JBL 1500 ARRAY User manual

Project Array™
1500 Array
Subwoofer
Service Manual
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 4/2006

- CONTENTS -
BASIC SPECIFICATIONS …………….……..…………..1
PACKING……..……......................................................2
DETAILED SPECIFICATIONS ……….……..…………..3
CONNECTIONS………………………...……..…...…..…5
OPERATION ……..………………….……...…….….…...6
BASIC TROUBLESHOOTING……………………………7
EXPLODED VIEW/PARTS LIST…….….….…………....8
TEST SET-UP AND PROCEDURE….………………….9
BLOCK DIAGRAM….…………………………………….10
ELECTRICAL PARTS LIST……………………………..11
P.C.B. DRAWINGS….……………...........................….16
IC/TRANSISTOR PINOUTS..……..….…….….….….….22
SCHEMATICS…………………….………………………23
1500 ARRAY SPECIFICATIONS
General
Output 1000W
Low-Frequency Transducer W1500H 15" Pulp-cone driver
Frequency Response (-3dB) 25Hz – 400Hz, variable
Crossover Frequencies 40Hz-140Hz HP
Port 4" Flared
Dimensions (H x W x D) 23" x 19-1/2" x 19" (584mm x 495mm x 483mm)
21" (533mm) Deep with grille
Weight 125 lb (57kg)
JBL continually strives to update and improve existing products, as well as create new ones. The
specifications and details in this and related JBL publications are therefore subject to change without
notice.
1
1500 Array Subwoofer

Ref# Part Number Description Qty
1 361041-002 1500 Array Owner’s Manual 1
2 331994-001 JBL Warranty Card 1
3 361408-001 1500 Array Outer Carton 1
4 354374-001 Packing Foam (Top) 1
5 354374-001 Packing Foam (Bottom) 1
6 340805-006 (Plate) Feet 4
2
1500 Array Subwoofer

1500 Array Powered Sub/ Plate Amp
LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes
US 120VAC/60Hz YES 108-132 120 Vrms Normal Operation
EU 230VAC/50-60Hz YES 207-264 230 Vrms Normal operation, MOMS required
Asia 100VAC/50Hz YES 90-110 100 Vrms Normal operation, MOMS required
Parameter Specification Unit QA Test Limits Conditions Notes
Amp Section
Type (Class AB, D, other) D n/a n/a Bridge type amplifier, None of the speaker terminals
must be connected to system GND at any time.
Load Impedance (speaker) 8 Ohms n/a Nominal
Rated Output Power 650 Watts 593 1 input driven Test frequency 100 Hz
THD @ Rated Power 0.5 % 122K filter
THD @ 1 Watt 0.1 % 0.2 22K filter
Dynamic Power 700 Watts 690
Power is the average measurement
of the first four consecutive peaks of
the burst signal 3/20 Cycles @ 50 Hz, burst test into 8 Ohms, input driven with 800mV RMS
DC Offset 20 mV-DC 100 @ Speaker Outputs
Damping factor >20 DF 15 Measured at amplifier board
Measured at the speaker cable. 500 Watts,
measured at speaker output terminals located at the
amp board.
Input Sensitivity
Input Frequency 100 Hz 100 Nominal Freq.
Line level input 11.69 mVrms ±2dB To 1 Watt Single input driven, Ap Zo=600 Ohms, LFE mode, Volume ctrl. at max.
Signal to Noise
SNR-A-Weighted 100 dBA 95 Relative to rated power (650 Watts) A-Weighting filter
SNR-unweighted 95 dBr 90 Relative to rated power (650 Watts) 22K filter
SNR rel. 1W-unweighted 70 dBr 65 Relative to 1W Output 22K filter
Residual Noise Floor 0.5 mVrms 1Volume @max, LFE Mode, using
RMS reading DMM/VOM (or A/P)
Residual Noise Floor 0.5 mVrms(max) 1
Volume @max, LFE Mode, w/ A/P
Swept Bandpass Measurement
(Line freq.+ harmonics)
Input Impedance Line Input 10K ohms n/a Nominal
Filters
LP 4th order variable 40-140 Hz ± 10
Subsonic filter (HPF) 3rd Ord
e
Fixed Hz ± 10
LFE Mode Fixed Hz ± 10 LP Mode switch at LFE
Features
Line Level output YES functional RCA Line buffered line level output
Volume pot Taper (lin/log) LOG -- functional A Taper
Variable crossover 40-140 Hz YES functional 4th Order LP Filter, 2nd order fix and 2nd order
variable.
LP Selector switch LFE-
Normal YES functional Pass through from the speaker input section
Phase switch YES -- functional Disables LP filter, intended for LFE
Auto- On-Off selector YES functional Switch located at the back panel
Input Configuration
Single Line input YES -- functional Single RCA jack (BLK Color)
Line output configuration
Single Line level output YES Functional Gain=0dB respect to line level input,
Zo=600 Ohms Single RCA jack (BLK Color)
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES functional Auto - on selection switch in Auto
ATO Input test frequency 50 Hz functional "
ATO Level, Line Input 2.5 mV functional "
ATO Turn-on time 2 seconds functional Amp connected and AC on, then
input signal applied
Auto Mute/ Turn-OFF Time 15 minutes 17 (T) Time before muting, after input
signal is removed Auto turn of time (T) must be 10 > T < 17 Minutes
Power on Delay time
ATO mode 4 sec. 5After applying the minimum ATO voltage (2mVRMS)
ON mode 2 sec. 2After turning the stand-by knob to ON position
3
1500 Array Subwoofer

