J&D MAnufacturing STORM WITH CONE User manual

NOTE: Read ALL instructions over carefully before attempting
to install the Storm with cone.
If you have any questions please call your local dealer or
J&D Manufacturing at: 1-800-998-2398.
Or visit our website at: www.jdmfg.com
STORM WITH CONE
55” Fiberglass Exhaust Fan
PARTS LEGEND
WARRANTY
J&D Mfg. warrants all products are free from defects in materials and workmanship under
normal use for the period of one year from date of purchase and our warranty does not
cover normal or regular wear and tear. J&D Mfg can repair or replace at our option, any
product or part of the product that is found to be defective. Our warranty applies to
materials only and does not include return freight, delivery, loss or damage to personal
property, cost of removal or installation, any incidental or consequential damages or labor.
This warranty does not apply to products which are misused, abused, altered, improperly
installed or subject to negligence. All warranties must be approved through our warranty
department. The original purchaser must present a copy of the invoice for the defective
product. One year is our standard warranty unless specified on our literature or in the
installation instructions/user manuals.
INSTALLATION HARDWARE IS NOT PROVIDED
IS198-09H
RECOMMENDED TOOLS FOR INSTALLATION AND ASSEMBLY
(NOT PROVIDED)
Measuring
Tape
Safety Glasses
INCLUDED ASSEMBLY HARDWARE - TO SCALE
Guard ShutterHousing
(8) Flat Washer
5/16”
1/2"
Socket
Socket Wrench
Drill
and Drill Bits
3/16”
3/8”
(8) 3/16” x 1/4"
Aluminium Rivet
(8) 3/16”ID x 1/2"OD
Aluminium Rivet
Rivet Gun
(8) Shutter Clips
(13) Phillips Truss Bolt
5/16”-18 x 1”
(13) Nylock Flange Nut
5/16”-18
Cone
Construct structurally sound 59¾” square finished opening.
59 ¾”
59 ¾”
FINISHED
OPENING
(Inside Dimensions)
N
O
TE: Read ALL instructions over carefully before attem
p
tin
g
to install the Storm with cone
5
5” Fiber
g
lass Exhaust Fa
n
Correct orientation of fan. From the inlet side, the motor will be located
above and to the right of the shaft.
Motor
View from inlet
side of fan
Phillips
Screwdriver

Using the measurements below and a 3/16” drill bit, drill a total of 8 holes
in the housing flange 1/2” from the flange edge.
1
Measure and mark the exterior of the venturi 2” from edge of opening as
shown in illustration. These will be your guides for properly installing the
cone in step 5.
3
Attach all (8) shutter clips with a rivet gun using (8) 3/16” rivets and (8)
3/16” washers. Review the illustrations below for placement and assembly.
2a
Fan
Flange
Shutter
Clip
Rivet
Washer 2b
Rivet
Washer
Fan
Flange
Shutter
Clip
2
155
/
8
” 155
/
8
”
155
/
8
” 155
/
8
”
155
/
8
” 155
/
8
”
187
/
8
” 187
/
8
”
edge of venturi
2”

Slide cone onto venturi so that venturi and cone overlap by approximately
2”. Use marks made in step 3 as your guide.
5
Insert guard into cone. Using the predrilled holes in the end of the cone,
secure the guard to the cone using (8) 5/16” Hex Bolts, (8) 5/16” Flat
Washers, and (8) 5/16” Nylock Flange Nuts. Review the Assembly Side
View illustration for proper installation. Do not tighten until all have been
assembled.
7
From the inside of your structure, rotate the fan housing until the motor is
located above and to the right of the shaft, as shown in the illustration on
the front page. Insert fan housing into the finished opening and secure all 4
sides to structure using suitable fasteners and washers (not included).
4
Interior
of structure
Exterior
of structure
Using the 5 predrilled holes in the cone, drill matching holes in venturi and
secure with (5) 5/16” Phillips Truss Bolts and (5) 5/16” Nylock Nuts. Insert
bolt from the interior of the cone and secure with nut on exterior.
6
Assembly Side View
Connecting power to the unit.
• Install manual disconnect switch inside
building adjacent to fan.
• Route wire to motor with drip loop and
secure. Drip loop will drain accumulated
moisture away from the motor.
• Configure internal wires to match supply
voltage and wire according to motor
nameplate. Test to verify correct rotation.
• Shut off manual disconnect for remainder
of install. Only permit power to unit when
shutter and guard is fully installed to
prevent injury.
8
ALL ELECTRICAL WORK SHOULD BE
COMPLETED BY QUALIFIED PERSONNEL AND
MEET NATIONAL, REGIONAL AND LOCAL CODES
Nut
Cone
Guard
Mounting
Foot
Washer
Bolt

10
Tour our website for
new
innovative
quality
J&D and Pruden ventilation products.
www.jdmfg.com
Swivel top and side shutter clips open. Set bottom shutter flange into
bottom shutter clips. Secure shutter by swiveling top and side shutter clips
over shutter flange.
9