iTaste MVP3.0 User manual

USER MANUAL
USER M ANUAL
iTaste MVP3.0 说明书 尺寸：65*104mm 封面材质：157g 双铜板纸单面过哑胶 内页材质：128g 双铜纸双面印刷 装订方式：胶装

1
Congratulaons on your purchase of this Innokin iTaste MVP3.0 Advanced Personal Vaporizer.
For the best possible vaping experience please carefully read, and follow this user manual.
The iTaste MVP3.0 is the newest in the line of internaonally bestselling iTaste MVP
vaporizers. The iTaste MVP3.0 features a greater range of Variable Voltage, Variable Waage,
advanced safety features, portable electronics charging capacity and also ‘Vape while
charging’ Technology.
The iTaste MVP3.0 has a flush 510 connecon with a spring loaded posive pin, durable
stainless steel threading, an included ego adaptor and a replaceable integrated micro-USB
charging cable.
The iTaste MVP3.0 has a variable voltage range of 3.0 – 9.0 volts adjustable in .1 volt
increments and a variable waage range of 6.0 – 30.0 Was, adjustable in .5 was increments.

WARNING:
3
The iTaste MVP3.0 uses Vrms DC current and is very accurate with a power deviaon of 0.1
Wa. The full 30 Was is precisely maintained between resistances of 0.4 to 2.5 ohms. There
is no wasted power and exact accuracy means you are always vaping the power level that you
choose. Vrms provides superior precision in delivering the exact waage Ohm’s Law requires
and stable power means beer vapor.
Please check and verify that your iTaste MVP3.0 is an authenc Innokin Technology product.
To verify that this iTaste MVP3.0 is a real Innokin Technology device please:
1) Find the label on the reverse of the packaging and scratch the silver stripe to reveal your
iTaste MVP3.0 Unique Authorizaon number.
2) Visit the Official Innokin Technology website at www.innokin.com
3) Enter the Unique Authencaon number in the Authencaon field.
4) Verify your iTaste MVP3.0 is authenc.
If you have any quesons or suggesons we would like to invite you to please write to us at
[email protected].
Join our Innokin FaceBook Page: www.facebook.com/Innokin.Technology for the latest
informaon, contests, giveaways and be part of a great and growing community!
3
2
Please read this secon carefully to ensure you receive maximum benefits from your iTaste
MVP3.0 and enjoy vaping with it in the most safe and effecve ways possible.
1. This Advanced Personal Vaporizer may be used with e-liquids that contain nicone. If
quesons or concerns regarding your e-liquid arise, please check with your e-liquid
provider. This product is only intended for use by adults of legal smoking age (18+) and
should not be used by children, women who are pregnant or breaseeding, or persons with
or at risk of heart disease, high blood pressure, diabetes or taking medicine for depression
or asthma, or who otherwise may be sensive to nicone. Nicone is addicve and habit
forming, and can be toxic by inhalaon, in contact with the skin or eyes, or if swallowed.
Ingeson of the non-vaporized concentrated e-liquid ingredients can be poisonous. Keep
away from children and pets.
2. This Advanced Personal Vaporizer may be used with e-liquids that contain nicone, a
chemical known to the State of California to cause birth defects or other reproducve harm.
Please check with your e-liquid provider. (For products sold in California.)
3. This Advanced Personal Vaporizer is only designed to be used with high quality e-liquid.
Please check with your e-liquid provider. This device is not intended for use with loose
tobacco leaf or herbal substances.

4. This Advanced Personal Vaporizer has not been evaluated by the Food and Drug Administraon
and is not intended to treat, migate, prevent or cure any disease or condion. This product
is not intended for use as a smoking cessaon device.
5. The clearomizer must be stored out of the reach of children and pets. All empty clearomizers
must also be disposed of properly and out the reach of children and pets.
6. This iTaste MVP3.0 Advanced Personal Vaporizer includes small parts such as the mouth
piece. Always keep any small parts out of reach of children and pets to prevent swallowing
or other harm.
7. Do not misuse, mishandle or store your iTaste MVP3.0 Advanced Personal Vaporizer
improperly. Even though it is made of high quality stainless steel it may become damaged
when dropped or otherwise mishandled.
8. Do not aempt to repair the unit by yourself as damage or personal injury may occur.
9. In order to guarantee the normal funconing of your iTaste MVP3.0 Advanced Personal
Vaporizer, and maximize vaping pleasure, we strongly advise that you charge the baery
when the power level drops below 10 percent.
10. In order to prolong the operaon of your iTaste MVP3.0 Advanced Personal Vaporizer,
please do not place or store this iTaste MVP3.0 Advanced Personal Vaporizer in excessively
hot or cold environments.
11. Obey local laws or regulaons regarding Electronic Cigarees when vaping. If you are in an
area where there are any bans or potenal dangers, please do not use your iTaste MVP3.0
Advanced Personal Vaporizer.
12. Your iTaste MVP3.0 Advanced Personal Vaporizer is not waterproof. Keep it dry at all mes.
13. Do not allow any liquids or ejuice to enter the device through the top threading or the USB
ports. If any liquids enter the device, or come into contact with the PCB, please disconnue
using or charging the device and contact your local Authorized Innokin Vendor immediately.
14. Keep your iTaste MVP3.0 Advanced Personal Vaporizer away from sources of excessive
heat as damages may occur.
15. Do not drop, throw, or mishandle your iTaste MVP3.0 Advanced Personal Vaporizer as the
outer shell or inner components may become damaged.
16. Innokin Technology is not responsible for baery and charger explosions, or malfuncons,
due to the use of a low-quality charger. Only use the original iTaste MVP3.0 Advanced
Personal Vaporizer starter kit charger to charge your iTaste MVP3.0, We strongly
recommend that you always use a high quality 5V 500mA USB wall charger (CE/UL
Cerfied). The iTaste MVP3.0 is not designed for use with a car charger, The iTaste MVP3.0
does not come included with a car charger.
17. Innokin Technology is not responsible for any clearomizer or baery damage due to the use
of low quality eLiquid or dry herb.
5
5
4