Parameter Specification Unit QA Test Limits Conditions Notes
Transients/Pops
ATO Transient 5 mV-peak n/a @ Speaker Output
Turn-on Transient 50 mV-peak 1V-pk-pk @ Speaker Output AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 1V-pk-pk @ Speaker Output AC Line cycled from ON to OFF
Efficiency
Efficiency 73 % 70 500W of output power into rated
impedance Nominal Line voltage
Stand-by Input Power 2 3@ nominal line voltage, Amp in
OFF state, RED LED activated Maximum allowable input power LED in RED, Class D inactive
Stand-by Input Power 10 Watts 8@ nom. line voltage, Amp in On
state, Green LED activated
Maximum allowable input power under nominal
Input voltage and frequency, in stand-by mode
(HOT or COLD operation, LED GREEN). Class D
active but no stimulus signal applied.
Power Cons. @ 500W 678 Watts 714 @ nom. line voltage 500 Watts into rated impedance 8 Ohms
Protection
Thermal Protection YES functional @1/8 max unclipped Power
Temperature
rise
in
accessible
metal
parts
should
not exceed 35K rise for domestic version or 30K
rise for European versions (refer to requirements
sheet). Unit is protected for over-temperature
conditions
DC Offset Protection YES -DC present at Speaker Out leads Relay opens during a DC output condition
Line Fuse Rating
Japan 100V & USA- Versions 6.3 Amps Type-T or Slo Blo-250 V UL, PSE Approved
Europe 220-240V 3.15 Amps Type-T, Low breaking capacity-250
V
SEMKO Approved
4
1500 Array Subwoofer

SPEAKER CONNECTIONS
S
Su ub bw wo oo of fe er rC Co on nt tr ro ol ls sa an nd dC Co on nn ne ec ct ti io on ns s( (1 15 50 00 0A Ar rr ra ay yO On nl ly y) )
0
1
2
34
567
8
The 1500 Array includes
a line output. This output
allows you to “daisy chain”
one 1500 Array to multiple
1500 Array subwoofers.
Simply connect the first
subwoofer as described
above and then run a
subwoofer cable from the
line output(s) to the line
input on the next sub.
¡Line-Level Input
™Line-Level Output
£Power Indicator
¢Subwoofer Level (Volume) Control
∞Crossover Adjustment
§Phase Switch
¶LP/LFE Selector
•On/Off Auto Switch
ªPower Switch
Connection:
If you have a Dolby®Digital or DTS®
receiver/processor with a low-frequency-
effects (LFE) output, set LFE/LP switch to
LFE. If you prefer to use the crossover
built into the 1500 Array, set the LFE/LP
Switch ¶to LP.
SUBWOOFER OR
LFE OUTPUT
SUBWOOFER OR
LFE OUTPUT
Project Array OM 1/10/06 12:21 PM Page 8
5
1500 Array Subwoofer

Power On
Plug your subwoofer’s AC cord
into a wall outlet. Do not use
the outlets on the back of the
receiver.
Initially set the Subwoofer
Level (Volume) Control ¢to
the “min” position.
Turn on your sub by pressing
the Power Switch ªon the
rear panel.
Auto On/Standby
With the Power Switch ª
in the “on” position, the Power
Indicator LED £will remain
backlit in red or green to
indicate the On/Standby
mode of the subwoofer.
RED = STANDBY (No signal
detected, Amp Off)
GREEN = ON (Signal detected,
Amp On)
The subwoofer will auto-
matically enter the Standby
mode after approximately 10
minutes when no signal is
detected from your system.
The subwoofer will then power
ON instantly when a signal is
detected. During periods of
normal use, the Power Switch
ªcan be left on. You may turn
off the Power Switch ªfor
extended periods of non-
operation, e.g., when you are
away on vacation.
If the Auto Switch •is in the
“on” position, the subwoofer
will remain on.
Adjust Level
Turn on your entire audio
system and start a CD or movie
soundtrack at a moderate
level. Turn up the Subwoofer
Level (Volume) Control ¢
about halfway. If no sound
emanates from the subwoofer,
check the AC-line cord and
input cables. Are the con-
nectors on the cables making
proper contact? Is the AC
plug connected to a “live”
receptacle? Has the Power
Switch ªbeen pressed to
the “on” position? Once you
have confirmed that the sub-
woofer is active, proceed by
playing a CD or movie. Use a
selection that has ample bass
information.
Set the overall volume control
of the preamplifier or stereo
to a comfortable level. Adjust
the Subwoofer Level (Volume)
Control ¢until you obtain a
pleasing blend of bass. Bass
response should not over-
power the room but rather
should be adjusted so there is
a harmonious blend across the
entire musical range. Many
users have a tendency to set
the subwoofer volume too
loud, adhering to the belief
that a subwoofer is there to
produce lots of bass. This is
not entirely true. A subwoofer
is there to enhance bass,
extending the response of
the entire system so the bass
can be felt as well as heard.
However, overall balance
must be maintained or the
music will not sound natural.
An experienced listener will
set the volume of the sub-
woofer so its impact on bass
response is always there but
never obtrusive.
Crossover Adjustments
NOTE: This control will have
no effect if the LP/LFE Selector
Switch ¶is set to “LFE.” If
you have a Dolby Digital or
DTS processor/receiver, the
Crossover Frequency is set
by the processor/receiver.
Consult your owner’s manual
to learn how to view or change
this setting.
The Crossover Adjustment
Control ∞determines the
highest frequency at which the
subwoofer reproduces sounds.
If your main speakers can
comfortably reproduce some
low-frequency sounds, set this
control to a lower frequency
setting, between 50Hz and
100Hz. This will concentrate
the subwoofer’s efforts on
the ultradeep bass sounds
required by today’s films and
music. If you are using smaller
bookshelf speakers that do
not extend to the lower bass
frequencies, set the Crossover
Adjustment Control to a higher
setting, between 120Hz and
150Hz.
Phase Control
The Phase Switch §deter-
mines whether the subwoofer
speaker’s pistonlike action
moves in and out with the main
speakers (0˚) or opposite the
main speakers (180˚). Proper
phase adjustment depends
on several variables, such as
subwoofer placement and
listener position. Adjust the
Phase Switch to maximize
bass output at the listening
position.
1500 ARRAY OPERATION
Project Array OM 1/10/06 12:21 PM Page 9
6
1500 Array Subwoofer

BASIC TROUBLESHOOTING
If there is low (or no) bass output
•Make sure the connections to the left and right “Speaker
Inputs” have the correct polarity (+ and –).
•Make sure the subwoofer is plugged into an active electrical
outlet.
•Make sure the Power Switch is on.
•In Dolby Digital or DTS modes, make sure your
receiver/processor is configured so that the subwoofer
and LFE output are enabled.
•Adjust the Subwoofer Level Control
7
1500 Array Subwoofer

1500 ARRAY MECHANICAL PARTS LIST
Item # Description Part Number Qty
1 CABINET ASSEMBLY-1500 ARRAY Not for Sale 1
2 15" WOOFER-W1500H 353721-001 1
3 AMPLIFIER ASSEMBLY,120V-ARRAY Not for Sale 1
4 POWER TRANSFORMER-1500 ARRAY BG 361407-001 1
5 PORT TUBE -1500 ARRAY 360806-001 1
6 CARBOARD TUBE,4 1/4x4x1/8x6-4338 47909-68 1
7 FOOT,NUT,INSERT,BLK 340805-004 4
8 FOOT,SPIKE,BLK 340805-005 4
9 GRILLE,FRONT, 1500 ARRAY 354507-001 1
10 WOOFER SCREW,10-32 X 1,FIL,PH,BLK ZINC,LCS 804-01110-16 8
11 AMPLIFIER SCREW,8 X 1,PAN,PH,PB,BLK ZINC,LCS 883-41110-16 10
12 GASKET,DRVR,15" 338073-001 1
13 LOGO-JBL 360813-001 1
1500 ARRAY SUB EXPLODED VIEW
X RAY VIEW FOR
ILLUSTRATIVE PURPOSES ONLY
DAMPING MATERIAL NOT SHOWN
8
1500 Array Subwoofer

