iSystem IC50130 User manual

Legacy Debug Adapters V1.1
User Manual

This document and all documents accompanying it are copyrighted by iSYSTEM AG and all
rights are reserved. Duplication of these documents is allowed for personal use. In all other
cases, written consent from iSYSTEM is required.
Copyright iSYSTEM AG.
All rights reserved.
All trademarks are property of their respective owners.
iSYSTEM is an ISO 9001 certified company.
www.isystem.com

Contents
Introduction................................................................................................................................. 1
26-pin 2.54 mm NXP ColdFire Debug Adapter............................................................................. 2
6-pin 2.54mm NXP BDM Debug Adapter ..................................................................................... 4
6-pin 2.54mm NXP S12Z BDM Debug Adapter ............................................................................ 5
16-pin 2.54mm NXP COP Debug Adapter .................................................................................... 6
38-pin Mictor PPC4xx RISCTrace D. Adapter................................................................................ 8
16-pin 2.54mm Renesas 78K0R D. Adapter ............................................................................... 10
26-pin KEL Renesas V850 Debug Adapter.................................................................................. 12
10-pin 2.54mm Renesas 78K0 Debug Adapter .......................................................................... 14
78K0 16-pin 2.54mm Adapter........................................................................................... 15
14-pin 2.54mm Renesas RL78 Debug Adapter........................................................................... 16
4-pin ERNI ST STM8 Debug Adapter .......................................................................................... 18

1
Introduction
The iC5000 and the iC5700 BlueBox adapt to the specific target architecture and target debug
connector through a dedicated debug adapter.
This document provides detailed information on the debug adapters (used in conjunction with
the iC5000 or the iC5700) supporting legacy microcontroller architectures which are no longer
supported with winIDEATM 9.17.0 or newer.
Listed debug adapters and belonging microcontroller architectures are supported with
winIDEATM 9.12.288 or older.
Detailed information on current debug adapters which are used in conjunction with the iC5000
and the iC5700 BlueBox, and supported by winIDEATM 9.17.0 or newer, is available in a
separate user manual.
Ordering Code
Description
IC50130
26-pin 2.54 mm NXP ColdFire Debug Adapter
IC50140
6-pin 2.54mm NXP BDM Debug Adapter
IC50141
6-pin 2.54mm NXP S12Z Debug Adapter
IC50153
16-pin 2.54mm NXP COP Debug Adapter
IC50155
Mictor 38-pin PPC4xx RISCTrace Debug Adapter
IC50170
16-pin 2.54mm Renesas 78K0R Serial Debug Adapter
IC50172
26-pin KEL Renesas V850 Debug Adapter
IC50174
10-pin 2.54mm Renesas 78K0 NXP Debug Adapter
IC50175
14-pin 2.54mm Renesas RL78 NXP Debug Adapter
IC50190
4-pin ERNI ST STM8 Debug Adapter
For more information contact our sales team via sale[email protected]
This symbol is used within the manual to highlight important safety notices.

2
26-pin 2.54 mm NXP ColdFire Debug Adapter
Ordering code
IC50130
This debug adapter is used to connect the iC5000 BlueBox to NXP ColdFire based target
featuring a 26-pin 2.54 mm pitch target debug connector with the ColdFire pinout.
This debug adapter is supported by the iC5000 BlueBox only. The iC5700 doesn’t
support the ColdFire architecture.
The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to
the target debug connector on the other side. Refer to the BlueBox User Manual for more
details on connecting the debug adapter.
The following pinout is valid on the target side:
Signal direction
Signal
Pin
Pin
Signal
Signal direction
I
Developer Reserved
1
2
~BKPT
O
GND
3
4
DSCLK
O
GND
5
6
Developer Reserved
RESET
7
8
DSI
O
I
VDD_IO
9
10
DSO
I
GND
11
12
PSTDDATA7
I
I
PSTDDATA6
13
14
PSTDDATA5
I
I
PSTDDATA4
15
16
PSTDDATA3
I
I
PSTDDATA2
17
18
PSTDDATA1
I
I
PSTDDATA0
19
20
GND
Motorola Reserved
21
22
Motorola Reserved
GND
23
24
PSTCLK
I
I
NC
25
26
~TEA
O
26-pin ColdFire target pinout
Blue colored signals are trace signals.

