janitza UMG 96 RM Instruction manual

Doc. no. 1.040.015.4b
Power Analyser
UMG 96 RM
Basic device
Operating instructions and
technical data
Item no. 33.03.114
Janitza electronics GmbH
Vor dem Polstück 1
D-35633 Lahnau
Support tel. [phone]
Fax [phone]
E-mail: [email protected]
Internet: http://www.janitza.com
www.janitza.com
from firmware 1.1.x
Power Analyser

2
UMG 96RM
Commissioning 54
Applying the supply voltage 54
Applying the measured voltage 54
Applying the measured current 54
Rotation field direction 55
Checking the phase assignment 55
Checking the power measurement 55
Checking the measurement 55
Checking the individual power ratings 55
Check the sum power ratings 56
RS485 interface 57
Digital outputs 59
Pulse output 61
Comparator 67
Service and maintenance 70
Error messages 71
Technical data 78
Parameters of functions 82
Table 1 - Parameter list 84
Table 2 - Modbus address list 90
Dimensional drawings 94
Overview of measured value displays 96
Declaration of conformity 102
Connection example 103
Brief instructions 104
Inhaltsverzeichnis
General 4
Incoming goods inspection 6
Scope of delivery of the basic device 7
Available accessories 7
Product description 8
Intended use 8
Characteristics of the basic device 9
Measuring method 10
GridVis network analysis software 11
Connection options 11
Assembly 12
Installation 14
Supply voltage 14
Voltage metering 16
Current measurement 22
RS485 interface 29
Digital outputs 32
Operation 34
Display mode 34
Programming mode 34
Parameters and measured values 36
Configuration 38
Applying the supply voltage 38
Current and voltage transformers 38
Programming current transformers 40
Programming voltage transformers 41
Programming parameters 42

3
UMG 96RM

4
UMG 96RM
Comments about the manual
Your comments are welcome. If anything in this manual
is unclear, please let us know and send us an e-mail at:
[email protected]
General
Copyright
This manual is subject to the laws of copyright
protection and may not be mechanically or electronically
photocopied, reprinted, reproduced or otherwise
reproduced or published in part or as a whole, without
the legally binding, written consent of
Janitza electronics GmbH, Vor dem Polstück 1,
D 35633 Lahnau, Germany.
Trademarks
All trademarks and the rights resulting from them remain
the property of the trademark holder of these rights.
Disclaimer
Janitza electronics GmbH assumes no responsibility
for errors or omissions in this manual and assumes no
obligation to keep the contents of this manual up to date.
Meaning of the symbols
The following pictograms are used in this manual:
cDangerous voltage!
Risk of death or serious injury. Disconnect
the power before working on the system
and device.
mAttention!
Please refer to the documentation. This
symbol will warn you of possible dangers
that could occur during assembly,
commissioning and operation.
CNote!

5
UMG 96RM
Application notes
Please read these operating instructions and all other
publications that must be consulted in order to work
with this product (particularly for installation, operation
or maintenance).
Please observe all safety regulations and warnings. Non-
compliance with the instructions can lead to personal
injury and/or damage to the product.
Any unauthorised alteration or use of this device which
exceeds the specified mechanical, electrical or other
operational limits can cause personal injury and/or
damage to the product.
Any such unauthorised alterations are grounds
for "abuse" and/or "negligence" in terms of the product's
guarantee and thus excludes the warranty for covering
any possible resulting damages.
This device must only be operated and maintained
by qualified personnel.
Qualified personnel are persons who, due to their
respective training and experience, are able to recognise
risks and avoid potential hazards that can be caused
by operation or maintenance of the device.
When using the device, the legal and safety regulations
required for the respective application must also be
observed.
cSafety is no longer guaranteed and the
device may be dangerous if the device is
not operated according to the operating
instructions.
mConductors consisting of single wires must
be provided with ferrules.
mOnly screw terminals with the same
number of poles and the same type may
be plugged together.

6
UMG 96RM
Incoming goods inspection
The proper and safe operation of this device
requires appropriate transport, proper storage,
installation and assembly as well as careful operation
and aintenance. When it is assumed that safe operation
is no longer possible, the device must immediately be
taken out of operation and secured against accidental
start-up.
Unpacking and packing must be carried out with
the usual care, without the use of force and only with
the use of suitable tools. The devices must be visually
inspected for proper mechanical condition.
It can be assumed that safe operation is no longer
possible if the device, e.g.
• shows visible damage,
• does not work despite intact power supply,
• and was exposed to unfavourable conditions
(e.g. storage outside of the permissible climatic
limits without adaptation to the ambient climate,
condensation, etc.) or transport stresses (e.g. falling
from a great height even without exterior visible
damage, etc.) for prolonged periods.
• Please check that the delivery is complete before you
begin with installation of the device.
CAll supplied screw terminals are
attached to the device.
About these operating instructions
These operating instructions are part of the product.
• Read the operating instructions prior to using
the device.
• Keep the operating instructions at hand throughout
the entire service life of the product and keep ready
for referencing.
• Hand over the operating instructions to each
subsequent owner or user of the product.

