Jadak HS-1RL User manual

HS-1RL QUICK START GUIDE
HS-1RL-QSG
Rev A

HS-1RL Quick Start Guide 1
www.JADAKtech.com
Unpack the HS-1RL
Included Components
• HS-1RL with attached USB cable
• Quick Start Guide
NOTE: The attached USB cable is the only cable that should be used with the HS-1RL.
User Feedback
LED Indicators
Green = good read
Red = no read
Beeper
The default volume of the beeper is set to high. To adjust or disable the beeper volume, see the User
Guide on the HS-1RL support page at www.jadaktech.com.
Vibration (optional feature)
If your HS-1RL has the vibration feature, it vibrates for every good read. This feature is enabled by default.
See the User Guide to adjust or disable the vibration.
Connect the HS-1RL
HID Keyboard Mode
By default, the HS-1RL is configured to communicate in USB HID Keyboard mode. For Windows 10 and Linux
operating systems, no additional driver is required when using the device in the default mode. USB devices are
automatically detected after plugging in the device. If the automatic detection fails, or for Windows 7 operating
systems, follow these steps:
1. Download the driver from the HS-1RL support page at www.jadaktech.com. Extract the files to a chosen folder.
2. Turn off the power to the device/computer.
3. Plug the HS-1RL USB cable into your device/computer and then power up the device/computer.
4. Open Device Manager and find HS1RX in the device listing with a yellow exclamation mark in the lower left
corner. Right click and select Properties.
5. Select Update Driver.

HS-1RL Quick Start Guide 2
www.JADAKtech.com
6. Select Browse My Computer for Driver Software.
7. Select Let me pick from list of device drivers on my computer.
8. Scroll down the window and select Ports (COM & LPT).
9. Select Next, then Have Disk, then Browse.
10. Navigate to the previously chosen folder, where the driver .inf file is located. Select the JADAK driver .inf file.
Select Open, then OK.
11. Select HS1Rx, then select Next. Select Yes or Proceed to any warnings that may appear.
12. Windows should now display that the driver has been successfully updated.
USB COM Port Emulation Mode
To communicate with the HS-1RL using USB COM Port Emulation, scan the following code. This programs the HS-
1RL to emulate an RS-232-based COM port.
NOTE: Unplug the USB connector, then plug it back in to power cycle the unit after scanning this code.
Consult the User Guide to adjust other device settings.
Scan Barcodes and Read RFID Tags
The HS-1RL scans all popular 1D and 2D barcodes and a broad variety of Low Frequency (LF) RFID tags. For a full
list, see the product specification sheet and/or User Guide.
The HS-1RL cannot scan barcodes and read RFID tags simultaneously. If the unit is not triggered to read barcodes
(top trigger button is not pressed or not programmatically triggered), the unit is in RFID mode and is actively
scanning for RFID tags. Consult the User Guide to configure the device trigger mode and behaviors.
Scan the following code to revert the unit to its default settings. Hold down the trigger button until the LED flashes
green.
Clean the HS-1RL
Barcode reading performance may degrade if the scanner’s window is not clean. If the window is visibly dirty, or if
the scanner isn’t operating well, clean the window with a soft cloth or lens tissue dampened with water (or a mild
detergent and water solution). If a detergent solution is used, rinse with a clean lens tissue dampened with water
only.
The HS-1RL is IP54 rated when the cable is attached. This means that liquids and dust will not penetrate the
housing, however, the scanner should not be submerged in water or other liquids. It is also recommended to
dampen the cleansing cloth instead of spraying the scanner directly.
JADAK hand scanners are designed and manufactured to withstand the most popular cleaners used in the
healthcare market: Sani-Cloth® HB, Sani-Cloth® Plus, Hydrogen Peroxide, CaviWipes™, 409® Glass and Surface
Cleaner, Windex® Blue, Clorox® Bleach (100%), Isopropyl Alcohol, or gentle dish soap and water.
#HOSTCFG 0
#DEFAULT

HS-1RL Quick Start Guide 3
www.JADAKtech.com
Environmental Statements
Waste Electrical and Electronic Equipment (WEEE) Information
This product has required the extraction and use of natural resources for its production. It may contain hazardous
substances that could impact health and the environment, if not properly disposed. In order to avoid the
dissemination of those substances in our environment and to diminish the pressure on natural resources, we
encourage you to use the appropriate take-back systems for product disposal. JADAK is a participant in the WEEE
directive. For more information email us at [email protected].
Restriction of Hazardous Substances (RoHS) Information
JADAK products do not, to the best of our knowledge, contain substances in excess of the Maximum Concentration
Value (MCV) as outlined in the directive RoHS 2015/863/EU.
Compliance Notices
The product is designed to support the following regulatory and safety standards as a standalone unit.
Model Number: HS-1RL
FCC ID: QV5HS1RL
IC: 5407A-HS1RL
EU: CE
Federal Communication Commission (FCC) and Industrie Canada (IC) Compliance
This device complies with FCC Rules Part 15 and with Industry Canada license-exempt RSS standard(s).
Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference that may be received or that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
EU Declaration of Conformity
Hereby, Novanta Corporation declares that the HS-1RL Low Frequency 125 kHz/134.2 kHz RFID reader is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address: http://www.jadaktech.com/resources/compliance-user-agreements.