IOGear GWU647 User manual

Installation
Installation Guide
Universal 5-Port Wi-Fi N Ethernet Hub
GWU647
PART NO. M1200

3
Table of Contents
Package Contents 4
System Requirements 5
Product Overview 6
Installation 8
Installation without WPS - Windows XP 10
Installation without WPS - Windows Vista 16
Installation without WPS - Windows 7 24
Installation without WPS - Mac 32
Manual Set Up 37
Firmware Upgrade 41
Federal Communications Commission (FCC)
Statement 46
CE Compliance 47
SJ/T 11364-2006 48
Limited Warranty 49
Contact 50

4
Package Contents
• 1 X Universal 5-Port Wi-Fi N Ethernet Hub
• 1 X AC to USB Power Cable
• 1 X AC to USB Power Adapter
• 1 X Ethernet Cable
• 1 X Quick Start Guide
• 1 x Warranty Card

5
System Requirements
• Operating System
- Windows XP, Windows Vista, Windows 7
- Mac OS X v10.4 and above
• Wireless network with WPS setup
• Wireless network without WPS setup and computer

WPS
Reset PWR51 2 3 4
6
Product Overview
2 31
4
1. WPS Button
Push and hold the WPS button for
5~10 seconds to enable the WPS
feature.
2. Ethernet Port
The Ethernet port allows a LAN
connection through Cat 5 cables.
Supports auto-sensing at 10/100M
speed, half/ full duplex.
3. AC Power
AC Power Adapter
4. Reset Button
Push and hold the reset button for
5~10 seconds to reset the Wi-Fi
Hub to factory default setting

7
LED Indicator State Description
12 3 4
1. LAN LED
Flashing - Data is transmitting or
receiving on the LAN interface.
On - Port linked.
Off – No link.
2. WPS LED
Flashing - The WPS feature is enabled
and in use.
Off - The WPS feature is not in use.
3. WLAN LED
Flashing - WLAN is transmitting or
receiving data.
Off - WLAN is off
4. Power LED
On - Power on.
Off - Power off.

8
Installation
Wireless Setup with WPS
Step 1: Power on your Universal WiFi Hub using
either of these methods:
•ConnecttheACAdaptercabletoadevice.Make
sure that the device where you connect the AC
Adapter cable is powered on.
•ConnecttheWiFiHubtoanelectricaloutletwith
the included power adapter.
Note: It will take about 50 seconds to complete the
boot-up sequence. When complete, PWR (power)
LED will be active, and the WLAN Activity LED will
be blinking to show the WLAN interface is enabled.
Step 2: Use the included RJ-45 Ethernet cable to
connect the WiFi Hub with your device such as
Blu-ray player, HDTV, or game console.
Step 3: Refer to your wireless router’s user manual
to enable the WPS function, then press “WPS”
button on the back of WiFi Hub.
Your installation is complete. If asked for the type
of connection, make sure “WIRED” is selected on
your device.

WPS
Reset PWR51 2 3 4
9
Step 1
Step 3
Step 2

10
Installation without WPS - Windows XP
Step 1: Turn off your computer’s wireless
connection (if applicable) and disconnect the
Ethernet cable currently connect to your computer
(if applicable).
Step 2: Use the included RJ-45 Ethernet cable to
connect the WiFi Hub with your computer.
Step 3: Set your computer with a static IP address.
a. Right click on “My Network Places” and select
“Properties”.

11
b. Next, right click on “Local Area Connection”
and select “Properties”.

12
c. Select “Internet Protocol (TCP/IP)” then
select “Properties”.
D. Select “Use the following IP address” and
enter 192.168.1.3 in the IP address section.
Next enter 255.255.255.0 in the Subnet Mask.
Click OK.

13
Step 4: Open your web browser and enter
192.168.1.252.Thiswillbringuptheconguration
utility. Click “Site Survey” to scan for your wireless
network.

14
Step 5: Select the AP you want to connect to and enter the password if the network is secured. Click
the “Connect” button to establish the connection.
If your network security settings are set to not broadcast your SSID, then you will need to manually set
up the SSID and the wireless security (WEP or WPA). (Please see Page. 37)

15
Step 6: Close your browser and change the
network settings on your computer back to DHCP
(Obtain an IP address Automatically & Obtain DNS
server address automatically). Refer to steps 3a
through 3d. Also do not forget to enable your
wireless connection if you disabled it.
Step 7: Disconnect the Ethernet cable from your
computer.
Step 8: Use the included RJ-45 Ethernet cable to
connect the WiFi Hub with your device such as a
Blu-Ray player, HDTV, or game colsole.
Step 9: Power on your Hub using the AC adapter.
The installation is complete. Your device is now
wireless. If the device asks for the type of internet
connection, make sure “WIRED” is selected.

16
Installation without WPS - Windows Vista
Step 1: Turn off your computer’s wireless connection (if applicable) and disconnect the Ethernet cable cur-
rently connect to your computer (if applicable).
Step 2: Use the included RJ-45 Ethernet cable to connect the WiFi Hub with your computer.
Step 3: Set your computer with a static IP address.
a. Click the start button, the click on Control Panel.

17
b. Under Network and Internet, click “View network status and tasks”.

18
c. Under Tasks in the left pane, click “Manage
network connections”.
d. Next, right click on “Local Area Connection”
and click “Properties”.

19
e. Next, select “Internet Protocol Version 4
(TCP/IPv4)” and click “Properties”

20
f. Select “Use the following IP address” and
enter 192.168.1.3 in the IP address section.
Next enter 255.255.255.0 in the Subnet Mask.
Click OK.