IOLINK SA-COM Series User manual

SA-COM Series Push-typed Screwless Terminal Block for Power Common
User’s Guide
Thank you for purchasing product of SAMWON ACT.
Please check model of product that you purchase first, and read this manual prior to use it.
●Caution for Safety
Caution
Case that results in serious damage in human body or equipment, and fire if user handles this equipment wrongly
Warning
Case that results in slight damage in human body or equipment, and fire if user handles this equipment wrongly
Caution
1. When machining and wiring the mounting hole, do not allow foreign matter such as dust or wire covering
to enter the connection terminal. Failure to do so may result in damage to the unit, heat, or ignition.
2. Be sure to shut off the power supply from the outside before mounting and wiring.
Warning
1. Use within the specified temperature range. (-10℃~ +50℃) Damage to the outer case may occur.
2. Use within the specified rated voltage and rated current range.
This may result in fire or damage to the product.
3. Read this user's guide which is attached to product, and check product's nominal, characteristics,
specification, wiring diagram and how to handle prior to use.
4. Please make sure to check the arrangement of the +,- when wiring.
It may be the cause of malfunction or damage of this equipment and user's.
※The connection cable for PLC of various makers is provided by us. Please refer to the
catalogue or contact Head or branch office if you need more detail models and specifications.
●Model Selection
●Characteristics ●Material
※Be sure to use a ferrule or round type terminal when using a stranded wire.
●Model Configuration
❶Common dedicated Push Type 5.0mm pitch
European screwless terminal block
❷No. of terminal Poles
❸Common terminal configuration
SA-COM 20 
❶❷❸
Model No. of
Poles Common terminal configuration Dimensions (W *D mm)
Mounting
method
SA-COM20 20 Upper row 10P(+)/ Lower row 10P(-) Common 57.5 ✽48.0
Screw
mounting/
DIN Rail
SA-COM20B Left side row 10P(+)/ Right side row 10P(-) Common
SA-COM20D 40(20x2) Upper terminal block 20P(+) / Lower terminal block 20P(-) Common 63.0 ✽56.2 DIN Rail
SA-COM40 40 Upper row 20P(+)/ Lower row 20P(-) Common 107.5 ✽48.0
Screw
mounting/
DIN Rail
SA-COM40B Left side row 20P(+)/ Right side row 20P(-) Common
Rated voltage 125V AC / 24V DC
Rated current 10A (Total)
Insulation resistance 100㏁or above (DC 500V)
Dielectric strength AC500V 1min
Applicable
wire
Single wire 0.5~1.5㎟
Twisted wire UL : 17~22AWG / IEC 1.0㎟
Wire stripping length 8~9mm
Ambient temperature -10℃~+50℃(No condensation)
Terminal PA66
Pin header Copper, Tin plated
Wire guard Stainless steel
Cover Modified PPO
P.C.B Epoxy 1.6t
●Ferrule Selection
AWG/ (㎟) DIN46228 Other A(㎜) B(㎜) C(㎜)
20/0.5 White White/Orange 10.0 1.3 3.2
18/0.75 Gray Blue/White 10.0 1.5 3.4
17/1.0 Red Red/Yellow 10.0 1.7 3.6
●Method of removal wire ●Appropriate tool
'ULYHU
When using a stranded wire,
use a ferrule or a round type
terminal. In case of a solid wire,
use it without crimping tool.
Insert into the terminal block
without using a separate tool.
When disconnecting the wires,
keep the disconnect button
pressed with the driver (- type)
and disconnect the wires.

● SA-COM20
SA-COM20B
•Diagram
● SA-COM40
SA-COM40B
•Diagram
● SA-COM20D
•Diagram



+ROHRIIL[LQJ



-
+
---------
+++++++++
++
+
+
++++
---
++ --
-----





+ROHRIIL[LQJ

-
++
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+- +- --
+- ++ -- +- +- +
---
-
++
---- ---
+++++ +++++
63
56.2
5
43
•Dimension
•Dimension
•Dimension
• SA-COM20
• SA-COM20B
[Upper terminal]
[Lower terminal]
• SA-COM40
• SA-COM40B
NO.201510-OM-ENG-MC-01
■ HQ : 47035, 28, Daedong-ro, Sasang-gu, Busan
TEL : [phone] FAX : [phone]
■ SEOUL Office: 14353, M Cluster-707, 17, Deogan-ro
104beon-gil, Gwangmyeong-si, Gyeonggi-do
TEL : [phone] FAX : [phone]
Major products
■Relay terminal 1, 2, 4, 6, 8, 16, 32point
■Interface terminal 20, 24, 26, 34, 40, 50, 57, 40 x 2pole
■PLC I/O Connecting cables MITSUBISHI, LSIS, CIMON, OMRON, FUJI, YOKOGAWA, HITACHI, SIEMENS, AB, etc.
■Servo Connecting cables Encoder cable, Power cable, Motion cable / MITSUBISHI, YASKAWA, OMRON, PANASONIC, , LSIS, SAMSUNG, etc.
■Wiring harness / Special cable assembly
※The above specifications are subject to change without notice.
※Please contact HQ or branch office where you purchased product for A/S of this product or technique.
Precautions
1. Use within the specified rated voltage and current range.
2. Use in the specified temperature and humidity and avoid using it outdoors.
3. Wire according to the wiring diagram and cut off the power before working.
4. For suitable wire, use solid wire: 0.5~1.5㎡/ stranded wire: AWG 17~22,
and use the crimp terminal after confirming "Selection of Ferrule".
5. For long-term storage, avoid places with dust or gas or high humidity.
6. Since this product is a resin molded product, do not apply impact.
----------
----------
++++++++++
++++++++++