Jason.L Blackjack User manual

ASSEMBLY INSTRUCTIONS
Blackjack Boardroom Table
Indented Chrome Legs
Page 1 of 5
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Tools Required: Power screwdriver.
2 persons required for installation
Special Note: No pre-drilled holes or nut inserts are
provided. Wood screws will be required to be drilled
directly into underside of desk top.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
COMPONENTS
SCREWS
Page 2 of 5
Upper Wrist x2
Top Rail Ø45 x1
Leg-pole Tube Ø51 x2
Large Foot x4
Foot Glide x4
Top Rail Cap x2
150° Collar x2
Table Top x1
150° Gasket x2
Plastic Support x1
M10x30mm x2
M10x110mm x2
M8x16mm x4
M5x25mm Self Tapping
7
6
2
5
11
4
14
3
10
12
13
1
8
9
ASSEMBLY INSTRUCTIONS
Blackjack Boardroom Table
Indented Chrome Legs
Need help!
Call us on
1300 527 665
www.jasonl.com.au

Slide 2 large feet (4) into the collar, place the 150° gasket (9) on top and fully
tighten the 2 M8x16mm bolts (13) into the collar (7) . (Repeat with all collars).
Place a leg pole tube (3) on top of a collar. Align the notch. Fully tighten the
M10x110 bolt (12), spring washer and flat washer through the collars. Repeat
for both leg assemblies.
Place the upper wrist (1) on top of the leg tube, making sure each small
notch in the top of the leg tube is in-line with the bumps on the bottom of
the upper wrist. Fully tighten to maximum tension the M10x30mm bolts (11).
Repeat for both leg assemblies.
Screw all glides (5) into the base of the large feet, leaving the glides one turn
from tight (then they can be adjusted easily if the floor is uneven).
Page 3 of 5
12 11
1
3
13
9
45
7
ASSEMBLY INSTRUCTIONS
Blackjack Boardroom Table
Indented Chrome Legs
Need help!
Call us on
1300 527 665
www.jasonl.com.au
01 02
03 04
* The top of the leg tube has
more rim notches than the
bottom of the leg tube.

With the legs assembled, place each end of the top rail (2) into the holes
on the side of the upper wrist, making sure they stop before going all the
way through. (It is permissible in some applications for top rail to
protrude out further past the wrists.)
Place the top rail cap (6) into the exposed side end of the top rail. Locate the plastic support bracket (10) over the
centre of the top rail, and click into place.
Fully tighten the small screws located at the bottom of each upper
wrist to firmly hold the top rail in place.
Page 4 of 5
ASSEMBLY INSTRUCTIONS
Blackjack Boardroom Table
Indented Chrome Legs
Need help!
Call us on
1300 527 665
www.jasonl.com.au
2
610
05 06
07 08

08
14
Optional: For extra strength, the plastic support bracket can be screwed
onto the top rails.
With the frame assembly complete, locate it in the centre of the work
surface and screw the remaining self tapping screws (14) into each
upper wrist and plastic support.
Page 5 of 5
ASSEMBLY INSTRUCTIONS
Blackjack Boardroom Table
Indented Chrome Legs
Need help!
Call us on
1300 527 665
www.jasonl.com.au
09 10