II» app and download it.
• iOS users: scan iOS QR code or go to APP Store, search
«Invmate II» app and download it.

6
4
INSTALL THE SMART KIT
(wireless module)
1.Remove the protective cap of the smart kit (wireless
module)
2.Open the front panel and insert the smart kit (wireless
module) into the reserved interface.
3.Attach the QR code packed with Smart kit (wireless
module) to the side panel of the machine, ensure it
is convenient to be scanned by the mobile phone.
Alternatively, user can take picture of the QR Code and
save in into their own phone.
WARNING: This interface is only compatible with
SMART KIT (wireless module) provided by the
manufacturer.
Insert

7
5
USER REGISTRATION
• Please ensure your mobile device is connected to Wi-Fi
router. Also, the Wireless router has already connected
to Internet before doing user registration and network
configuration.
• You can log in with the third party accounts.
2.Enter your email address
and password, and then
click «Registration»
1.Click «Sign up»
4
VI 5
0
Fo
5
USER REGISTRATION
Please ensure your mobile device is connected to
Wireless router. Also, the Wireless router has already
connected to Internet before doing user registration and
network configuration.
It is better to log in your email box and active your
registration account by clicking link in case you forget
the password. You can log in with the third party accounts.
1Click "Create Account
Android iOS
"
cc
2Enter your email address
an d password, and then
cl ick " "Register
5

8
6
NETWORK CONFIGURATION
Cautions
• It is necessary to forget any other local / nearby
networks and make sure the Android or i OS device
is connected to the Wireless network you want to
configure.
• Make sure during the configuration to keep your
mobile data connection turned off
• Make sure the Android or i OS device Wireless function
works well and can be connected back to your original
Wireless network automatically.
Kind reminder:
User must finish all the steps in 8 minutes after powering
on AC, otherwise you need to power on it again.
■Add New Device
1. Make sure your mobile device has already been
connected to the Wireless network which you
want to use. Also, you need to forget other local /
nearby Wireless networks in case it influences your
configuration process.
2. Disconnect the power supply of AC for 5 minutes.
3. Connect the power supply of AC, and continuously
press the “ LED DISPLAY” or “DO NOT DISTURB” button
seven times in 10 seconds.
4. When the AC displays “AP”, it means that the AC
wireless has already entered into “AP” Mode.
• Some type of AC do not need the 2 step to be in AP
mode

9
6.Select the appliance you
are setting up
5.Press “ + Add Device ”
7
Network configuration by Bluetooth scan
Note: Make sure the bluetooth of your mobile device is
working.
Press “ + Add Device ” Press “Scan for nearby
devices”
12
11
Network configuration by select appliance type :
If the bluetooth network
cofiguration is failure, please
select the appliance type.
1
Manually Add New Device:

10
7.Follow the above steps to enter “AP” mode.
12
please follow the above steps to enter “AP” mode.
2

11
9a. Scan the QR code8.Choose the network
configuration method.
13
horizontal
Choose Method
9:4 1
Note:Wait5-10 seconds while your device is in
AP mode before scanning the QR code.
Manual Setup
Scan QR code on the unit
Choose the network
configuration method.
Choose the “Scan the
QR code” method.
NOTE: Steps and are applicable to Android
system only. iOS system does not need
these two steps.
3
4
3
4

12
10. Find the network
«net_ac_XXXX» and press
to connect to it. Use
password «12345678»
to connect and return to
INVmateII. Press «Next».
9b. Or choose the “Manual
Setup” method.
14
When choose the “Manual
Setup” method(Android).
Connect to the wireless
network(iOS)
Please enter password
56
Your Wifi

13
11. Please enter your Wi-Fi
password
14
When choose the “Manual
Setup” method(Android).
Connect to the wireless
network(iOS)
Please enter password
56
Your Wifi
12. Network configuration
is successful
15
Network configuration is
successful
Configuration Success,
you can see the device
in the list.
78

14
13. Configuration Success,
you can see the device on
the list.
15
Network configuration is
successful
Configuration Success,
you can see the device
in the list.
78

15
6.Select «Scan for nearby
devices»
5. Press “ + Add Device ”
Add New Device with Bluetooth Connection:
Note: Make sure the bluetooth of your mobile device is
working.
7
Network configuration by Bluetooth scan
Note: Make sure the bluetooth of your mobile device is
working.
Press “ + Add Device ” Press “Scan for nearby
devices”
12
7
Network configuration by Bluetooth scan
Note: Make sure the bluetooth of your mobile device is
working.
Press “ + Add Device ” Press “Scan for nearby
devices”
12

16
7.Wait for your unit to appear in the list. Select the
device to add it. Select your home Wi-Fi and enter the
password.
8
Your Wifi
Wait smart devices to find,
then click to add it
Select home Wi-Fi,
enter the password
34

17
9.Network configuration
is successful.
8.Allow a few moments for
the device to connect.
9
Wait connecting to the
network
56
Configuration Success,
you can modify the default
name.
9
Wait connecting to the
network
56
Configuration Success,
you can modify the default
name.

18
11. Configuration Success,
you can see the device on
the list.
10. Select the displayed
name of your device from
the recommended, or
name you device.
10
8
7You can choose an
existing name or
customize a new name.
Bluetooth network
configuration is successful,
now you can see the
device in the list.
10
8
7You can choose an
existing name or
customize a new name.
Bluetooth network
configuration is successful,
now you can see the
device in the list.

19
NOTE:
• When finishing network configuration, APP will display
«success» on the screen.
• Due to wireless nature, it is possible that the device
status still display “offline” . If this situation occurs, it is
necessary to pull down to refresh the device list on the
APP and make sure the device status appears “online”.
Alternatively, user can turn off the AC and router power
for 5 minutes and turn on it again, the device status will
appear “online” after a few minutes.

20
7
HOW TO USE THE APP
Please ensure both your mobile device and air
conditioner are connected to the Internet before using
«INVmateII» to control the air conditioner via internet.
Please follow the next steps:
2. Choose the air
conditioner.
1. Click «Sign in»
17
7HOW TO USE APP
1Click " Sign in "
SIM!
0
82
cc
2Choose the air conditioner.
Please ensure both your mobile device and air
conditioner are connected to the Internet before
using app to control the air conditioner via internet,
please follow the next steps:
17
7HOW TO USE APP
1Click " Sign in "
SIM!
0
82
cc
2Choose the air conditioner.
Please ensure both your mobile device and air
conditioner are connected to the Internet before
using app to control the air conditioner via internet,
please follow the next steps: