IOGear GME228BW6 User manual

1
GME228BW6
PART NO. M0411
Installation
Installation
Installation Guide
Bluetooth®Laser Mouse
Souris laser Bluetooth®
Guide
Guide
Guide d’installation
Ratón láser Bluetooth®
Guia de
Guia de
Guia de Instalacion

2

3
Package Contents
This package contains:
1 Bluetooth®Laser Mouse
1 Carrying case
1 USB battery charger cable
1 User manual
2 AAA rechargeable batteries
1 Warranty/Registration card
If any of the items are missing or damaged, please contact your dealer immediately.

4
Requirements
Computer/Laptop must be Bluetooth-enabled and support the HID profile•
Operating System:•
Windows 98SE/ME/2000/XP•
Windows Vista•
MAC OS X v10.3.5 or later•
If the computer/laptop is currently not Bluetooth-enabled, a Bluetooth®USB adapter will be
required. Refer to IOGEAR part number GBU221 and GBU321

5
Pictorial Introduction
Scroll Wheel1.
Right Click Button2.
Left Click Button3.
Battery Charging Connection4.
Battery Cover Release5.
Battery Compartment6.
Connect Button7.
Laser Sensor8.
Power On/Off Switch9.
9
7
8
51
2
3
4
6

6
Before You Start
BATTERY INSTALLATION
Push the battery cover release1.
Insert the batteries (included in the package)2.
into the battery compartment
Put the cover back on3.
Make sure the power On/Off switch is at ON4.
position. We do recommend that you charge
the batteries for 10 hours before using the
mouse
To charge the batteries, just plug the USB5.
charger cable into the USB port on you
computer, and the mouse, and leave it on
1
2

7
INSTALLATION INSTRUCTIONS
Before you can use the IOGEAR Bluetooth®mouse with your computer, you will first need to establish
communication and then connect to it. The procedures below may be different for you, depending on the
Bluetooth software you are using. If you need additional help, please consult the manual for your Bluetooth
software.
Keep in mind that for the initial configuration, the Bluetooth®mouse will not be functional and that you will
need to use a different mouse.

8
Installation (Windows XP-Widcomm BTW 5.1.0.2700)
In the example below, the Bluetooth software
used was WIDCOMM BTW 5.1.0.2700
Make sure your computer is Bluetooth-1.
enabled and that it supports the Bluetooth
HID profile.
Turn ON the mouse.2.
Open your Bluetooth software (My3.
Bluetooth Places, in our example)
Press and hold the Connect button located4.
under the mouse for approximately five (5)
seconds; this will set the mouse in discovery
mode.
Start the search for Bluetooth devices5.
(Search for devices in range)
The IOGEAR Bluetooth6. ®mouse should be
listed as shown in the image. If the mouse is
not detected, repeat step 4 and search for
your Bluetooth®mouse again.

9
Right-click the IOGEAR Bluetooth7. ®mouse
and select “Connect Device.”
When prompted to connect, click Yes.8.
Then simply click the Click here button with9.
the Bluetooth®mouse to confirm that the
mouse is paired with your computer.

10
You should now be able to use the IOGEAR10.
Bluetooth®mouse. Once you have
connected and paired your mouse with your
Bluetooth-enabled computer, you don’t need
to repeat this procedure. Even if you turn on/
off the Bluetooth®mouse or shut down your
computer, the mouse will still connect to the
computer when both devices are turned on.

11
Disconnect Device (Windows XP-Widcomm BTW 5.1.0.2700)
If you would like to disconnect your Bluetooth®
mouse, just open My Bluetooth places. Right
click on the Bluetooth®mouse in Entire
Bluetooth Neighborhood and simply click on
disable. When prompted to disable, click Yes.

12
Installation (Windows XP SP2-Microsoft Bluetooth stack)
The instructions below apply to Windows XP
systems with Service Pack 2 installed.
Make sure that your computer is Bluetooth-1.
enabled and that the Bluetooth icon shows
on your tray-bar.
Right-click on the Bluetooth icon and select2.
“Add a Bluetooth Device.”

13
Before proceeding with the Bluetooth3.
Wizard, please do the following:
Your computer will scan for Bluetooth4.
devices in your area and display all found
devices. On this window, you should see
“Bluetooth Mouse” as shown below. Select
the mouse and click Next to continue.
Switch ON the Bluetooth®mouse
Press and hold the “connect” button
underneath the mouse for five (5)
seconds and then release
Click the checkbox “My device is setup
and ready to be found” and then click
Next
•
•
•

14
At this point, the IOGEAR Bluetooth6. ®mouse
should be functional. Simply click Finish to
close the Wizard.
To pair with the Bluetooth5. ®mouse, select
“Don’t use a passkey”. Upon clicking Next,
Windows XP will pair with the mouse and
install the necessary drivers for your mouse.

15
Disconnect Device (Windows XP SP2-Microsoft Bluetooth stack)
If you would like to disconnect your Bluetooth®mouse, just open the Bluetooth devices control panel and
delete the pairing for the mouse.

16
Installation (Windows Vista x86/x64-Microsoft Bluetooth Stack)
The instructions below apply to Windows Vista
x86/x64 systems.
Make sure that your computer is Bluetooth-1.
enabled and that the Bluetooth icon shows
on your tray-bar.
Right-click on the Bluetooth icon and select2.
“Add a Bluetooth Device.”

17
Before proceeding with the Bluetooth3.
Wizard, please do the following:
Switch ON the Bluetooth®mouse.
Press and hold the “connect” button
underneath the mouse for five (5)
seconds and then release.
Click the checkbox “My device is setup
and ready to be found” and then click
Next.
•
•
•
Your computer will scan for Bluetooth4.
devices in your area and display all found
devices. On this window, you should see
“Bluetooth Mouse” as shown below. Select
the mouse and click Next to continue.

18
To pair with the Bluetooth5. ®mouse, select
“Don’t use a passkey”. Upon clicking Next,
Windows XP will pair with the mouse and
install the necessary drivers for your mouse.
At this point, the IOGEAR Bluetooth6. ®mouse
should be functional. Simply click Finish to
close the Wizard.

19
Disconnect Device (Windows Vista x86/x64-Microsoft BluetoothStack)
If you would like to disconnect your Bluetooth®mouse, just open the Bluetooth devices control panel and
delete the pairing for the mouse.

20
Installation (Mac OS)
Bluetooth support is built-in in MAC OS X. In the
example below, we used MAC OS X v10.3.5 to
configure the IOGEAR Bluetooth®Mouse.
Make sure your computer is Bluetooth-1.
enabled and that it supports the Bluetooth
HID profile.
Turn ON the mouse.2.
Open System Preferences and double-click3.
on the Bluetooth icon.
Under the settings tab, make sure that4.
Bluetooth is ON and that the box next to
Discoverable is checked.