ipf H3, H3c User manual

BP070-504451-B
cover
Clasp
1 Halogen bulb check
2 Removing halogen bulb (see below as an example)
・LED bulb assy ……… 2
①
Check the condition of the halogen bulb attachment.
If the check cannot be done visually or the space is too narrow,
please remove the headlamp unit from the vehicle.
Refer to the vehicle's manual when changing or removing your halogen headlamp bulb.
Remove the lamp unit cover, unclasp and remove
the bulb.
Refer to the vehicle's manual for fog lamp removal
procedure, as it can differ between vehicles.
Components
Installation procedure
・ Cable ties
……… 4
Do not turn on the switch
if the bulb is not connected
LED bulb's power wire
(nonpolarity)
WARNING:
Vehicle's fog lamp
power wire
Halogen bulb
Halogen bulb
＜Test procedure＞
1. Remove the vehicle's power wire from
halogen bulb and connect to the LED bulb's
power wire.
2. Turn on the lamp, Test for correct lighting.
3. Check the vehicles gauges for any warning
signs. If no warnings, the test is finished.
LEDBulbInstallationManual
(H3, H3c)
LED bulb lighting test points
※Do it before installation.

LED bulb
Clasp
cover
②
3
Installing the LED bulb (see below as an example)
4 Connecting and fixing the harness and drive unit
Arrow
Arrow
Lock knob
Connect LED bulb's connector to drive unit's
connector.
LED bulb side Drive unit side
・ Insert the driver unit's connector into LED bulb's
connector, the arrows in a straight line.
Rotate the lock knob clockwise and tighten it
securely.
Prevent LED bulb's failure from water entry into
the joint part.
If the joint part is not locked securely, water
entry may result.
Caution
Insert the LED bulb into the fog lamp.
(opposite procedure of removing)
Advice
Vehicle's fog lamp wiring is NOT used in this
installation procedure.
Insulate the wiring using insulating tape etc. and
avoid contact with the LED bulb.
Advice
・Make a slit in the cover refer to the figure right.
・Making a hole or slit in the downside of the
cover to avoid dust and water entry.
・ Check the correct orientation of the bulb as its
socket has two different cutouts (round &
square-shaped).
・ Do not forcibly bend the wiring at all times.
Caution
・Water entry into the headlamp unit may result
in technical malfunction.
Make a hole in the cover or headlamp unit in order to
pass LED bulb's harness.
Pass the LED bulb's harness through the cover.
Apply caulking material to fill a gap in the cover to
avoid dust and water entry.
In the case of the cover attached at the rear of bulbs
Caution

Connect the vehicle's wiring to the LED bulb's wiring
using commercially available wiring connector.
Commercially available
wiring connector
connect
to ground
O
R
LED bulb's
power wire
③
Advice
・ Use water proof connector if you connect
wirings outside of the fog lamp unit.
・ Using non-water proof connectors may corrode
wirings.
Caution
Example of connecting using a connector
Vehicle's fog lamp wiring
・ LED bulb's power wire has no polarity and
AWG20.
・ Use appropriate size of connectors as
thickness of vehicle's fog lamp wiring can differ
between vehicles and fog lamps.
・ Connect to ground if vehicle's fog lamp with no
negative wiring.
Cable ties
Loop
Insert cable ties into the loops and fix them on
the vehicle's harness as shown in the image.
Verify that the LED bulb is secured tightly by
wobbling it. If you removed front bumper or other
parts, reinstall them into original positions.
Vehicle’s harness
Warning (prevent disconnecting)
Do not tie the harness together with the
drive unit.
Do not bend or pull the harness by
excessive power.
Leave a slack in the harness.
Harness's minimum bend radius
should be more than 20mm
(see the figure right).
More than 20mm
Fog lamp Minimum
bend radius
Harness should not be tense.
Leave a slack.

④
5
Lighting check and adjusting optical axis
Optical axis
Wall or screen
Wall or screen
Fog lamp centerline
Cut-off line (brightness boundary line)
Fog lamp
Advice
In general vehicles, rear wheel side sinks by
loading to trunk or getting into backseats.
It makes an optical axis upward.
This product is brighter than genuine halogen
fog bulb. Upward lighting by such optical axis
reduces proper fog lamp function. It may cause
a glare to oncoming or leading vehicles.
Assume that load capacity on backseats or trunk
and adjust to lower a cut-off line (brightness
boundary line) beforehand.
Turn on the engine. Switch on the head lamp. Check to see the LED bulb lights up properly.
Make adjustment to the optical axis refer to the figure below. Check to see if the fog lamp indicator
on the dash is lighting up properly.
Park your vehicle in a flat place. Turn on the fog lamp
towards a wall or screen. Adjust the optical axis so
that a cut-off line (brightness boundary line) comes
below the centerline of the fog lamp.
For more information about an optical axis adjustment
method, please check it with car maintenance books
you have or from your dealer.