JBL GTO Series 601.1 User manual

GTO Series
601.1
1 CHANNEL POWER AMPLIFIER
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 4/2004

- CONTENTS -
SPECIFICATIONS ………………………………….……..1
FEATURES/TEST CONDITIONS……..…………………2
INSTALLATION………………….……...……..…...…...…3
CONNECTIONS………………….……...……..…...…..…4
SET-UP/CONTROLS ……..………………..…….….…...5
INSTALLING NEON TUBES..…….…….………………..5
BASIC TROUBLESHOOTING..…….…….………………6
TYPICAL SYSTEM WIRING..…….…….……………..…7
EXPLODED VIEW/PARTS LIST…….….….…………....8
MECHANICAL PARTS LIST..…….…….……………......9
AMPLIFIER BLOCK DIAGRAM…………………….……10
P.C.B. DRAWINGS….……………………………….…….11
ELECTRICAL PARTS LIST ..……….……….…….….…14
IC/TRANSISTOR PINOUTS..……..….…….….….….…..18
SCHEMATICS………..……………………….…………...24
PACKING……..…………………………………………....27
GTO 601.1 Specifications
Output Power: 424W RMS x 1 channels @ 4 ohms; ≤1% THD + N
(14.4V supply) 580W RMS x 1 channels @ 2 ohms; ≤1% THD + N
Signal-to-noise ratio: 72dBA (reference 1W into 4 ohms)
Dynamic power: 778W @ 2 ohms
Effective damping factor: 6.32 @ 4 ohms
Frequency response: 10Hz – 302Hz (–3dB)
Maximum input signal: 5.3V
Maximum sensitivity: 210mV
DC Offset <50mV (-50%)
Output regulation: .21dB @ 4 ohms
Idle Current 1.3A
Input Impedance 22kΩ
Max Current Draw 39A @ 4 ohms
67A @ 2 ohms
Dimensions: 15 1/8 x 12 5/16 x 2 3/8” (L x W x D)
(384mm x 313mm x 60mm)
Fuses: 30A x 2
JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in
this and related JBL publications are therefore subject to change without notice.
1

2

INSTALLATION
2
WARNING: Playing loud music in an
automobile can hinder your ability to hear
traffic and permanently damage your
hearing. We recommend listening at low or
moderate levels while driving your car. JBL
accepts no liability for hearing loss, bodily
injury or property damage resulting from
the use or misuse of this product.
IMPORTANT: To get the best
performance from your JBL Grand Touring®
Series amplifiers, we strongly recommend
that installation be entrusted to a qualified
professional. Although these instructions
explain how to install GTO amplifiers in a
general sense, they do not show specific
installation methods that may be required
for your particular vehicle. If you do not
have the necessary tools or experience,
do not attempt the installation yourself.
Instead, please ask your authorized JBL
car audio dealer about professional
installation.
INSTALLATION
WARNINGS AND TIPS
•Always wear protective eyewear when
using tools.
•Turn off the audio system and other
electrical devices before you start.
Disconnect the (–) negative lead from
your vehicle’s battery.
•Check clearances on both sides of
a planned mounting surface before
drilling any holes or installing any
screws. Remember that the screws
can extend behind the surface.
•At the installation sites, locate and
make a note of all fuel lines, hydraulic
brake lines, vacuum lines and electrical
wiring. Use extreme caution when cut-
ting or drilling in and around these areas.
•Before drilling or cutting holes, use a
utility knife to remove unwanted fabric
or vinyl to keep material from snagging
in a drill bit.
•When routing cables, keep input-signal
cables away from power cables and
speaker wires.
•When making connections, make
certain they are secure and properly
insulated.
•If the amplifier’s fuse must be replaced,
use only the same type and rating as
that of the original. Do not substitute
another kind.
CHOOSING A LOCATION
AND MOUNTING THE
AMPLIFIER
Choose a mounting location in the trunk
or cargo area where the amplifier will not
be damaged by shifting cargo. Amplifier
cooling is essential for proper amplifier
operation. If the amplifier is to be installed
in an enclosed space, make sure there is
sufficient air circulation for the amplifier
to cool itself.
When mounting the amplifier under a
seat, ensure that it is clear of all moving
seat parts and does not affect the seat
adjustments. Mount the amplifier so it
is not damaged by the feet of backseat
passengers. Make sure that the amplifier
is mounted securely using nuts and bolts
or the supplied mounting screws.
Mount the amplifier so that it remains
dry – never mount an amplifier outside
the vehicle or in the engine compartment.
POWER CONNECTIONS
The GTO amplifiers are capable of
delivering extremely high power levels,
and require a heavy-duty and reliable
connection to the vehicle’s electrical system
in order to perform optimally. See Figure 1
for connection location. Please adhere to
the following instructions carefully:
Ground Connection
Connect the amplifier’s Ground (GND)
terminal to a solid point on the vehicle’s
metal chassis, as close to the amplifier
as possible. Refer to the chart below to
determine minimum wire-gauge size. Scrape
away any paint from this location; use a star-
type lock washer to secure the connection.
Power Connection
Connect a wire (see chart at right for
appropriate gauge) directly to the vehicle’s
positive battery terminal, and install an
appropriate fuse holder within 18" of the
battery terminal. Do not install the fuse at
this time. Route the wire to the amplifier’s
location, and connect it to the amplifier’s
Positive (+12V) terminal. Be sure to use
appropriate grommets whenever routing
wires through the firewall or other sheet
metal. Failure to adequately protect the
positive wire from potential damage may
result in a vehicle fire. When you are done
routing and connecting this wire, you may
install the fuse at the battery.
Remote Connection
Connect the amplifier’s Remote (REM)
terminal to the source unit’s Remote Turn-
On lead using a minimum of 18-gauge wire.
NOTE: When using the speaker level
inputs, connect the remote (REM) terminal
to the source unit. If your source unit does
not have a remote turn-on connection,
connect the amplifier’s (REM) terminal to
the vehicle’s accessory circuit.
Speaker Connections
Refer to the application guides on the
pages that follow. Speaker connections
should be made using a minimum of
16-gauge wire.
High-Level Input Connections
The GTO75.2, GTO75.4 and GTO755.6
amplifiers are equipped with speaker-level
inputs that allow you to add an amplifier
to head units that do not have RCA line
outputs. The speaker outputs for the
source unit should be connected to the
amplifier using the supplied connector
(square four-wire plug). Remember to
check for proper polarity. The GTO301.1,
GTO601.1 and GTO1201.1 amplifiers are
not equipped with high-level inputs.
NOTE: When using the high-level inputs,
the AUX outputs can be used to pass a
line-level signal to another amplifier.
Wire Gauge Chart
Amplifier Maximum Minimum
Model Current Draw Wire Gauge
GTO75.2 34A #8 AWG
GTO75.4 85A #8 AWG
GTO755.6 87A #8 AWG
GTO301.1 40A #8 AWG
GTO601.1 69A #6 AWG
GTO1201.1 115A #4 AWG
These recommendations assume 7' – 10'
wire runs. If your installation differs mark-
edly, you will need to adjust the wire
gauge accordingly.
IMPORTANT NOTE: If you are planning
to use optional neon tubes, install them
before making any electrical connections
to the amplifier (refer to“Installing Neon
Tubes” on page 6).
Figure 1. Terminal connection end plate.
GTO Amp OM 2/3/04 3:54 PM Page 2
3

CONNECTIONS – GTO301.1, GTO601.1 AND GTO1201.1
The GTO subwoofer amplifiers are
single-channel amplifiers. There are
two sets of terminals to make it easy
to connect multiple woofers. Either
set of (+/–) terminals may be used
when connecting woofers.
To the right are two application
diagrams to help plan your subwoofer
system installation. Figures 2 and 3
show how to configure the GTO
subwoofer amplifiers (models
GTO301.1, GTO601.1 and GTO1201.1).
NOTE: For simplicity, Figures 2 and 3
do not show power, remote and input
connections.
NOTE: Minimum speaker load is
2 ohms.
3
GTO Amplifier
(partial end panel)
Subwoofer
–
+
GTO Amplifier
(partial end panel)
Subwoofer Subwoofer
+
–
–
+
Figure 2. GTO subwoofer amplifier with two woofer connections. Figure 3. GTO subwoofer amplifier with one woofer connection.
GTO Amp OM 2/3/04 3:54 PM Page 3
4

