F
4x4
2
1
E
3
4
B
E3
4
D
AC
HS M1 M2
7
DC
B
B
D
6
8
6
7
2
3
1
B
D
F
STEP 4
STEP 5
STEP 6
Install tabletop and handset
Attention: When the extension of
supporting beam is larger than
1720mm, the installation method
is as follows: Method 2 in Step 6.
The extension distance of the
supporting beam can be adjusted
according to the actual use.
Loosen
Adjust
Tighten
Fix the tabletop on the frame with screws (E) and use
screws (8) to fix handset (6).
Connect all cables to the control box
Port for
handset
Port for
power plug
Ports for
lifting columns
Install the cable
management tray
Method 1
STEP 1: Tighten the screws incompletely
STEP 2: Buckle the tray
Tighten
Buckle from
one side
Buckle the
other side
Firstly, rotate the screws (B) incompletely into the supporting
beam (4) with allen key (F). Next, slide one side of the cable
management tray (3) into the screws (B), then the other side.
Finally, tighten the screws (B) with allen key (F).
Method 2
Install the cable management tray (3) as Method 1, Step 6.
When the supporting beam (3) stretches over 1720mm,
the cable management tray needs to be mounted on
the middle of the supporting beam. STEP 1: Tighten the
screws (B). And screw the
screws (D) incompletely.
The supporting beam should
not exceed this hole.
Method
The desktop could not function
Rising in a low speed
The desk moving downwards
without any operation
Automatically Self-Reset
The following tips will help you detected and eliminate the common fault and
error. If the fault you met is not listed below, please contact with your supplier.
Only the manufacturer and professionals are capable for investigating and
correcting those fault and error.
Fault phenomenon
Go down but not go up or go up
but not go down
The upper and downward
height is not enough
The desk could not lifted
Overwork
(Duty cycle: Max 2min on/18min OFF)
Check if all the cables well
connected;
Check if overloaded,
max loading: 125kg;
Reset;
Restart after suspend for 18mins while
connecting with power.
Attention
1. Power supply: AC100V-240V, 50/60Hz
2. Service Environment: 0-40
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around. Always be careful to treat the packaging materials in order
to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
Ex12
Bx4
F
4x4
Bx4
F
4x4
Dx4