7
UMG 96RM
Scope of delivery of the basic device
Quantity Item no. Designation
1 52.22.001 UMG 96RM
2 29.01.036 Mounting brackets.
1 33.03.113 Operating instructions.
1 51.00.116 CD with the following contents.
- GridVis programming software
- GridVis functional description
1 10.01.818 Screw terminal, pluggable, 2-pin (auxiliary energy)
1 10.01.828 Screw terminal, pluggable, 4-pin (voltage measurement)
1 10.01.820 Screw terminal, pluggable, 6-pin (current measurement)
1 10.01.807 Screw terminal, pluggable, 2-pin (RS 485)
1 10.01.808 Screw terminal, pluggable, 3-pin (digital/pulse output)
Available accessories
Item no. Designation
29.01.907 Seal, 96 x 96
18.08.094 RS485, external terminating resistor, 120 ohm
15.06.015 Interface converter RS485 <-> RS232
15.06.025 Interface converter RS485 <-> USB

8
UMG 96RM
Product description
Intended use
The UMG 96RM is provided for the measurement
and calculation of electrical parameters such as voltage,
current, power, energy, harmonics, etc. for building
installations, to distributors, circuit breakers and busbar
trunking systems.
The UMG 96RM is suitable for installation in permanent,
weatherproof switchboards. Conducting switchboards
must be earthed. It can be mounted in any position.
Measurement voltages and measurement currents must
originate from the same grid.
The measurement results can be displayed and can
be read and processed over the RS485 interface.
The voltage measurement inputs are designed
for measuring in low voltage grids in which nominal
voltages up to 300V phase can occur in countercurrent
with ground and overvoltages of overvoltage category
III.
The UMG 96RM current measurement inputs are
connected via external ../1A or ../5A current transformers.
Measurements in medium and high voltage systems
generally use current and voltage transformers.
The UMG 96RM can be used in residential and industrial
areas.
Device characteristics
• Installation depth: 45 mm
• Supply voltage: 230 V (95 V-240 V AC)
• Frequency range: 45-65 Hz
Device functions
• 3 voltage measurements, 300 V
• 3 current measurements (via current transformer)
• RS485 interface
• 2 digital outputs

9
UMG 96RM
Characteristics of the basic device
• General
• Front panel-mounted with the dimensions
96x96 mm.
• Connection via screw-type terminals.
• LC display with backlighting.
• Operation via 2 buttons.
• 3 voltage measurements inputs (300V CATIII).
• 3 current measurement inputs for current
transformer.
• RS485 interface (Modbus RTU, slave,
to 115 kbps).
• 2 digital outputs.
• Working temperature range -10°C .. +55°C.
• Storage of minimum and maximum values
(without time stamp).
• Measurement uncertainty
• Active energy, measuring uncertainty class
0.5 for ../5 A transformer.
• Active energy, measuring uncertainty class
1 for ../1 A transformer.
• Reactive energy, class 2.
• Measurement
• Measurement in IT and TN networks.
• Measurement in networks with nominal voltages
up to L-L 480 V and L-N 277 V.
• Current metering range 0 .. 5 Aeff.
• True root mean square measurement (TRMS).
• Continuous scanning of voltage
and current measurement inputs.
• Frequency range of the mains frequency
45 Hz .. 65 Hz.
• Measurement of harmonics 1 to 40
for ULN and I.
• Uln, I, P (import/delivery), Q (ind./cap.).
• Recording of more than 800 measured values.
• Fourier analyses 1 to 40.
Harmonic for U and I.
• 7 power meter for
Active energy (import)
Active energy (export)
Active energy (without a backstop)
Reactive energy (ind.)
Reactive energy (capacitive)
Reactive energy (without a backstop)
Apparent energy
each for L1, L2, L3 and total.
• 8 tariffs (switching via Modbus).

10
UMG 96RM
Measuring method
The UMG 96RM measures uninterrupted and calculates
all root mean squares over a 9-period interval. The UMG
96RM measures the true root mean square (TRMS)
of the voltages and currents applied to the measuring
inputs.
Operating concept
There are several ways to program the UMG 96RM
and retrieve measured values.
• Directly on the device using two buttons.
• Via the programming software of the GridVis.
• Via the RS485 interface with the Modbus protocol.
Data can be changed and retrieved with the help of the
Modbus address list (stored on the accompanying
data carrier).
These operating instructions only describe the operation
of the UMG 96RM using the 2 buttons.
The programming software of the GridVis has its own
"online help".