iquatics aqualumi Universal User manual

TIGHTENINGSCREW
[email protected]
WWW.IQUATICS.CO.UK
THANK YOU FOR PURCHASING THE IQUATICS AQUALUMI UNIVERSAL
THE FUTURE OF AQUARIUM LIGHTING
FITTING FLAPS
The AquaLumi Universal has been
designed to incorporate your existing
aquarium covering flap set. The lighting
system should be positioned so that the flap
set fully covers the aquarium. Your existing
flap set will determine where the installation
point should be.
For aquariums without a flap set the unit
can be positioned wherever required.
If required the AquaLumi Universal can be
extended to fit your aquarium. Simply
unscrew the plastic screw located on the
top of each of the end caps, slide out the
extension brackets to the required length
and tighten the screw back up.
Be sure not to over-tighten the screw.
Each side will extend upto 50mm.
Maximum extension - 100mm
Please see table below for product
specification.
MAX 50MM
MODEL REPLACEMENT MIN MAX DIMENSIONS
SPECIFICATION TUBE LENGTH LENGTH WX H(MM)
Aqualumi Universal 550mm 24w (435mm) 533mm 633mm 83 x 52
Aqualumi Universal 600mm 24w (435mm) 593mm 693mm 83 x 52
Aqualumi Universal 700mm 24w (550mm) 693mm 793mm 83 x 52
Aqualumi Universal 800mm 28w (590mm) 793mm 893mm 83 x 52
Aqualumi Universal 920mm 35w (742mm) 903mm 1003mm 83 x 52
Aqualumi Universal 1000mm 39w (850mm) 993mm 1093mm 83 x 52
Aqualumi Universal 1200mm 54w (1047mm) 1180mm 1280mm 83 x 52
Aqualumi Universal 1500mm 54w (1200mm) 1480mm 1580mm 83 x 52

DRIP LOOP (FIG 1)
DIAGRAM 1
1 12 2
Please read the set of instructions carefully before operation.
iQuatics AquaLumi Universal lighting system has been designed and manufactured by industry
veterans and we are proud to present you with our latest high quality finished product. Always make
sure the instructions are followed precisely; do not operate your appliance if there are any signs of
damage or malfunction. If damaged, maintenance should be carried out by the manufacturer or a
qualified person. This is to avoid any permanent damage to your fixture.
As with all aquarium electronic equipment, make sure you have a drip loop to prevent the socket or
plug from getting wet. As shown in (fig 1), opposite, the part of the
power cable lying below the level of the socket is used to prevent
the water entering the socket.
Make sure your pendant is safely out the reach of children, unless
accompanied by adult supervision, as injury may occur from hot
parts, the lamp, or moving parts. This lighting system should only
be used for its intended purpose. It must be installed indoors and
not exposed to the weather, freezing temperatures or close to other
heat sources and never submerged in water.
IMPORTANT
1. LAMP INSTALLATION
If you ordered fluorescent tubes with your Aqualumi Universal, your bulbs were removed and
packaged safely to prevent damage in transit. Never operate your Aqualumi Universal if there is any
visible damage to the system or bulbs on arrival.
1.1 INSTALLATION LOCATION
Ideally your light unit will be located next to an adequately rated electricity supply. If you are using an
extension lead please make sure the lead is not overloaded.
1.2 WORKINGSPECIFICATION
220v-240v (Fluctuation) Ambient working temperature +65 degrees C.
Your Aqualumi Universal should be installed in dry conditions away from the outside weather and
corrosive materials. Frequently wipe down your lighting system of any residue which maybe have
built up over time.
Under no circumstances should your lighting system be submerged under the water.
Minimum distance from the water surface is 20mm.
1.2 REPLACING / INSTALLING YOUR FLUORESCENT TUBES
Make sure your light unit is unplugged from the power supply before changing any fluorescent tubes.
TIP Change the bulbs at the time of day at which your lighting is not in use, saving you having to disturb
the timing of your aquarium lighting and ensuring the unit is fully cool.
TIPFluorescent tubes can be very fragile. Please be careful when removing the bulb from the packaging.
Your Aqualumi Universal will have either a single
power cable or a double power cable. Depending
on the model which you have purchased. The 2
tube Universal is fitted with a single power cable
which controlls both tubes at the same time. Both
tubes need to be installed for the fixture to work.
With the 4 tube Aqualumi bar there will be 2
power supplies. One will control tube 1 and 4 and
the other will control 2 and 3 giving more control
over the timing of your lights. See Diagram 1.
DIAGRAM 2
Seals and washer are shown in red for illustration purposes.
SCREW CAPS
STEP 2
Each Lamp receiving connector
has 2 washers/seals. Place Seal 1
into positing over the thread of the
connector making sure it is seated
against the flat surface.
STEP 3
Simultaneously carefully push
the ends of the tubes into the
receiving pins on the
connectors. These will click
into place when seated
correctly.
STEP 4
Tighten the screw cap onto the
receiving thread. This will be
quite tight due to the material
and thread to allow for the
water tight seal. Do not use a
spanner on this. They should
be tightened by hand.
STEP 1
Place two screw caps onto each tube as shown in the below
illustration.
Repeat steps 1-4 on all the tubes that you are placing into your setup.
Carefully slide seal 2 onto each
end of the fluorescent tube aligning
it up to the outer edge of the metal
end cap as shown here.
The rubber seals are important to
create a water tight seal.
Seal 1
Seal 2