6
INSTALLATION AND SETUP
SETTING THE
CROSSOVER(S)
Determine your system plans and set the
crossover mode switch accordingly. If you
plan to use the GTO75.2 or GTO75.4 to drive
full-range speakers, set the crossover
mode to FLAT and skip to “Setting Input
Sensitivity.”
Initially set the crossover frequency
control midway. While listening to music,
adjust the crossover for the least
perceived distortion from the speakers,
allowing them to reproduce as much
bass as possible.
Systems using a separate subwoofer set
the crossover mode to HP (high pass) for
your full-range speakers. Adjust the
crossover frequency to limit bass and
provide increased system volume with
less distortion.
For subwoofers, choose the highest
frequency that removes vocal information
from the sound of the subwoofer.
If using the GTO75.2 or GTO75.4 to drive a
subwoofer(s), set the crossover mode to
LP (low pass).
NOTE: The GTO301.1, GTO601.1, GTO1201.1
and the subwoofer output of the GTO755.6
are low-pass only and do not have a
crossover mode switch.
SETTING INPUT
SENSITIVITY
1. Initially turn the INPUT LEVEL control(s)
to minimum (counter clockwise).
2. Reconnect the (–) negative lead to the
vehicle’s battery. Apply power to the
audio system and play a dynamic music
track.
3. On the source unit, increase the volume
control to 3/4 volume. Slowly increase
the INPUT LEVEL control(s) toward three
o’clock until you hear slight distortion
in the music. Then reduce the INPUT
LEVEL slightly until distortion is no
longer heard.
NOTE: After the source unit is on, red LEDs
(on the top panel) will light, indicating the
amplifier is on. If not, check the wiring,
especially the remote connection from the
source unit. Also refer to “Troubleshooting”
on the next page.
REMOTE LEVEL CONTROL
The GTO755.6 and all three GTO subwoofer
amplifiers have inputs for an optional
remote level control (RLC). This will allow
the amplifier’s input level to be adjusted
from the listening position. Connect the
optional remote level control using the
RJ-11 jack on the side of the amplifier.
Install the control module in the front of
the vehicle within easy reach of the driver.
Under the dash or in the center console
are both suitable locations.
SETTING THE BASS BOOST
The GTO755.6, GTO301.1, GTO601.1 and
GTO1201.1 are all equipped with a bass-
boost control. This allows you to adjust the
bass output of your system at 50Hz up to
12dB and enhance low frequency.
AUX OUTPUT
GTO amplifiers (except GTO755.6) are
equipped with full-range outputs that can
be used to connect additional amplifiers.
NOTE: When using the high-level inputs,
the AUX outputs can be used to pass a
line-level signal to another amplifier.
INSTALLING NEON TUBES
(OPTIONAL)
1. Using a Phillips screwdriver, remove all
screws on the amplifier’s output/power
end panel and set them aside.
2. Using a 3⁄32-inch Allen wrench, remove
only the screws on the amplifier’s (top)
clear cover and set them aside.
3. Remove the end panel and slide the
cover off. Set both parts aside.
4. Locate the enclosed hardware bag and
remove the four clips. Each clip has a
square end and a larger round end.
Using a round end, press two clips onto
each neon tube (e.g., Street Glow AN9
or equivalent), as shown in Figure 13.
5. For each tube, align both clips so the
square ends slide onto an exposed
extrusion edge, as shown in Figure 9.
Do not cover any screw holes. When
installed correctly, each neon tube will
sit under an extrusion and not be visible
when viewed from directly above.
6. Route each neon tube’s power cable
through its respective NEON hole on the
end panel (see Figure 13).
7. Slide the cover back into place and re-
install its screws. Then, replace the end
panel and reinstall its screws.
8. Finish the installation of the neon tubes
as instructed in their owner’s manual.
Figure 12. Control end panel.
GTO75.2
GTO75.4
GTOB300.1/600.1/1200.1
GTO75.6
GTO Amp OM 2/3/04 3:54 PM Page 6
5

7
INSTALLATION AND SETUP
To Neon
Power
Supply
To Neon
Power
Supply
Figure 13. Installing neon tubes in a JBL GTO amplifier.
TROUBLESHOOTING
SYMPTOM LIKELY CAUSE SOLUTION
No audio No voltage at BATT+ Check voltages at
(POWER LED or REM terminals, amplifier terminals
is off) or bad or no ground with VOM
connection
No audio DC voltage on Amplifier may need
(PROTECT LED amplifier output service; see enclosed
flashes every warranty card for
4 seconds) service information
No audio Amplifier is Make sure amplifier
(PROTECT overheated cooling is not blocked
LED is on) at mounting location;
verify speaker system
impedance is within
specified limits (see
“Specifications” on
the next page)
No audio Voltage less than 9V on Check vehicle
(PROTECT BATT+ connection charging system for
and POWER defective voltage
LEDs flash) regulator
SYMPTOM LIKELY CAUSE SOLUTION
No audio Voltage more than 16V Check vehicle
(PROTECT or less than 8.5V on charging system for
LED is on) BATT+ connection defective voltage
regulator
Distorted audio Input sensitivity is Check INPUT
not set properly, or LEVEL setting; or
amplifier or source check speaker wires
unit is defective for shorts or grounds
Distorted audio Short circuit in Remove speaker leads
and PROTECT speaker or wire one at a time to locate
LED flashes shorted speaker or
wire, then repair
Music lacks Speakers are not Check speaker
“punch” connected properly connections for
proper polarity
GTO Amp OM 2/3/04 3:54 PM Page 7
6

