INVENTOR EU-OSK105 User manual

ENGLISH | ΕΛΛΗΝΙΚΑ | ROMANA |
DEUTSCH | FRANÇAIS | ITALIANO | ESPAÑOL
• USER’S MANUAL
• ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ
• MANUAL UTILIZATORULUI
• BENUTZERHANDBUCH
• MANUEL D’UTILISATION
• MANUALE DELL’ UTENTE
• MANUAL DE USUARIO
Wi-Fi FUNCTION
DEHUMIDIFIERS
Wi-Fi

3
CONTENTS
1 SPECIFICATION..................................................4
2 PRECAUTIONS ...................................................4
3 DOWNLOAD AND INSTALL APP......................5
4 USER REGISTRATION ........................................6
5 NETWORK CONFIGURATION...........................7
6 HOW TO USE THE APP ....................................19
7 SPECIAL FUNCTIONS ......................................21
DECLARATION OF CONFORMITY
Hereby, we declare that this unit is in compliance
with the essential requirements and other relevant
provisions of Directive 2014/53/EU.
A copy of the full DoC is attached.

4
Model: EU-OSK105
Standard: IEEE 802. 11b/g/n Antenna Type: Printed PCB
Antenna
Frequency: 2400~2483.5 MHz
Operation Temperature: 0ºC~45ºC/32ºF~113ºF
Operation Humidity: 10%~85%
Power Input: DC 5V/300mA
Maximum Transmitted Power: <20dBm
2PRECAUTIONS
• Applicable system: iOS, Android.
(Suggested: iOS 9.0 or above, Android 6.0 or above)
- Please keep you APP up to date with the latest version.
- Due to special situation may be occurred, we explicitly
claims below: Not all of the Android and i OS system are
compatible with APP. We will not be responsible for any
issue as a result of the incompatibility.
• Wireless safety encryption
Supported Wi-Fi band: 2.4GHz
Smart kit only support WPA-PSK/WPA2-PSK encryption
and none encryption .
WPA- PSK/WPA2-PSK encryption is recommended.
• Cautions
- Due to different network situation, control process may
return time-out sometimes. If this situation occurs, the
display between board and App may not be the same,
please do not feel confused.
1SPECIFICATION

5
- Smart Phone camera needs to be 5 million pixels or
above to make sure scan QR code well.
- Due to different network situation , sometimes , request
time-out could happen, thus, it is necessary to do
network configuration again.
- The APP system is subject to update without prior
notice for product function improvement. The actual
network configuration process may be slightly different
from the manual, the actual process shall prevail.
- Please Check The Service Website For More information.
3DOWNLOAD AND INSTALL APP
CAUTION: The following QR Code is only for downloading
the APP. This is different from the QR code the SMART
KIT has on it.
Android iOS
• Android Phone users: scan Android QR code or go to
google play, search «Invmate II» app and download it.
• iOS users: scan iOS QR code or go to APP Store, search
«Invmate II» app and download it.

6
4
USER REGISTRATION
• Please ensure your mobile device is connected to Wi-Fi
router. Also, the Wireless router has already connected
to Internet before doing user registration and network
configuration.
• You can log in with the third party accounts.
2.Enter your email address
and password, and then
click «Registration»
1.Click «Sign up»
4
VI 5
0
Fo
5
USER REGISTRATION
Please ensure your mobile device is connected to
Wireless router. Also, the Wireless router has already
connected to Internet before doing user registration and
network configuration.
It is better to log in your email box and active your
registration account by clicking link in case you forget
the password. You can log in with the third party accounts.
1Click "Create Account
Android iOS
"
cc
2Enter your email address
an d password, and then
cl ick " "Register
5

7
5
NETWORK CONFIGURATION
Cautions
• It is necessary to forget any other local / nearby
networks and make sure the Android or i OS device
is connected to the Wireless network you want to
configure.
• Make sure during the configuration to keep your
mobile data connection turned off
• Make sure the Android or i OS device Wireless function
works well and can be connected back to your original
Wireless network automatically.
Kind reminder:
User must finish all the steps in 8 minutes after powering
on AC, otherwise you need to power on it again.
■Add New Device
1. Make sure your mobile device has already been
connected to the Wireless network which you
want to use. Also, you need to forget other local /
nearby Wireless networks in case it influences your
configuration process.
2. Disconnect the power supply of the dehumidifier for
5 minutes.
3. Connect the power supply of the dehumidifier and
press and hold the «FILTER» button for more than 3
seconds (the required button might be different, kindly
advise the User Manual of your unit).
4. When the dehumidifier displays “AP”, it means that
the dehumidifier wireless has already entered into “AP”
Mode.

8
6.Select the appliance you
are setting up
5.Press “ + Add Device ”
7
Network configuration by Bluetooth scan
Note: Make sure the bluetooth of your mobile device is
working.
Press “ + Add Device ” Press “Scan for nearby
devices”
12
2
5
Choose the network
configuration method.
3
Choose the “ Scan the
QR code ” method. Sacn
the QR code on the unit.
4
NOTE: Steps 3 and 4 are applicable to Android system only. iOS system does not need
these two steps.
Please follow the above steps to enter “AP” mode.
Choose Method
Back
Scan QR code on the unit
Manual Setup
Note:Wait5-10 seconds while your device is in
AP mode before scanning the QR code.
Network configuration by select appliance type :
If the bluetooth network
cofiguration is failure, please
select the appliance type.
1
When choose the “Manual
Setup” method(Android).
Connect to the wireless
network(iOS)
5
Manually Add New Device:

9
7.Follow the above steps to enter “AP” mode.
12
please follow the above steps to enter “AP” mode.
2
2
5
Choose the network
configuration method.
3
Choose the “ Scan the
QR code ” method. Sacn
the QR code on the unit.
4
NOTE: Steps 3 and 4 are applicable to Android system only. iOS system does not need
these two steps.
Please follow the above steps to enter “AP” mode.
Choose Method
Back
Scan QR code on the unit
Manual Setup
Note:Wait5-10 seconds while your device is in
AP mode before scanning the QR code.
Network configuration by select appliance type :
If the bluetooth network
cofiguration is failure, please
select the appliance type.
1
When choose the “Manual
Setup” method(Android).
Connect to the wireless
network(iOS)
5

10
9a. Scan the QR code8.Choose the network
configuration method.
13
horizontal
Choose Method
9:4 1
Note:Wait5-10 seconds while your device is in
AP mode before scanning the QR code.
Manual Setup
Scan QR code on the unit
Choose the network
configuration method.
Choose the “Scan the
QR code” method.
NOTE: Steps and are applicable to Android
system only. iOS system does not need
these two steps.
3
4
3
4