INVENTOR COOL User manual

MODELS:
AIR CONDITIONING SYSTEMS
PORTABLE
COOL
FCOOL-8BS
• USER’S MANUAL
• ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ
• MANUAL UTILIZATORULUI
• BEDIENUNGSANLEITUNG
• MANUEL D’EMPLOI
• MANUALE DELL’ UTENTE
• MANUAL DEL PROPIETARIO

Content
Operation Notices
Operation environment...........................................................................................1
Safety warning........................................................................................................2
Part' s N ame............................................................................................................3
Operation Guide
Operation introduction for control panel .................................................................4
Buttons on remote controller ..................................................................................6
Introduction for icons on display screen.................................................................6
Introduction for buttons on remote controller..........................................................7
Function introduction for combination buttons........................................................9
Operation guide......................................................................................................9
Replacement of batteries in remote controller.......................................................10
Maintenance
Clean and Maintenance........................................................................................11
Malfunction
Malfunction analysis .............................................................................................13
Installation Notice
Installation Precaution..........................................................................................16
Preparation before installation..............................................................................17
Installation
Install drainage pipe .............................................................................................18
Installation and disassembly of heat discharge pipe............................................19
Operation test.......................................................................................................22
Attached sheet
D rainage way
Electric schematic diagram...................................................................................23
........................................................................................................22
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from un-
controlled waste disposal, recycle it responsibly to promote the sustainable reuse of mate-
rial resources. To return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this product for envi-
ronmental safe recycling.
R410A(R32/125: 50/50): 2087.5

1
Operation environment
●This air conditioner can only be used for family, not for
commercial purposes.
● The appliance is for indoor use only.
● The operating range of the Cool portable Air conditioner
is 16oC- 35oC.
● The appliance must be positioned so that the plug is accessible.
● Reserved space around the air conditioner should be 12″(30cm)
at least.
● Do not operate the air conditioner at humid environment.
● During operation, close doors and windows to improve cooling effect.
● Please keep air inlet and air outlet clean, no obstacles.
to avoid noise and vibration.
● Please put the air conditioner at smooth and flat ground for operation
● This air conditioner is equipped with castors. Castors should slide
at smooth and flat ground.
● Please refrain from titling or turning over the A/c unit. If there’s
abnormity, please disconnect power immediately and contact dealer.
● Avoid using the a/c unit under direct sunshine.
30cm
30cm
30cm

2
Safety warning
sure the unit is firstly turned off and disconnected from the mains.
e sure the gounding is reliable.
● If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person
● Please refrain from accessing the power cord with wet hands.
disconnect power at once and then contact local dealer.
● If abnormal condition occurs (e.g. burned smell), please
● Do not leave the unit operating unattended, in such event please
turn it off and unplug from the mains
● Before operating the a/c unit check that the power source is
compliant with the specifications of the unit shown
● Please ensure that the power cord is not damaged/ soiled
by heavy or hard objects
cause short circuit or damage to air conditioner.
● If use drainage hose, nearby temperature can’t lower than 0℃.
air conditioner.
● Do not repair or disassemble the air conditioner by yourself.
on the air conditioner.
● Keep the a/c unit away from fire, explosive materials
and flammable objects.
● Prohibit operating heating equipment
● Do not operate any heating equipment around the a/c.
around the air conditioner.
● Do not pull or drag the power cord to pull out the power plug or
move the air conditioner.
●
above and persons with reduced physical,sensory or mental
ve
been given supervision or instruction concerning use of the
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
please make

3
P art' s Nam e
H eat-removal pipe and other installation accessories can' t be discarded.
Note:
1
2
3
4
5
1213 11 10
9
6
7
8
Remote controller
Jo int A
H eat removal pipe
Jo int B
Jo int C
1Controller panel
2G uide louver
3Swing louver
4heel
5Remote controller bo
6Power cord
7Filters
8Upper air inlet grille
9Lower air inlet grille
10
11
12
13

4
The operation of the control Panel
Understanding the Control Panel functions
ON/OFF buttonMODE button + / - button
fan mode indicator
dry mode indicatorcool mode indicatorsignal receiving window
water full indicator
Operation of the control panel
Note:
●On the first and initial power supply of the unit, the a/c will make a sound. This
will also allow usage of the unit from the control panel
●Under ON status, after each pressing of the button on control panel, the air
conditioner will give out a sound. Meanwhile, corresponding indicator on control
panel will be bright.
● lay.
splay set temperature
under cooling mode, while it won’t display under other modes.
By Pressing the On/Off button you can turn on or off the A/c unit
Under cooling mode, press “+” or “-” button to increase or decrease set temperature
er auto, drying
or fan mode, this button will not respond.
ON/OFF button
+ / - button
1
2