Grand TouringGrand Touring
7

8

HEA-0 1- 156AA HEAT SINK MAIN AL/EXTRUSI O N(L=380.0mm) W/Spray black color 1
PAN-06-255AA PANEL FR O NT EGI, 1.2t W/Painting & silkscreen 1
PAN-06-256AA PANEL REAR EGI, 1.2t W/Painting & silkscreen 1
C O V-22-023A0 WIND O W PLATE ACRYLIC, 3.0t(L=379.5mm) 1
BAD-2 1-004AA BADGE ABS(XR-40 1) W/Hot stamp & silkscreen 1
FOO -2 1-0 12AA FOO T M O UNTING ABS(XR-40 1) W/Spray silkcolor 2
BKT- 14-523A0 BRACKET LAMP SK-5, BK W/Heat treatment 4
BKT- 11 -00 1A0 BRACKET TR(A) SBHG, 11 0.0x22.5x2.0t 2
BKT- 11 -002A0 BRACKET TR(B) SBHG, 11 0.0x25.5x2.0t 2
BKT- 11 -0 11 A0 BRACKET TR(C) SBHG, 200.0x22.5x2.0t 1
BKT- 11 -0 12A0 BRACKET TR(D) SBHG, 200.0x25.5x2.0t 1
SUB-28-00 1A0 CUSHI O N TR BRACKET(A) FIBER, 110.0x22.0x1.0t 2
SUB-28-084A0 CUSHI O N TR BRACKET(B) FIBER, 200.0x22.0x 1.0t 1
SUB-33-00 1A0 CUSHI O N RUBBER RUBBER, 10.0x20.0x1.6t 1
SIL-34-00 1A0 SILICO N PAD SP 1000, 22.0x0.3t 420mm
SS-5 SUPP O RT PCB NYL O N, L=4.8mm 3
SUB-28-5 19A0 PAPER SPACER FIBER, 200.0x8.0x0.5t 2
SC5-NB-30050 SCREW STT2 BH 3x5 NI GR O UND WIRE 1
SC5-BB-30060 SCREW STT2 BH 3x6 BK SIDE PANEL + H/SINK 10
SC5-BB-30080 SCREW STT2 BH 3x8 BK RCA( 1),TERMINAL(3) 4
SC5-NB-30 120 SCREW STT2 BH 3x12 NI PCB + HEAT SINK 3
SC 1-BL-30080 SCREW SML 3x8 BK WIND O W + H/SINK 8
SC 1-NL-40 100 SCREW SML 4x10 NI FOO T+HEAT SINK 10
SC 1-NP-40 140 SCREW SMP 4x14 NI BRACKET TR 8
SC4-NP-40250 SCREW STT 1 PH 4x25 NI ACCESS O RY 4
P O L-3 1- 184A0 P O LY BAG(A) VINYL, 550.0x400.0x0. 1t SET 1
P O L-3 1-007A0 P O LY BAG(B) VINYL, 160.0x280.0x0.03t MANUAL 1
P O L-3 1-008A0 P O LY BAG(C) VINYL, 80.0x100.0x0.03t ACCESS O RY 1
INN-42-004A0 SN O W B O X EPS, 378.0x 140.0x125.0 2
B O X-36- 146AB B O X GIFT SW# 1(B),528.0x385.0x 130.0 1
B O X-39- 157AB B O X CART O N DW#2, 543.0x280.0x4 10.0 1/2
MANUAL ART PAPER 1
SUB-00-00 1A0 SILICAGEL 3g 1
SUB-00-002A0 SC O TCH TAPE WIDTH 20mm 20cm
SUB-00-026A0 O PP TAPE WHITE 3.2m
LAB-QC-000 1A Q C STICKER G O LD/BLACK 1
LAB-SR-0065A SERIAL N O STICKER WHITE/BLACK 4
LAB-MD-000 1A STICKER WHITE/BLACK 1
CAR-WA-0040A WARRANTY CARD ART PAPER 1
LAB-00-0375A WIND O W STICKER "JBL" LO G O 1
LAB-00-0380A E-MARK STICKER WHITE/BLACK 1
LAB-CE-0004A CE STICKER ARTPAPER CLS-AM-2245 1
9