7
1 Connector
2 Firing, POWER ON,
POWER OFF buon
3 OELD Display Screen
4 “+” buon: MVP3.0 /VW+
“-” buon: MVP3.0 /VW-
5 Micro USB cable plug port
6 Baery level Indicator
4
5
3
2
1
6
7
6
The Primary Features of The iTaste MVP3.0
Baery Level Indicator:
The iTaste MVP3.0 baery has a tri-color LED on the top.
Green = Almost fully Charged. When the iTaste MVP3.0 is fully recharged the LED light will
power off.
Yellow = Half Power.
Red = Low Power. Charge the iTaste MVP3.0.
Variable Voltage:
Voltage can be adjusted from 3.0 – 9.0 volts in .1 volt increments.
Variable Waage:
Waage can be adjusted from 6.0 – 30.0 Was in .5 was increments.

2 . 5Ω
0.0W V
4.0
2 . 5Ω
0.0W V
Short Circuit/Atomizer Protecon:
Short Circuit/Atomizer Protecon protects the iTaste MVP3.0 Advanced Personal Vaporizer
against shorted atomizers and will stop the unit from funconing in unsafe condions.
The iTaste MVP3.0 features automac real-me atomizer Ohms detecon. If the resistance of
the atomizer is lower than 0.4, the Ohms bar will blink and the iTaste MVP3.0 will not power
on.
If there is a short circuit the iTaste MVP3.0 screen will display:
The LED light will power off. If there is a short circuit the MVP3.0 will not power on.
Over-Discharge Protecon:
The iTaste MVP3.0 Advanced Personal Vaporizer monitors the baery voltage and will
automacally power off when the baery over discharged.
0. 2Ω
0.0W V
4.0
0. 0Ω
0.0W V
4.0
9
8
ON/OFF baery switch:
Press the power buon“ ”three mes to turn on the iTaste MVP3.0. Once the iTaste MVP3.0
is on, hold down the power buon to acvate the atomizer. When the iTaste MVP3.0 is not in
use, press the power buon “ ” three mes in succession to power off the iTaste MVP3.0.
Always power off the iTaste MVP3.0 when it is not being used, or when it is going to be stored
in a pocket, bag or purse.
SAFETY:
15 second cutoff:
If the “ ” buon is held for 15 seconds or longer the iTaste MVP3.0 Advanced Personal
Vaporizer will stop firing unl the “ ” buon is released and pressed again.
Low Voltage Warning
The Red LED and Baery bar will connue blinking when the baery capacity is lower than 3.3V and
the iTaste MVP3.0 Advanced Personal Vaporizer will automacally power off.

‘Vape while charging’ Technology
The iTaste MVP3.0 is recharged with a Micro USB cable. When plugged into a power source the
iTaste MVP3.0 can also be vaped and charged at the same me with Innokin Technology’s
‘Vape while you charge’ pass-through technology.
Remembers last Voltage or Waage seng:
When the iTaste MVP3.0 is turned off it will remember the current voltage or waage seng
and it will retain the seng when the iTaste MVP3.0 is powered on.
Portable power source for electronic products
To charge your portable electronic device with the iTaste MVP3.0 plug the built-in Micro USB
cable into the electronic device and power on the iTaste MVP3.0. The included iTaste MVP3.0
starter kit charging cable can also be used. Plug the larger USB port into the iTaste MVP3.0 and
the Micro-USB into the electronic device and power on the iTaste MVP3.0. You may only
charge one electronic device at a me. Do not aempt to charge more than one device at the
same me or you may damage the device.
High compability 510 connector:
The iTaste MVP3.0 510 threading is compable all standard 510 clearomizers & atomizers
including the iClear16, iClear16B, iClear16D, iClear30, iClear30B, iClear30S and the Gladius-X.
Ego Threading Adapter
Aach the provided EGO Thread adapter to the flush 510 connector to vape with ego style
compable tanks.
The iTaste MVP3.0 has three buons: “ ” buon, "+" buon and "-" buon.
“ ” buon: Power
“+” buon: MVP3.0 / VW+
“-” buon: MVP3.0 / VW- 11
10
OPERATION GUIDE

