Edimax ECS1100 Series Programming manual

Web Management Guide
www.edge-core.com
ECS1100 Series
Release v1.0.1.0

Web Management Guide
ECS1100-5P
L2 Gigabit Ethernet Web Managed PoE Switch
with 4 1000BASE-T RJ-45 PoE+ (30W) Ports,
and 1 1000BASE-T RJ-45 Port
ECS1100-10HP
L2 Gigabit Ethernet Web Managed PoE Switch
with 4 1000BASE-T RJ-45 PoE++ (90W) Ports,
4 1000BASE-T RJ-45 PoE+ (30W) Ports,
and 2 100/1000M SFP Ports
E082023-CS-R01

– 3 –
How to Use This Guide
This guide includes detailed information on the switch software, including how to
operate and use the management functions of the switch. To deploy this switch
effectively and ensure trouble-free operation, you should first read the relevant
sections in this guide so that you are familiar with all of its software features.
Who Should Read
This Guide?
This guide is for network administrators who are responsible for operating and
maintaining network equipment. The guide assumes a basic working knowledge of
LANs (Local Area Networks), the Internet Protocol (IP), and Simple Network
Management Protocol (SNMP).
How This Guide is
Organized
This guide describes the switch’s web browser interface.
The guide includes these sections:
Section I “Getting Started” — Includes basic settings required to access the
management interface.
Section II “Web Configuration” — Includes all management options available
through the web browser interface.
Section III “Appendices” — Includes information on troubleshooting device
management access.
Related
Documentation
This guide focuses on software configuration through a web browser.
For information on how to install the switch and all safety information and
regulatory statements, see the following documents:
Quick Start Guide
Safety and Regulatory Information
Conventions The following conventions are used throughout this guide to show information:
Note: Emphasizes important information or calls your attention to related features
or instructions.

How to Use This Guide
– 4 –
Caution: Alerts you to a potential hazard that could cause loss of data, or
damage the system or equipment.
Warning: Alerts you to a potential hazard that could cause personal injury.
Revision History This section summarizes the changes in each revision of this guide.
August 2023 Revision
This is the first version of this guide. This guide is valid for software release
v1.0.1.0.

– 5 –
Contents
How to Use This Guide 3
Contents 5
Section I Getting Started 8
1 Using the Web Interface 9
Connecting to the Web Interface 9
Navigating the Web Browser Interface 10
Dashboard 10
Configuration Options 10
Saving the Configuration 11
Panel Display 11
Main Menu 12
Section II Web Configuration 13
2 System Management 14
System Information 14
IP Settings 15
Account Settings 17
System Time 18
Setting the Time Manually 18
Setting the Time Using SNTP 19
Cloud Manage 20
Jumbo Frames 21
3 Port Configuration 22
Port Settings 22
Storm Control 24

Contents
– 6 –
Port Speed Limit 25
Port Trunk 26
Port Statistics 28
SFP 29
4 VLAN Configuration 30
Static VLAN 30
VLAN Setting 31
5 QoS Configuration 33
QoS Basic 33
QoS Advanced 35
Port-Based Priority 35
802.1p-Based Priority 36
DSCP-Based Priority 37
Priority Queue Mapping 38
6 PoE Configuration 40
PoE Port Config 40
PoE System Power 42
PD Alive 43
PoE Timer Rule 44
PoE Timer Set 45
Poe Extend Mode 46
7 IGMP Configuration 48
IGMP Snooping 48
Router Port 49
Group Address 51
8 Tools 53
System Upgrade 53
Backup Restore 54
System Reset 56
System Reboot 56

Contents
– 7 –
Section III Appendices 58
A Troubleshooting 59
Problems Accessing the Management Interface 59
B License Information 60
The GNU General Public License 60

– 8 –
Section I
Getting Started
This section describes the basic settings required to access the management
interface.
This section includes these chapters:
“Using the Web Interface” on page 9

– 9 –
1Using the Web Interface
This switch provides an embedded HTTP web management interface. Using a web
browser you can configure the switch and view statistics to monitor network activity.
The web management interface can be accessed by any computer on the network
using a standard web browser.
Connecting to the Web Interface
Prior to accessing the switch from a web browser, be sure you have first performed
the following tasks:
1. The default IP address and subnet mask for the switch is 192.168.2.10 and
255.255.255.0, with no default gateway. If this is not compatible with the
subnet connected to the switch, you can configure it with a valid IP address,
subnet mask, and default gateway.
2. Set user names and passwords. Access to the web interface is controlled by a
default user name and password. For security reasons, you should change the
default password and configure new user accounts as soon as possible. (See
“Account Settings” on page 17.)
3. After you enter a user name and password, you will have access to the web
management interface.
Note: Users are automatically logged off of the web server if no input is detected
for 600 seconds.

Chapter 1 | Using the Web Interface
Navigating the Web Browser Interface
– 10 –
Navigating the Web Browser Interface
To access the web-browser interface you must first enter a user name and
password. The administrator has read/write access to all configuration parameters
and statistics. The default user name and password for the administrator is
“admin.” The administrator has full access privileges to configure any parameters
in the web interface. Refer to “Account Settings” on page 17 for more details.
Dashboard When your web browser connects with the switch’s web agent, the Dashboard is
displayed as shown below. The Dashboard displays the main menu on the left side
of the screen and System Information on the right side. The main menu links are
used to navigate to other menus, and display configuration parameters and
statistics.
Figure 1: Dashboard
Configuration
Options
Configurable parameters have a dialog box or a drop-down list. Once a
configuration change has been made on a page, be sure to click on the Apply
button to confirm the new setting.
The following table summarizes some common web page configuration buttons.
Table 1: Web Page Configuration Buttons
Button Action
Sets specified values to the system.
Selects all entries in a table.
Deletes the selected items.