Jason.L ST SUPREME E23T User manual

ASSEMBLY INSTRUCTION
MODEL : ST SUPREME E23T
Electric Height Adjustable Table Frame
(4 to 6 Feet Length)

Component List - ST SUPREME E23T
03
10
11
18
17
19
13
08
15
01 02
16
04
05
07 12
09
06
AR
20
14
Axle Drive L390mm
ET-00-309
Qty : 2
Hex Shalf L295mm
ET-00-303
Qty : 2
Hex Shalf L430mm
ET-00-307
Qty : 1
Screw M5 X L10
Qty : 14
Left Column
FA-20-106-L-01
Qty:1
Crossbar Motor Model
CB-10-219-00
Qty : 1
Cable Tray
FA-00-220B-00
Qty : 1
Right Column
FA-20-106-ER-01
Qty: 1
Foot
FA-10-315-02
Qty: 2
Crossbar Assy. Left
CB-10-217B-01
Qty: 1
Screw M6XL10
Qty : 3
Leveling Base
Qty: 4
Control Box
TC2B
Qty : 1
Motor
TGM1-2252-002
Qty : 1
Handset TH14
Qty : 1
Rubber Pad Type-T
Qty: 10
Crossbar Assy. Right
CB-10-217A-01
Qty: 1
Axle Drive L550mm
ET-00-306
Qty : 2
Side L Plate
FA-00-119-01
Qty: 2
Screw M6 X L16
Qty : 8

Pg.1/11
04
03
17
17
01
15
15 15
15
Marking 'L' column
direction must be follow
13
13
13
13
STEP 2 : Install Foot
STEP 3 : Install Crossbar Left Assy.
Step 1 : Install Leveling Base
ITEM NO. DESCRIPTION QTY.
03 Foot FA-10-315-02 1
17 Leveling Base 2
ITEM NO. DESCRIPTION QTY.
01 Left Column FA-20-106-L-01 1
15 Screw M6 XL16 4
ITEM NO. DESCRIPTION QTY.
04 Crossbar Assy. Left CB-10-217B-01 1
13 Screw M5 XL10 4
Assembly Instruction: Left Stand Assembly

Pg.2/11
03
17
17
02
15
15 15
15
13
13
13
13
Marking 'R' column
direction must be follow
STEP 2 : Install Foot
STEP 3 : Install Crossbar Right Assy.
Step 1 : Install Leveling Base
ITEM NO. DESCRIPTION QTY.
03 Foot FA-10-315-02 1
17 Leveling Base 2
ITEM NO. DESCRIPTION QTY.
02 Right Column FA-20-106-ER-01 1
15 Screw M6 XL16 4
ITEM NO. DESCRIPTION QTY.
05 Crossbar Assy. Right CB-10-217A-01 1
13 Screw M5 XL10 4
Assembly Instruction: Right Stand Assembly

07
Set Screw M6
(X4)
Pg.3/11
Notes :
1.Please follow arrow left and right direction to
adjust the frame length fixed table top size.
2.Tighten set screw M6(X4) after fixed frame length.
(Recommanded length 115cm,145cm,175cm)
ITEM NO. DESCRIPTION QTY.
07 Crossbar Motor Model CB-10-219 -00 1
Assembly Instruction: Integrate Left & Right Stand

18
14
14
14
Pg.4/11
ITEM NO. DESCRIPTION QTY.
18 Motor TGM1-2252-002 1
14 Screw M6 XL10 3
Assembly Instruction: Install Motor Assembly

For Length 115cm to 145cm
10
10
11
PRESS DOWN
PRESS DOWN
8
8
Set Screw
M5(X8)
Notes:
1.Before Insert Hex Shaft, make sure
Left Stand & Right Stand are at lowest position.
Please see attachment caution ! (Refer Pg7/11).
2.Tighten set screw M6(X4) after fixed frame length
Pg.5/11
ITEM NO. DESCRIPTION QTY.
08 Axle Drive L390mm ET-00-309 2
10 Hex Shaft L295mm ET-00-303 2
11 Hex Shaft L430mm ET-00-307 1
Assembly Instruction: Axle Drive And Hex Shaft Assy.

For Length 145cm to 175cm
09
09
10
10
11
PRESS DOWN
PRESS DOWN
Set Screw
M5(X8)
Notes:
1.Before Insert Hex Shaft, make sure
Left Stand & Right Stand are at lowest position.
Please see attachment caution ! (Refer Pg.7/11)
2.Tighten set screw M6(X4) after fixed frame length
Pg.6/11
ITEM NO. DESCRIPTION QTY.
8 Axle Drive L550mm ET-00-306 2
10 Hex Shaft L295mm ET-00-303 2
11 Hex Shaft L430mm ET-00-307 1
Assembly Instruction: Axle Drive And Hex Shaft Assy.

AW
BC
BR
16
BN
16
BP
Press down the column make sure it is at lowest postion.
The marking O not appear means it is at lowest position
refer to below diagram.
Marking
fully seen
Marking
partially seen
Marking not seen
(Means at lowest position)
Press
Press
Pg.7/11
Caution: Column Must Be At Lowest Position Before Install Hex Shaft

06
06
13
13
13
13
Pg.8/11
ITEM NO. DESCRIPTION QTY.
06 Side L Plate FA-00-119-01 2
13 Screw M5 XL10 4
Assembly Instruction: Install Side L Plate

13
Install Control Box & Handset
Install Cable Tray
12
13
19
20
Notes :
Step 1: Install Cable Tray
Step 2: Lock with screw M5
Notes :
Step 1: Place Control Box to Cable Tray
Step 2: Plug Motor connector and Handset
connector to control box
Pg.9/11
ITEM NO. DESCRIPTION QTY.
12 Cable Tray FA-00-220B-00 1
13
Screw M5 XL10 2
ITEM NO. DESCRIPTION QTY.
19 Control Box TC2B 1
20 Handset TH14 1
Assembly Instruction: Install Cable Tray & Control Box & Handset

16
16
16 16
16
16
16
16
16
16
CG
Plug Rubber Pad Type-T
CG
Pg.10/11
Before
V1.0
After
ITEM NO. DESCRIPTION QTY.
16 Rubber Pad Type-T 10
Assembly Instruction: Plug Rubber Pad Type-T

'DOWN BUTTON' 'UP BUTTON'
Pg.11/11
Reset operation as below :
1.One time reset
The first powered up, press and hold 'Down Button', the desk moving down
to lowest position.
After checking the signal motor constant, reset was completed and ready to
use.
2. Any dismantle of electrical component follow below procedure.
Press both button up and down for 3-5 seconds to clear memory.
Follow procedure no.1 again.
Assembly Instruction: Reset The Desk Before Use