J-Tech Digital JTD-416 User manual

JTD-416 | JTECH-KVE3
VGA KVM Extender over Ethernet

Introduction
The JTECH-KVE3 VGA KVM Extender is a bundled kit including both a local transmitter and a remote
receiver unit. The KVM extender offers a complete solution for scenarios in which remote monitor
displays are required and the ability to view and split your source VGA signal to two independent
displays is necessary. The JTECH-KVE3 allows you to extend your VGA video signal up to 985 feet
via standard CAT6 UTP cable. The JTECH-KVE3 also simultaneously transmits USB 2.0 high speed
data and control signals making it perfect for easily controlling your video source from your video
destination.
Features
* VGA video and KVM signals are transmitted over long distances (up to 985 feet) via Cat5/6
UTP network cable
* Supports high-definition video resolutions up to 1920 x 1080 and 1920 x 1200
* Supports remote keyboard & mouse signal transmission (2 x USB 2.0 ports at Receiver)
* VGA Standard Compliance
* Able to automatically identify and configure various display modes
* Built-in manual brightness and contrast settings for fine-tuning image quality
* Built-in ESD electrostatic protection circuit
* Simple and convenient “plug & play” installation
Package Contents
•J-Tech Digital JTECH-KVE3 (Transmitter + Receiver)
•2 x Power Adapter DC5V 1A
•4 x Mounting Brackets & Screws

Ports and Interfaces
① DC 5V: DC 5V Power Adapter In
② PC IN: Connect to PC Host in via USB-A to USB-B Cable
③ VGA IN: Connect to Input Source Device via VGA Male Cable
④ CAT5e/6: Connect to CAT5e/6 cable between transmitter and receiver
⑤ POWER: Power Status LED Indicator
⑥ VGA OUT: Connect to display via VGA Male Cable (Transmitter – Local Loop Out Display |
Receiver – Remote Out Display)
⑦ K/M: Connect to USB 2.0 peripheral devices such as keyboard, mouse, printer or USB storage
device
⑧
: Rotate dial to adjust the contrast
: Rotate dial to adjust the brightness
Transmitter
Receiver

Connection Diagram
Specifications
Note: Specifications are subject to change without notice.
Input Ports
VGA x 1 (DB15 Female) | USB-A x 2
Output Ports
VGA x 2 (DB15 Female) | USB-B x 1
Extension Distance
985 Feet (VGA & USB)
USB Transmission rate
480 Mbps
USB Standard
USB 2.0
Vertical Frequency Range
60 / 75 / 85Hz
Supported PC Resolutions
640 x 480 | 800 x 600 | 1024 x 768 | 1280 x 720 | 1280 x
768 | 1280 x 960 | 1280 x 1024 | 1600 x 900 | 1600 x 1200
| 1920 x 1080 | 1920 x 1200
Operating Temperature
32°F to 122°F
Storage Humidity
5% to 90% RH non-condensation
Power Supply
DC 5V 1A
Power Consumption (Max)
Transmitter - 1.5W | Receiver - 2.5W
Extender Unit Certification
FCC | CE | RoHS
Power Supply Certification
FCC | CE | RoHS
Dimensions (LxWxH)
3.72 x 2.75 x 0.98 in
Net Weight
Transmitter – 0.39 Lbs.| Receiver – 0.38 Lbs.
Material
Metal

Troubleshooting
Problem
Cause
Solution
Power LED is off and product
is not working
A power adapter is not
properly connected or VGA
source device is not on
Please check if the power
adapter is connected properly
and securely on both
transmitter and receiver.
Ensure the VGA source device
is powered on
Intermittent video signal or
noise/snow in image
VGA cable and CAT5e/6 may
not be in working condition or
the cable is too long
Please use standardized VGA
and UTP cable only. Cable
length should not exceed 49.2
FT (VGA) | 985 FT (UTP CAT6)
Connected USB storage device
is not working correctly
The external storage device
power consumption is higher
than 2.5W (5V 500mA)
Please use a storage device
with power consumption less
than 2.5W
Warranty
If your product does not work properly because of a defect in materials or workmanship, J-Tech
Digital (referred to as "the warrantor") will, for the length of the period indicated as below, (Parts
(1) Year, Labor (90) Days) which starts with the date of original purchase ("Limited Warranty
period"), at its option either(a) repair your product with new or refurbished parts, or (b) replace
it with a new of a refurbished product. The decision to repair or replace will be made by the
warrantor. During the "Labor" Limited Warranty period there will be no charge for labor. During
the "Parts" warranty period, there will be no charge for parts. You must mail-in your product
during the warranty period. This Limited Warranty is extended only to the original purchaser and
only covers product purchased as new. A purchase receipt or other proof of original purchase
date is required for Limited Warranty service.
Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner of benzine to clean this unit.
Product Service
1) Damage Requiring Service:
The unit should be serviced by qualified service personnel if:
(a) The DC power supply cord or AC adaptor has been damaged;
(b) Objects or liquids have gotten into the unit;
(c) The unit has been exposed to rain;
(d) The unit does not operate normally or exhibits a marked change in performance;
(e) The unit has been dropped or the cabinet damaged.
2) Servicing Personnel: Do not attempt to service the unit beyond that described in
these operating instructions. Refer all other servicing to authorized servicing personnel.
3) Replacement Parts: When parts need replacing ensure the servicer uses parts
specified by the manufacturer or parts that have the same characteristics as the
original parts. Unauthorized substitutes may result in fire, electric shock, or other
hazards.
4) Safety Check: After repairs or service, ask the servicer to perform safety checks to confirm that
the unit is in proper working condition.

Extended Warranty
With the registration of supported J-Tech Digital products, you extend the current warranty
by 6 months. This extension is added to the warranty that starts at the purchase date of
the device supported. Total product warranty with the extended period will equate to a
total of 18 months of warranty from the date of purchase.
For extended warranties to be accepted, all warranty extensions must be claimed within
30 days of purchasing the eligible J-Tech Digital product. Extensions attempted to be
claimed outside of the 30-day window will not be accepted.
J-Tech Digital Support Team
[email protected]
(888) 610 – 2818