10

11

12

13

PCB-00-00952 IC SHUNT REGULATOR KIA431/KIA431A U505 1
DIO-00-00108 DIODE FAST RECOVERY FR154 D71,72,73,81,82,83 6
DIO-00-00003 DIODE RECTIFIER 1N4004 D1,260 2
DIO-00-00041 DIODE ZENER 0.5W,12V 1N5242 D201,202,301,302,401 5
DIO-00-00006 DIODE SWITCHING SIGNAL 1SS133 / 1N4148 D402,403,404,405,406,407,408,421,422,501 14
D502,503,504,505
TRS-00-00087 TRANSISTOR SMALL SIGNAL PNP "TO-92L" KTA1023Y Q204,206,208,210,304,306,308,310,402,403 11
Q503
TRS-00-00088 TRANSISTOR SMALL SIGNAL NPN "TO-92L" KTC1027Y Q203,205,207,209,270,271,303,305,307,309 12
Q401,502
TRS-00-00090 TRANSISTOR SMALL SIGNAL PNP "TO-92" KTA1266GR Q262 1
TRS-00-00110 TRANSISTOR SMALL SIGNAL NPN "TO-92" KTC3198GR Q101,260,261,263,501 5
RES-00-00401 RESISTOR METAL FILM 1/5WF 100 OHM R204,304 2
RES-00-00463 RESISTOR METAL FILM 1/5WF 220 OHM R203,303 2
RES-00-00474 RESISTOR METAL FILM 1/5WF 240 OHM R405 1
RES-00-00586 RESISTOR METAL FILM 1/5WF 820 OHM R116 1
RES-00-00590 RESISTOR METAL FILM 1/5WF 910 OHM R202,206,302,306 4
RES-00-00437 RESISTOR METAL FILM 1/5WF 1K OHM R151,156 2
RES-00-00393 RESISTOR METAL FILM 1/5WF 1.5K OHM R558 1
RES-00-00482 RESISTOR METAL FILM 1/5WF 2K OHM R117 1
RES-00-00523 RESISTOR METAL FILM 1/5WF 4.7K OHM R113,505,506 3
RES-00-00581 RESISTOR METAL FILM 1/5WF 8.2K OHM R404 1
RES-00-00589 RESISTOR METAL FILM 1/5WF 9.4K OHM R111,112 2
RES-00-00402 RESISTOR METAL FILM 1/5WF 10K OHM R150,155 2
RES-00-00409 RESISTOR METAL FILM 1/5WF 11K OHM R118 1
RES-00-00459 RESISTOR METAL FILM 1/5WF 21K OHM R152,157 2
RES-00-00467 RESISTOR METAL FILM 1/5WF 22K OHM R107,108,109,110 4
RES-00-00537 RESISTOR METAL FILM 1/5WF 47K OHM R103,104,105,106,402,403,503,504 8
RES-00-00636 RESISTOR CARBON FILM 1/5WJ 1 OHM R207,208,211,212,307,308,311,312 8
RES-00-00610 RESISTOR CARBON FILM 1/5WJ 10 OHM R508 1
RES-00-00660 RESISTOR CARBON FILM 1/5WJ 22 OHM R528 1
RES-00-00716 RESISTOR CARBON FILM 1/5WJ 47 OHM R51,52,53,61,62,63 6
RES-00-00606 RESISTOR CARBON FILM 1/5WJ 100 OHM R115,555 2
RES-00-00622 RESISTOR CARBON FILM 1/5WJ 150 OHM R125 1
RES-00-00685 RESISTOR CARBON FILM 1/5WJ 330 OHM R420,421,422,423 4
RES-00-00712 RESISTOR CARBON FILM 1/5WJ 470 OHM R241,264,341 3
RES-00-00723 RESISTOR CARBON FILM 1/5WJ 510 OHM R120,122 2
RES-00-00633 RESISTOR CARBON FILM 1/5WJ 1K OHM R50,60,133,134,153,158,509,521,529,553 11
R554
RES-00-00598 RESISTOR CARBON FILM 1/5WJ 1.5K OHM R511 1
RES-00-00637 RESISTOR CARBON FILM 1/5WJ 2.2K OHM R201,205,301,305,517 5
RES-00-00672 RESISTOR CARBON FILM 1/5WJ 3.3K OHM R522 1
RES-00-00702 RESISTOR CARBON FILM 1/5WJ 4.7K OHM R114,262,414,515,516,552 6
RES-00-00720 RESISTOR CARBON FILM 1/5WJ 5.6K OHM R131,132,272 3
RES-00-00734 RESISTOR CARBON FILM 1/5WJ 6.8K OHM R136 1
RES-00-00608 RESISTOR CARBON FILM 1/5WJ 10K OHM R44,119,123,128,129,130,261,263,406,407 22
R409,410,412,416,418,419,507,525,526,551
R556,559
RES-00-00623 RESISTOR CARBON FILM 1/5WJ 15K OHM R121,126 2
RES-00-00630 RESISTOR CARBON FILM 1/5WJ 18K OHM R415 1
RES-00-00658 RESISTOR CARBON FILM 1/5WJ 22K OHM R101,102,523 3
RES-00-00666 RESISTOR CARBON FILM 1/5WJ 27K OHM R417 1
RES-00-00680 RESISTOR CARBON FILM 1/5WJ 30K OHM R124 1
RES-00-00697 RESISTOR CARBON FILM 1/5WJ 39K OHM R135 1
RES-00-00714 RESISTOR CARBON FILM 1/5WJ 47K OHM R512,513 2
RES-00-00748 RESISTOR CARBON FILM 1/5WJ 75K OHM R514 1
RES-00-00604 RESISTOR CARBON FILM 1/5WJ 100K OHM R138,154,159,230,231,232,236,237,273,330 15
R331,332,336,337,510
RES-00-00620 RESISTOR CARBON FILM 1/5WJ 150K OHM R127,137,270,271 4
RES-00-00654 RESISTOR CARBON FILM 1/5WJ 220K OHM R413 1
RES-00-00755 RESISTOR CARBON FILM 1/5WJ 820K OHM R260 1
RES-00-00635 RESISTOR CARBON FILM 1/5WJ 1M OHM R411,520,524,527 4
RES-00-00639 RESISTOR CARBON FILM 1/5WJ 2.2M OHM R408 1
14