3
When connecting the BlueBox to the new embedded target for the first time, double
check that the debug adapter pinout matches with the target debug connector. Note
that a mismatch can result in a hardware failure.
26-pin 2.54 mm NXP ColdFire Debug Adapter features resettable fuses on pins 2, 4, 7, 8, 9, 10,
24 and 26. These protect debug signals against overcurrent and cycle back to a conductive
state after the excessive current fades away. Signals on pins 1, 12-19 and 24 are protected via
47 ohm serial resistors.
The debug adapter connects to the target via a 26-pin 2.54 mm connector, for example
Yamaichi FAS-26-17. A target should feature a matching part, for example WÜRTH ELEKTRONIK
61202621621.

4
6-pin 2.54mm NXP BDM Debug Adapter
Ordering code
IC50140
This debug adapter is used to connect the iC5000 and the iC5700 BlueBox to NXP HCS08, HC12,
HCS12, S12X and ColdFire V1 based target featuring 6-pin 2.54mm pitch target debug
connector with the BDM pinout.
The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to
the target debug connector on the other side. Refer to the BlueBox User Manual for more
details on connecting the debug adapter.
The following pinout is valid on the target side:
Signal direction
Signal
Pin
Pin
Signal
Signal direction
I/O
BGND
1
2
GND
NC
3
4
RESET
I/O
NC
5
6
VTref
I
6-pin BDM pinout
When connecting the BlueBox to the new embedded target for the first time, double
check that the debug adapter pinout matches with the target debug connector. Note
that a mismatch can result in a hardware failure.
6-pin 2.54mm NXP BDM Debug Adapter features resettable fuses on pins 1, 2, 4 and 6. These
fuses protect debug signals against overcurrent and cycle back to a conductive state after the
excessive current fades away.
The debug adapter connects to the target via a 6-pin 2.54 mm connector, for example FCI
71600-006LF. A target should feature a matching part, for example WÜRTH ELEKTRONIK
61200621621.

5
6-pin 2.54mm NXP S12Z BDM Debug Adapter
Ordering code
IC50141
This debug adapter is used to connect the iC5000 and the iC5700 BlueBox to NXP S12Z based
target featuring 6-pin 2.54mm pitch target debug connector with the S12Z BDM pinout.
The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to
the target debug connector on the other side. Refer to the BlueBox User Manual for more
details on connecting the debug adapter.
The following pinout is valid on the target side:
Signal direction
Signal
Pin
Pin
Signal
Signal direction
I/O
BGND
1
2
GND
I
PDO
3
4
RESET
I/O
I
PDOCLK
5
6
VTref
I
6-pin S12Z BDM pinout
When connecting the BlueBox to the new embedded target for the first time, double
check that the debug adapter pinout matches with the target debug connector. Note
that a mismatch can result in a hardware failure.
6-pin NXP BDM Debug Adapter features resettable fuses on pins 1, 2, 4 and 6. These fuses
protect debug signals against overcurrent and cycle back to a conductive state after the
excessive current fades away. Signals on pins 3 and 5 are protected via 47 ohm serial resistors
The debug adapter connects to the target via a 6-pin 2.54 mm connector, for example FCI
71600-006LF. A target should feature a matching part, for example WÜRTH ELEKTRONIK
61200621621.

6
16-pin 2.54mm NXP COP Debug Adapter
Ordering code
IC50153
This debug adapter is used to connect the iC5000 BlueBox to NXP MPC6xx, MPC82xx,
MobileGT, MPC7xx or MPC83xx based target featuring 16-pin 2.54mm pitch target debug
connector with NXP COP pinout.
This debug adapter is supported by the iC5000 BlueBox only. The iC5700 doesn’t
support the listed architectures.
The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to
the target debug connector on the other side. Refer to the BlueBox User Manual for more
details on connecting the debug adapter.
The following pinout is valid on the target side:
Signal direction
Signal
Pin
Pin
Signal
Signal direction
I
TDO
1
2
QACK#
O
O
TDI
3
4
TRST
O
I
HALTED
5
6
VTref
I
O
TCK
7
8
CKSTP_IN
O
O
TMS
9
10
NC
O
SRESET
11
12
GND
O
HRESET
13
14
NC
I
CKSTP_OUT
15
16
GND
16-pin COP target pinout
When connecting the BlueBox to the new embedded target for the first time, double
check that the debug adapter pinout matches with the target debug connector. Note
that a mismatch can result in a hardware failure.

7
16-pin 2.54mm NXP COP Debug Adapter features resettable fuses on all pins except for the pin
15. These protect debug signals against overcurrent and cycle back to a conductive state after
the excessive current fades away. The signal on the pin 15 is protected via 100 ohm serial
resistor.
The debug adapter connects to the target via a 16-pin 2.54 mm connector, for example
Yamaichi FAS-1601-2101-2-OBF. A target should feature a matching part, for example WÜRTH
ELEKTRONIK 61201621621.