All iTaste MVP3.0 sengs can be easily changed without the use of a menu system. The large
OLED screen readily displays all important informaon.
To POWER ON the iTaste MVP3.0:
Press the buon “ ” three mes to power on the iTaste MVP3.0.
The LED light on the top will blink once to display the current baery charge. When the
buon “ ” is pressed (with a clearomizer aached) the OLED screen will display the aached
atomizer resistance, voltage and waage and remaining baery charge.
To POWER OFF the iTaste MVP3.0:
Ohms Meter & Baery Level Indicator & Puff Counter:
With an atomizer aached, hold both the “+” and “-” buons simultaneously and the screen
will display: the resistance of the aached atomizer, the baery voltage, the number of puffs
since the device was last turned off and the last set voltage or waage.
Enter Variable Waage Mode:
Press and hold the “+” buon and then the “ ” buon for 1 second to enter variable waage
mode.
Adjust Variable Waage:
When the iTaste MVP3.0 is in variable waage mode press the “+” or “-” buon one me and
then press it again to decrease the waage. Hold the buon down to quickly increase or
decrease the set waage.
The iTaste MVP3.0 waage can be adjusted from 6.0 to 30 was in .5 wa increments by
pressing the “+” or “-” buons. If the waage is decreased below 6 Was it will cycle up to 30
Was. If the waage is increased from 30Was it will cycle down to 6 was. Press the
buon “ ” to lock the set waage and fire the iTaste MVP3.0.
2.5Ω
3.7V 10
13
12
2 . 5Ω
0.0W
10.0W
2 . 5Ω
0.0W
W
4.
0

Enter Variable Voltage Mode:
Press and hold the “-” buon and then the “ ” buon for 1 second to enter variable voltage
mode.
In variable voltage mode the iTaste MVP3.0 voltage can be adjusted from 3.0 to 9.0 volts in .1
volt increments by pressing the “+” or “-” buons.
Adjust Variable Voltage:
When the iTaste MVP3.0 is in variable voltage mode press the “+” or “-” buon one me and
then press it again to decrease the voltage. Hold the buon down to quickly increase or
decrease the set voltage.
The iTaste MVP3.0 voltage can be adjusted from 3.0 to 9.0 volts in .1 volts increments by
pressing the “+” or “-” buons. If the voltage is decreased below 3 volts it will cycle up to 9
Volts. If the voltage is increased from 9 Volts it will cycle down to 3 volts. Press the buon“ ”
to lock the set voltage and fire the iTaste MVP3.0.
Important: Explaining Low-Resistance / High Waage Vaping
To ensure you have the best possible vaping experience it is important to have a basic
understanding of waage, voltage and coil resistance. There is a range of standard coil
resistances: 2.1, 1.7, 1.4, 1.1, 0.8, 0.5 ohm etc and Rebuildable Atomizers or Drippers
(RBA/RDA) may even be lower. The iTaste MVP3.0 can fire between resistances of 2.5 to .4
ohm and you can clearly see the resistance of the aached clearomizer on the OLED screen.
We would suggest that for coil resistances of 1.7 – 2.1ohm you can begin with a seng of
8Was and then increase the Waage unl you find your perfect seng. For resistances of 0.5
you can try a seng of 25Was and increase the waage unl you find your perfect vaping
seng.
We would suggest that for coil resistances of 1.7 – 2.1ohm you can begin with a seng of 4.0
Volts and then increase the Voltage unl you find your perfect seng. For resistances of 0.5
you can try a seng of 5 Volts and increase the voltage unl you find your perfect vaping
seng.
If you have any quesons please contact your local Authorized Innokin Vendor.
Important: The iTaste MVP3.0 will only fire variable voltage OR variable waage depending on
the last seng chosen; it will not fire both. You must choose either Variable Voltage or
Variable Waage.
2 . 5Ω
0.0W V
4.0
15
14

Charging the iTaste MVP3.0
You can rely on your iTaste MVP3.0. This iTaste MVP3.0 is built with the highest quality of
engineering and materials and is built to be your perfect daily vaping device. The iTaste
MVP3.0 is legendary for being a tough, dependable, long lasng vaporizer however life can be
rough and it may become damaged. This is true of any electronic devices and the iTaste
MVP3.0 seems to get dropped a lot more than most.
For maximum safety we strongly recommend:
Charge the device using the provided micro-USB cable. Do not use a low quality cable.
Do not use a car/truck usb adapter to charge the iTaste MVP3.0.
We strongly recommend that you are present when the device is being charged.
Do not leave it charging unaended.
OR
PLEASE NOTE:
The Red LED will blink for eight seconds when baery capacity is lower than 3.3V and the iTaste
MVP3.0 will automacally power off.
When the iTaste MVP3.0 baery is fully charged the LED will power on and the device will power
off.
17
16