RES-00-00018 RESISTOR METAL FILM 1/2WJ 10 OHM R220,221,222,228,229,320,321,322,328,329 10
RES-00-00040 RESISTOR METAL FILM 1/2WJ 22 OHM R550,557 2
RES-00-00014 RESISTOR METAL FILM 1/2WJ 1.8K R41,42 2
IND-00-00020 INDUCTOR COIL AXIAL 5% 100uH L501 1
CEC-00-00007 CAPACITOR CERAMIC TUBULAR 50V 10pF C105,106 2
CEC-00-00020 CAPACITOR CERAMIC TUBULAR 50V 22pF C155,156,157,158 4
CEC-00-00038 CAPACITOR CERAMIC TUBULAR 50V 47pF C120,510,511,517 4
CEC-00-00028 CAPACITOR CERAMIC TUBULAR 50V 330pF C505,515,516 3
CEC-00-00035 CAPACITOR CERAMIC TUBULAR 50V 470pF C109 1
CEC-00-00004 CAPACITOR CERAMIC TUBULAR 50V 102pF C107,108,111,406 4
CEC-00-00005 CAPACITOR CERAMIC TUBULAR 50V 103pF C524 1
CEC-00-00037 CAPACITOR CERAMIC TUBULAR 50V 473pF C170,171,172,173,174,175,176,177,178,179 12
C180,181
CEC-00-00006 CAPACITOR CERAMIC TUBULAR 50V 104pF C57,73,74,83,84,201,202,204 28
C205,211,261,262,301,302,304,305,341,401
C403,421,512,518,520,523,526,528,529,530
ELC-00-00333 CAPACITOR ELECTROLYTIC"NP" 22uF/16V C504 1
ELC-00-00218 CAPACITOR ELECTROLYTIC"SMS" 1uF/50V C113,408 2
ELC-00-00223 CAPACITOR ELECTROLYTIC"SMS" 2.2uF/50V C525,531 2
ELC-00-00229 CAPACITOR ELECTROLYTIC"SMS" 4.7uF/50V C71,81,114,407,513,522,527 7
ELC-00-00195 CAPACITOR ELECTROLYTIC"SMS" 10uF/16V C110,112,533 3
ELC-00-00197 CAPACITOR ELECTROLYTIC"SMS" 22uF/16V C101,102,103,104,115,121,151,152 8
ELC-00-00198 CAPACITOR ELECTROLYTIC"SMS" 47uF/16V C260 1
ELC-00-00199 CAPACITOR ELECTROLYTIC"SMS" 100uF/16V C75,85,404 3
ELC-00-00214 CAPACITOR ELECTROLYTIC"SMS" 100uF/35V C72,82 2
ELC-00-00200 CAPACITOR ELECTROLYTIC"SMS" 220uF/16V C270 1
MYC-00-00020 CAPACITOR MYLAR 5% 100V 102J C245,345,405 3
MYC-00-00019 CAPACITOR MYLAR 5% 100V 103J C285,385,514 3
MYC-00-00044 CAPACITOR MYLAR 5% 100V 683J C117 1
MYC-00-00045 CAPACITOR MYLAR 5% 100V 823J C116 1
MYC-00-00094 CAPACITOR MYLAR 5% 100V 104J C118,119,222 3
MYC-00-00199 CAPACITOR MYLAR 5% 400V "BOX" 102J C90 1
MYC-00-00088 CAPACITOR MYLAR 5% 63V "TL TYPE" 224J C203,206,303,306 4
MYC-00-00085 CAPACITOR MYLAR 5% 63V "TL TYPE" 105J C2,43,207,209,521,50,3,4,5,6,7,41,42 13
ICO-00-00017 I.C DIP-14 B52 U504 1
ICO-00-00055 I.C DIP-16 F16 U503 1
ICO-00-00003 I.C DUAL OPAMP DIP-08 TL072CP U101,102,103,104,105 5
ICO-00-00006 I.C OPAMP DIP-14 TL074CN U501 1
ICO-00-00170 I.C VOLUME IC DIP-16 NJM 13600 IC101 1
ICO-00-00095 I.C COMPORATOR IC DIP-08 KIA393P U401 1
ICO-00-00157 I.C VOTAGE REGULATOR +12V 1A KIA7812PI U71 1
ICO-00-00162 I.C VOTAGE REGULATOR -12V 1A KIA7912PI U81 1
FET-00-00011 F.E.T N-CH POWER FET "TO-220" IRFZ44R Q51,52,53,61,62,63 6
FET-00-00015 F.E.T N-CH POWER FET "TO-220" IRF540 Q217,218,317,318 4
FET-00-00020 F.E.T P-CH POWER MOSFET "TO-220 IRF9540 Q211,212,213,311,312,313 6
TRS-00-00096 TRANSISTOR SMALL SIGNAL PNP KTA1381 Q202,302 2
TRS-00-00112 TRANSISTOR SMALL SIGNAL NPN KTC3503 Q201,301 2
DIO-00-00152 DIODE FAST RECOVERY YG225D2 D74,75 2
DIO-00-00048 DIODE FAST RECOVERY 1N5404 D2 1
RES-00-01239 RESISTOR MOR-S 1WJ 2.2K OHM R285,385 2
RES-00-01112 RESISTOR MOR-S 2WJ "FORMING 15m/m" 2.2 OHM R253 1
RES-00-01067 RESISTOR MOR-S 2WJ "FORMING 15m/m" 10 OHM R71,81 2
RES-00-01222 RESISTOR MOR-S 2WJ 47 OHM R242,342 2
15

