Jacuzzi J-STONE SS 4242 User manual

NEO-ANGLE
SINGLE THRESHOLD
PRODUCT CHART
J-STONE™
SHOWER BASES
WHIRLPOOL
BATH
R
B
A
C
D
A
A
D
D
B
C
B
D
21-3/16"
17-3/16"
17-3/16"
18-3/16"
12-3/16"
12-3/16"
C
21-3/16"
24-3/16"
30-3/16"
18-3/16"
25"
25-1/8"
B
42-3/16"
34-3/16"
34-3/16"
36-1/8"
18-3/16"
20-3/16"
A
42-3/8"
48-3/8"
60-3/8"
36-5/16"
36-1/8"
38-1/8"
MODEL
SS 4242
SS 3448
SS 3460
SS 3636
SS 36NEO
SS 38NEO
ROUGH-IN DIMENSION
PRODUCT
NO.
PO45
PO41
PO46
PO42
PO43
PO44
NOMINAL
SIZE
42" X 42"
34" X 48"
34" X 60"
36" X 36"
36" X 36"
38" X 38"
INSTALLATION
With the drain fitting passing over the center of the
drainpipe, lower the shower base carefully into place,
push down firmly until the base is in place.
Provideanopeninginthesubfloornolessthan5"x5"
square. See product chart for hole location. The
opening is to accommodate a 2" waste pipe.
If the subfloor is level, no other preparation is neces-
sary. Youcanproceedtoinstalltheshowerbase. Ifthe
subfloor is not level, you MUST level the entire surface
prior to installing the base. (Use a floor leveling com-
pound.) Do not level shower base with mortar. Both
sides of a joint or splice of subfloor should be level to
each other. Level and support waste pipe cutout area
greater than 5" x 5".

Printed in U.S.A.
© 1998 Jacuzzi Whirlpool Bath P063000 A 1/99
Printed on Recycled Paper
Jacuzzi Whirlpool Bath National Headquarters
P.O. Drawer J, Walnut Creek, CA 94596 [phone]
Service Support: Call [phone]
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of
thistype. Itistheresponsibilityoftheinstaller/ownertodeterminespecificlocalcodecompliancepriortoinstallationoftheproduct.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
GAP
BASE
INCORRECT
BLOCKING
SHIM
STUD
CORRECT
BLOCKING
BASE
FLANGE
STUD
If there is any gap between base flange and stud or
blocking, shims MUST be used to prevent distortion or
cracking of the flange.
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
fromtheback of thedrainassembly. Apply a 1/4"bead
of caulking (silicone) to the drain hole and insert the
drain assembly. Replace the rubber washer, fiber
washer, and lock nut in that order. Hand tighten the
locknut. Remove excess sealant from finished side.
Apply a lubricant (common household liquid soap
works well) to the inside of the rubber seal of the drain
assembly.
GROUT
STUD
SHIM IF NECESSARY
DO NOT FILL
BLOCKING
CEMENT
BOARD
TILE
SILICONE
SEALANT
TIGHTEN
SEALING
NUT
TOOL
(INCLUDED)
STRAINER
DRAIN
ASSEMBLY SILICONE
SEALANT
SHOWER
BASE
RUBBER
WASHER
FIBER
WASHER NUT
APPLY
LUBRICANT
With a large screwdriver and the tool included with the
drain,tightentheinsidecompressionnuttosealthedrain
pipe connection. After drain is fully installed, test for
proper drainage. If the shower base does not drain
properly,rectifythisconditionbeforeproceedingwiththe
installation. Jacuzzi Whirlpool Bath is not respon-
sible for removal and/or reinstallation costs.
HOWTOCAREFORYOURJ-STONESHOWERBASE
Never use abrasive or gritty powder cleaners, pads or
sharp instruments when cleaning the shower base. Al-
ways clean with mild household detergent. Persistent
stains, paint or tar should be removed with turpentine,
paint thinner or household glass cleaner.
Install cement board. Apply tile (or other finishing
material) leaving a 1/8" gap between the finishing mate-
rial and the shower base flange lip. Seal this gap with
siliconesealant. Leaveaminimum1/4"weepholeatthe
back and front corners of the shower base. The weep
holes are necessary to allow drainage from leakage
through unsealed tiled grout.
Filling the area marked DO NOT FILL will prevent
moisture from draining back into the base through the
weepholes. Thismoisture is duetoleakagethrough the
tile grout. Sealing the tile grout will prevent this leakage.