5
By pressing the MODE button the functions will rotate as follows:
R FAN
When the led display is blinking that means that the water tank is full and the
tank should be drained.
COOL: ie tube displays
set temperature. Temperature setting range is 16
°C ~30 °C .
DRY: tube won’t be
display.
FAN: Under this mode, the air conditioner only blow fan. Fan indicator is bright.
y.
water full indicator
3
4
Operation introduction for control panel
Note:
lliwrezzubehtdnanoitarepopotslliwtinueht,llufsisissahcniretawehtnehW
ter full indicator is

6
B uttons on rem ote controller
Introduction for icons on display screen
21
3
4 5
6 7
1
3
5
2
4
6
7
ON /OFF button
MOD E button
+ /- button
FAN button
I button
SLEEP button
TIMER button
Timer on Timer off Sending signal
swing operation
sleep operation
lock
set speed
Set timeSet temperature
heat operation
fan operation
dry operation
cool operation
auto operation

7
Introduction for buttons on remote controller
Note:
● When the unit is on stand-by condition and powered it can also be operated
by the Remote Controller.
● oller, the sending
signal icon " " on the display of remote controller will blink once. If the air con-
ditioner gives out a beep sound, it means the signal has been sent.
light of indoor unit display is turned on, the corresponding
nction.
Press this button to turn unit on/off.
ON/OFF button
1
By pressing the MODE button the functions can be selected as follows and the
corresponding icon " " will be lit up as each function is accessed.
●
cally according to
AT mode by remote
.)
AUTO COOL FAN HEAT
MODE button
2
●
will change quickly.
Release the button after your required set temperature is reached.
●
+ / - button
3

8
Introduction for buttons on remote controller
By pressing this button that will turn up and down the air swing
* Be noted that this may not apply on all units
SWING button (not applicable for this model)
5
Under Cool, Heat and Dry mode, press this button to turn on Sleep function. Press
this button to cancel Sleep function. Under Fan and Auto mode, this function is
unavailable.
SLEEP button
6
Timer Off. T-OFF and H icon will be
blinking. Within 5s, press + or - button to adjust the time for Timer Off. Pressing
+ or - button once will increase or decrease the time by 0.5h. Hold + or -
button for 2s, time will change quickly. Release the button after your required
will stop blinking.
ff, press this button to set Timer On. T-ON and H icon will be
blinking. Within 5s, press + or - button to adjust the time for Timer On. Pressing
+ or - button once will increase or decrease the time by 0.5h. Hold + or -
button for 2s, time will change quickly. Release the button after your required
will stop blinking.
● Cancel Timer On/Off: If Timer function is set up, press TIMER button once to
review the remaining time. Within 5s, press TIMER button again to cancel this
function.
TIMER button
7
Note:
Auto speed, air conditioner will select proper fan speed automatically acc-
ording to ambient temperature.
FAN button
4
Pressing this button can select fan speed circularly as: AUTO, SPEED 1 ( ),
SPEED 2 ( ), SPEED 3 ( ), SPEED 4 ( ) (unavailable in this air conditioner.
Speed 4 is the same with speed 3.).
AUTO
SPEED 1 (equals to low fan speed)
SPEED 3 (equals to high fan speed) SPEED 4
SPEED 2 (equals to medium fan speed)

9
Introduction for b uttons on rem ote controller
Note:
● Range of time setting is: 0.5~2h
● The interval between two motions cant eceed 5s, otherwise the remote con
troller will eit setting status.
F unction introduction for com b ination b uttons
Press  and  buttons simultaneously can turn on or turn off child lock function.
hen child lock function is started up, C indicator on remote controller is .
If you operate the remote controller, remote controller won’t send signal.
Child lock function
T em perature display sw itchov er function
nder  status, press  button and Dbutton simultaneously can switch
between °C and °.
Operation g uide
1. After putting through the power, press  button on remote controller to
turn on the air conditioner.
2. Press D button to select your required mode: AUT, C, DRY, A,
AT.
3. Press  or  button to set your required temperature. (Temperature can’t be
adusted under auto mode).
4. Press A button to set your required fan speed: auto, low, medium and high
speed.