RES-00-00844 RESISTOR MOR-S 2WJ 100 OHM R77 1
RES-00-01078 RESISTOR MOR-S 2WJ "FORMING 15m/m" 1K OHM R250,251 2
RES-00-00853 RESISTOR MOR-S 2WJ 2.2K OHM R209,210,252,309,310,401 6
RES-00-01099 RESISTOR MOR-S 2WJ "FORMING 15m/m" 3.9K OHM R76,86 2
RES-00-00947 RESISTOR SHUNT RESISTOR 5WJ (3P) 0.01 OHM R240,340 2
REN-00-00001 RESONATOR 2.56MHz ZTA2.56MG X501 1
ELC-00-00357 CAPACITOR ELECTROLYTIC"BP" (13x20) 10uF/100V C221 1
ELC-00-00009 CAPACITOR ELECTROLYTIC"BP" (16x25) 33/100V C215 1
ELC-00-00232 CAPACITOR ELECTROLYTIC"SMS" (10x16.5) 220/50V C402 1
ELC-00-00726 CAPACITOR ELECTROLYTIC"WL" (12x25) 1000uF/35V C51,52,53,54,55,56 6
ELC-00-00187 CAPACITOR ELECTROLYTIC "SHL" 2200uF/50V C76,77,86,87,208,210 6
MYC-00-00076 CAPACITOR MYLAR 10% 100V "BOX TYPE" 225K C70,78,80,88,212,223,312,820 8
COI-00-00096 INDUCTOR BAR COIL CL-320 L1 1
COI-00-00093 INDUCTOR BAR COIL CL-510 L6,7 2
COI-00-00073 INDUCTOR DRUM COIL CL-2200 L3 1
COI-00-00070 INDUCTOR DRUM COIL CL-1900C L4 1
COR-TF-00387 CORE 44 PHI MAG T1,44PHI 4T(0.7X18):10T(0.7X4):4T(0.7X1) 1
POWER TERMINAL 3P TERMINAL DST0012-00 TER1 1
SPEAKER TERMINAL4P TERMINAL DST0014-00 TER2 1
HOD-00-00006 FUSE HOLDER PCB TYPE JSF08031P FUSE1,2 2
FUS-AT-00006 AUTO FUSE AUTO FUSE 30A SET(2)+ACCESSORY(2) 4
JAC-00-00043 RCA JACK GOLD PLATE(TOP RED) DJB-554A RCA101 1
JUP-00-00003 JUMPER BAR JUMPER 35m/m BJ3 1
JUP-00-00005 JUMPER BAR JUMPER 55 m/m BJ4 1
JAC-00-00050 MODULAR JACK 4P,BLACK DEK623PCB4-B MOD1 1
REL-00-00008 RELAY DC 30A 12V CT11-D12S REL1 1
THS-00-00013 THERMISTOR FTD5-350 50K TH1 1
VOL-00-00134 SEMI VOLUME 6PHI , 5KB RG06P-5KB VR501 1
VOL-00-00335 VOLUME V12L5(9X5)G(PH2D)N15S 15B20Kx2 VR101,103 2
VOL-00-00336 VOLUME V12L5(9X5)G(PH2D)N15S 15C50Kx2 VR102 1
WIR-00-00015 WIRE #1007 AWG #22 BLACK , 3.2PHI 60m/m W1 1
WIRE #1007 AWG #22 BLACK , 3.2PHI 30m/m W6,7 2
WIR-00-00020 WIRE #1007 AWG #22 BLACK , 3.2PHI 45m/m W2,3,4,5 4
DIO-00-00278 LED 3PHI RED HNRD-3401L LED2 1
DIO-00-00303 LED 3PHI BLUE TOL-30aSBaCAa-B2 LED1 1
2PHI 15m/m W2,3,4,5,6,7 6
TUB-00-00008 TEFLON TUBE 0.7 PHI 10 m/m TH1 2
TUB-00-00009 TEFLON TUBE 0.7 PHI 15 m/m LED1 2
TUB-00-00006 TEFLON TUBE 0.7 PHI 20 m/m LED2 2
ICO-00-00021 I.C SMD PWM TL494C U1 1
ICO-00-00094 I.C SMD "FLP-8" KIA393F U2,3 2
TRS-00-00098 TRANSISTOR SMALL SIGNAL PNP,SOT-23 A1504GR Q3,4,5 3
TRS-00-00113 TRANSISTOR SMALL SIGNAL NPN,SOT-23 C3875GR Q2,6 2
DIO-00-00117 DIODE SWITCHING SIGNAL RLS4148/LL4148 D3,4,5,6 4
16

