IPmitter IPMIT450 User manual

Quick Start Guide - qIPMIT400 Copyright 2021 System Q Ltd
1
IPMITTER 5.8GHz 48V 900Mbps IP Bridge
IPmitter is a registered trademark of System Q Ltd
IPMIT450 / IPMIT400 - Quick Start Guide
www.systemq.com/pdf
/manual/xIPMIT400.pdf
The IPMIT400s can be used to "bridge" an wireless IP connection for IP cameras or other IP devices
wireless between two points, devices connect via the RJ45 port on the IPmitter.
Powering
Option 1 - Power from 12V DC (via the 2.1mm DC Socket), the current consumption is 300mA.
The IPMIT400 is polarity sensitive so connections must be made correctly.
Option 2 - Power the camera using 48V PoE, in the RJ45 WAN/POE Socket
The IPMIT400 will take approximately 1 minute to boot up.
1 = Function Button
2 = LED Display
3 = Setting
4 = 12V DC. 2.1mm DC Socket
5 = Reset/Pair Button
6 = WAN - 10Mbs / 100Mbs / 1000Mbs 48 PoE network socket
7 = LAN - 10Mbs / 100Mbs network socket
Standard WiFi Bridge Setup
For more setup options see the full manual

Quick Start Guide - qIPMIT400 Copyright 2021 System Q Ltd
2This symbol indicates that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated
WEE/CG0783SS collection point as defined by your local council.
All specifications are approximate. System Q Ltd reserves the right to change product specifications or featureswithout notice. Whilst every effort is
made to ensure that these instructionsare complete andaccurate, System Q Ltd cannot be held responsible for anylosses, no matter how they arise,
from errors or omissionsin these instructions, or the performance or non-performance of the equipment refered to.
IPMITTER 5.8GHz 48V 900Mbps IP Bridge
IPmitter is a registered trademark of System Q Ltd
Available Channels – 36, 40, 44, 48
The IPmitters are sent out as default on C048 (Client and channel 48), and need pairing up before
installing. One IPmitter needs to be set to H (Host) and the other to C (Client), they both have to be set
to the same channel number.
Example - Pairing on channel 48
1. Press the F (function) button and "C" will flash. Pressthe S (setting) button to change to "H048"
2. Press the F button 4 times to move across the display, then the whole display will flash for about 5
seconds to indicate the settings have been saved.
3. Now press the RST (reset) button for 1 second on both IPmitters. The display will change to a P with a
rotating segment whilst pairing and will show P and a value once paired. Pairing can take up to 2
minutes.
The strength will range P-01 (Good) to P-75 (Poor). If P-95 shows then the IPmitters have not paired.
To add more clients (up to 4) to one host then set the channel on the new client and press the reset
buttons on the new client and the Host.
www.zipdvr.com/howto/TIP459
-How-To-Add-IP-Cameras.html
If using the IPMIT400 with a ZIP Recorder then the
cameras needs to be manually configured, scan the QR
code to the left for the "how to guide"
LAN Port 1 Speed
10Mbs / 100Mbs
LAN Port 2 Speed
10Mbs / 100Mbs / 1000Mbs
Frequency
5.8Ghz
Wireless Data Speed
900Mbps
Wireless Standard
IEEE802.11AC/A
PoE Voltage
48V
12V Input Option
Yes
Max Tx Distance
2000m (Recommend 1000m)
Easy Pair Technology
Yes
Support 1 - 1
Yes
Support 1 - Many
Yes
Modes
Access Point / Bridge / Repeater
Mounting
Wall Or Pole (Not Supplied)
Dimensions
260 x 88 x 56mm