10
Replacement ofbatteries in remote controller
Note:
● During operation, point the remote control signal sender at the receiving
window on indoor unit.
● The distance between signal sender and receiving window should be no more
than 8m, and there should be no obstacles between them.
orescent lamp
indoor unit during
operation.
● Replace new batteries of the same model when replacement is required.
take out the the remote control
batteries.
replace with new batteries of the same type.
reinstall
remove
battery
1. Press the back side of remote controller on the
spot marked with " ", and then push out the
make sure the positions of + and- polar are
correct.

11
Clean and Maintenance
Warning:
power. Otherwise, it may cause electric shock.
shock.
●Do not use volatile liquid (such as thinner or gas) to clean the air conditioner.
Otherwise, it may damage the appearance of air conditioner.
Clean outer case:
If there's dust on the surface of outer case, please use soft towel
to wipe it. If the outer case is very dirty (such as grease), please
use neutral abluent to wipe it.
Clean outer case and grille
Clean grille: Use cleaner or soft brush to clean it.
Note:
① ②
1
3
2In order to clean the internal filter
please use lukewarm water. In
the even the filter is very dirty
(such as grease), use warm
water 40c /104F with neutral
cleaning detergent. Let filter in a
shaded area to dry in the air.
dried, reinstall it well.
●It is recommended that the filter is cleaned at least once every month. If the
surrounding environment has increased level of dust/dirt it is advisable to have it
cleaned more often.
●Do not use assisted methods to dry the air filter such as fire, or a hair drier as
this make cause damage to the filter element.

12
Clean and Maintenance
Clean heat-removal pipe
Remove the heat-removal pipe from air conditioner, clean and dry it , and then
d, please refer to the
instruction for "Installation and disassembly of heat discharge pipe").
Checking before use-season
1. Check whether air inlets and air outlets are blocked.
2. Check whether plug and socket are in good condition.
4. Check whether batteries is installed in remote controller.
e installed tightly.
6. Check whether heat-removal pipe is damaged.
Checking after use-season
1. Disconnect power supply.
3. Remove dust and sundries on the air conditioner.
4.
Eliminate accumulated water in chassis (refer to the section of "Drainage way"
for details).
5. Check whether window bracket is damaged or not. If yes, please contact dealer.
Long-time storage
If you don't use the air conditioner for a long time, please maintain it by following
steps for good performance:
disassembled.
● Pull out the plug and wrap the power cord.
● Clean the air conditioner and pack it well to prevent dust.
Packaging and Materials
● In the event the a/c unit is faulty or damaged, please do ensure that
recycled at an electrical appliances facility that can handle refrigerant materials
and cooling liquids.
● The Packaging material are made out of recycled materials. Please dispose
them carefully at the designated recycling facilities available in our area.

13
Malfunction analysis
Please check below items before asking for maintenance. If the malfunction still
ofessionals.
Phenomenon Troubleshooting Solution
Air conditioner
can't operate
A/C unit does
not accept
signal form
the remote
control unit or
does not
respond to
remote control
commands.
Poor cooling
(heating)
ert the plug after about 3min,
and then turn on the unit.
●
The receiving range of remote
ed this range.
● Remove the obstacles.
● Check the batteries of remote
controller. If the power is low,
please replace the batteries.
close to air conditioner.
●
and try it again.
●
● Close door and window.
● Reinsert the plug.
●Ask professional person to●Is the air switch tripped or the
unit fuse is burnt?
●Has the unit been started and
stopped instantly?
●Is the air filter too dirty?
●Does the temperature
generated feels inadequate?
●Are the doors and windows
closed?
●Has the unit been interfered
(such as with static pressure
or unstable voltage?)
●The remote control is not
within operating range
● The remote control is blocked
by obstacles and does not
communicate
●Thereis a Fluorescence lamp
situated in the room with the
a/c unit
replace air switch or fuse.
●Ask professional person to
replace circuit.
on the unit again.