RES-12-00243 RESISTOR SMD "0805"1/8WF 8.2K OHM R6 1
RES-08-00035 RESISTOR SMD "0805"1/8WF 20K OHM R32 1
RES-08-00048 RESISTOR SMD "0805"1/8WF 27K OHM R33 1
RES-08-00245 RESISTOR SMD "0805"1/8WF 51K OHM R29 1
RES-08-00100 RESISTOR SMD "0805"1/8WF 56K OHM R5 1
RES-08-00249 RESISTOR SMD "0805"1/8WF 110K OHM R28 1
RES-08-00250 RESISTOR SMD "0805"1/8WF 430K OHM R4 1
RES-08-00193 RESISTOR SMD "0805"1/8WJ 4.7 OHM R11 1
RES-08-00163 RESISTOR SMD "0805"1/8WJ 220 OHM R30 1
RES-08-00148 RESISTOR SMD "0805"1/8WJ 1K OHM R16,38,39 3
RES-08-00129 RESISTOR SMD "0805"1/8WJ 1.8K OHM R2 1
RES-08-00151 RESISTOR SMD "0805"1/8WJ 2.2K OHM R9,10 2
RES-08-00156 RESISTOR SMD "0805"1/8WJ 2.7K OHM R3 1
RES-08-00191 RESISTOR SMD "0805"1/8WJ 4.7K OHM R7,8,24,25,27 5
RES-08-00201 RESISTOR SMD "0805"1/8WJ 5.6K OHM R17,18,19 3
RES-08-00132 RESISTOR SMD "0805"1/8WJ 10K OHM R34 1
RES-08-00164 RESISTOR SMD "0805"1/8WJ 22K OHM R12,14,15,22,26 5
RES-08-00170 RESISTOR SMD "0805"1/8WJ 27K OHM R13 1
RES-08-00130 RESISTOR SMD "0805"1/8WJ 100K OHM R20 1
RES-08-00149 RESISTOR SMD "0805"1/8WJ 1M OHM R21,23,31,35 4
RES-12-00189 RESISTOR SMD "1206"1/4WJ 4.7 OHM R1 1
CEC-08-00002 CAPACITOR CHIP"0805" 50V 5% 102P C8 1
CEC-08-00040 CAPACITOR CHIP"0805" 50V 5% 473P C5 1
CEC-08-00004 CAPACITOR CHIP"0805" 50V 5% 104P C18,19,20,22 4
TRS-00-00087 TRANSISTOR SMALL SIGNAL PNP KTA1023Y Q1 1
TRS-00-00090 TRANSISTOR SMALL SIGNAL PNP KTA1266GR Q7,8 2
RES-00-00038 RESISTOR METAL FILM 1/2WJ 220 OHM R36,37 2
ELC-00-00229 CAPACITOR ELECTROLYTIC"SMS" 4.7uF/50V C4,9,11,17,23 5
ELC-00-00197 CAPACITOR ELECTROLYTIC"SMS" 22uF/16V C15,16 2
ELC-00-00199 CAPACITOR ELECTROLYTIC"SMS" 100uF/16V C10,12 2
MYC-00-00020 CAPACITOR MYLAR 5% 100V 102J C13 1
HED-00-00100 HEADER PIN PIN HEADER C-TYPE 6P(R-ANGTM2007-C9G-06P HP1 1
HED-00-00228 HEADER PIN PIN HEADER C-TYPE 8P(R-ANGTM2007-C9G-08P HP2 1
17

18

19