14
Phenomenon Troubleshooting Solution
Set tempera-
ture can't be
ted under auto mode.
Malfunction analysis
●Indoor unit will stop blowing●When using heating mode the
indoor temperature has reached
the desired/set temperature.
●Check if the Air outlet or air
inlet is blocked
● The evaporator looks like the
a/c unit is defrosting (This can
be identified by looking the
internal filter)
● The unit operates in auto
mode
● Is the required temperature
excessive of the set
temperature?
● Heating mode has just been
initiated.
fan after reachingto set
temperature.
● As to prevent cold air from
been blown the unit will delay
the function as such. This is
normal operation
●This is normal operation of the
a/c unit. It will automatically enter
the defrosting mode and will
resume once finished.
Air does not
flow out of
the a/c unit
There's off the room, such as furniture,
cigarette etc.
source.
There's abnor-
mal sound du-
ring operation
ugh the power again, and
then turn on the unit again.
sound
rigerant inside the air condit-
ioner, which is the normal
phenomenon.
● Is the unit interfered by
thunder, radio etc?
● The unit has been turned off
and on just now
● The unit has been turned off
and on just now?
● Heat expansion or shrinkage
of the internal cooling
mechanism may cause
additional sounds
You can hear
sounds on the
internal piping

15
Malfunction analysis
Malfunction code
Overcurrent protection.
Chassis is full of water.
Malfunction of ambient
temperature sensor.
Please contact previsional person to deal
with it.
Malfunction of evaporator
temperature sensor.
Please contact previsional person to deal
with it.
1. Pour out the water inside chassis.
2. If "H8" still exits, please contact professional
person to maintain the unit.
Disconnect power, and then turn on
the unit
again after 10min. If "E5" still
exits, please
contact professional person to maintain the unit.
Warning
●The operation of the a/c unit under abnormal or unfit usage, may cause the
a/c unit to malfunction, electrical shock, fire or hazard.
●In the unlike event the following are observed, please turn of the a/c unit
and disconnect the power form the mains immediatelly, also contact the
authorised dealer aged.
Abnormal sound during operation.
Water leakage
F0
F2
F1
H8
E5
H3
E8
F4
1.Refrigerant is leaking
2.System is blocked
1. Re-energize the unit after turning off and
pulling out the plug for 30min;
after-sales service.
Overload protection for compressor
Overload malfunction
1.Check if the unit is under high-temperature
and high-humidity environment; if ambient
temperature is too high, power off the unit and
then energize it for operation after the ambient
temperature drops to 35℃below.
2. Check if the evaporator and condenser are
blocked by some objects; if yes, take away the
objects, power off the unit and then energize
it for operation.
3. If the malfunction still occur, please contact
our after-sales service center.
Outdoor tube temperature
sensor is open/short-circuited.
Please contact after-sale service person
to deal with it.

16
Installation P recaution
W arning :
● bserve all governing codes and ordinances.
● Do not use damaged or nonstandard power cord.
● e caution during installation and maintenance. Prohibit incorrect operation
to prevent electric shock, casualty and other accidents.
S election of Installation L ocation
R eq uirem ents F orelectric Connection
B asic req uirem ent
Installing the unit in the following places may cause malfunction. If it is unavoidable, please
consult the local dealer:
obects spread in the air.
2. The place with highfrequency devices (such as welding machine, medical equipment).
3. The place near coast area.
. The place with oil or fumes in the air.
5. The place with sulfureted gas.
6. ther places with special circumstances.
R eq uirem ent of air conditioner
1. Air inlet should be far away from obstacles and do not put any obects near air outlet.
therwise, it will affect the radiation of heatremoval pipe.
2. elect a location where the noise and outflow air emitted by the outddor unit will not affect
neighborood.
3. Please try your best to keep far away from fluorescent lamp.
.The appliance shall not be installed in the laundry.
S afety precaution
1. ust follow the electric safety regulations when installing the unit.
2. According to the local safety regulations, use qualified power supply circuit.
3. or appliances with type  attachment,the instructions shall contain the substance of
the following.If the supply cord is damaged,it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a haard.
. Properly connect the live wire, neutral wire and grounding wire of power socket.
5. e sure to cut off the power supply before proceeding any work related to electricity and
safety.
6. Do not put through the power before finishing installation.
. The air conditioner is first class electric appliance. It must be properly grounding with
specialied grounding device by a professional. Please make sure it is always grounded
effectively, otherwise it may cause electric shock.
. The yellowgreen wire or green wire in air conditioner is grounding wire, which cant be
used for other purposes.
. The grounding resistance should comply with national electric safety regulations.
10. The appliance shall be installed in accordance with national wiring regulations.

17
P reparation b efore installation
Note: check if the accessories are available before installation.
Accessory list
unit j oint A j oint Bj oint C
heat discharge pipe
drainage pipe remote controller user' s manual
battery (2)
(AAA 1.5V)
screw(1) pipe clip rubber plug pipe hoop (2)
T ools needed for installation
cross screwdriver
gauge
straight screwdriver
scissors
saw
pencil