1500 Array TEST PROCEDURE
Equipment needed:
•Function/signal generator/sweep generator
•Multimeter
•RCA cable
General Unit Function (UUT = Unit Under Test)
Switch/Controls:
GAIN control full Counterclockwise (Min)
CROSSOVER (Hz) Full Clockwise (140)
PHASE switch - either position
LFE/LP – LP position
1) From the signal generator, connect one line level (RCA) cable to the Line In jack on the UUT.
2) Turn on generator; adjust to 200mV, 50 Hz.
3) Plug AC power cord in UUT, turn power switch ON.
4) LED should be ON (faceplate). Turn up LEVEL control to full Clockwise (Max).
5) LED should be Green; Bass response should be heard and felt vigorously from woofer and port tube.
6) Turn LEVEL control full Counterclockwise (Min). Turn power switch OFF.
Sweep Function
1) Follow steps 1-5 above, using a sweep generator as a signal source – adjust the generator to 75mV, 50 Hz.
2) Sweep generator from 20Hz to 300Hz. Listen for any rattles, clicks, buzzes or any other noises. If any unusual
noises are heard, test woofer according to the instructions below.
Driver Function
1) Remove woofer from the enclosure.
2) Check DC resistance of woofer; it should be 5.9 Ω±10%,
3) Connect a pair of speaker cables to woofer terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 6.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
1500 Array Subwoofer

1500 ARRAY BLOCK DIAGRAM
10
1500 Array Subwoofer

1500 Array 120V Electrical parts lis
t
Part numbe
r
Qt
y
Description Reference Designato
r
DRIVER PCB
Resistors
024-000098-120ZS 4 GS SMD Resistor 0R 1/8W J 0805 R313,314,318,320
024-100298-120ZS 4 GS SMD Resistor 10R 1/8W J 0805 R89,90,140,150
024-100498-120ZS 10 GS SMD Resistor 1K 1/8W J 0805 R81,85,96,97,131,137,142,147,162,179
024-100598-120ZS 12 GS SMD Resistor 10K 1/8W J 0805 R75,83,92,98,132,133,151,156,163,164,183,82,
024-110598-120ZS 2 GS SMD Resistor 11K 1/8W J 0805 R74,99
024-200598-120ZS 4 GS SMD Resistor 20K 1/8W J 0805 R95,141,148,181
024-220398-120ZS 2 GS SMD Resistor 220R 1/8W J 0805 R136,167
024-220498-121ZS 1 GS SMD Resistor 2K2 1/8W J 0805 R134
024-220598-120ZS 1 GS SMD Resistor 22K 1/8W J 0805 R37
024-220798-120ZS 2 GS SMD Resistor 2M2 1/8W J 0805 R87,93
024-270498-120ZS 3 GS SMD Resistor 2K7 1/8W J 0805 R80,84,157
024-390498-120ZS 2 GS SMD Resistor 3K9 1/8W J 0805 R130,161,
024-390598-120ZS 2 GS SMD Resistor 39K 1/8W J 0805 R86,94
024-470398-120ZS 1 GS SMD Resistor 470R 1/8W J 0805 R91
024-470498-120ZS 4 GS SMD Resistor 4K7 1/8W J 0805 R34,36,152,153
024-470598-120ZS 1 GS SMD Resistor 47K 1/8W J 0805 R35
024-470698-120ZS 2 GS SMD Resistor 470K 1/8W J 0805 R32,33
024-560598-120ZS 1 GS SMD Resistor 56K 1/8W J 0805 R38
024-680498-120ZS 2 GS SMD REsistor 6K8 1/8W J 0805 R135,166
Capacitors
031-100244-100ZS 4 GS SMD Ceramic cap. 0u01/50V K 0805 X7R C108,118,131,140
031-100343-100ZS 2 GS SMD Cap. 100pF/50V J 0805 NPO C81,84
031-100344-100ZS 6 GS SMD Cap. 0u1/50V K 0805 X7R C75-78,82,85
031-180344-100ZS 2 GS SMD Cap. 0u18/50V K 0805 X7R C80,83
031-470244-102ZS 4 GS SMD Cap. 0u047/50V K 0805 X7R C93,94,101,124
031-560243-100ZS 4 GS SMD Cap. 56pF/50V J 0805 NPO C92,102,105,125
031-560343-102ZS 1 GS SMD Cap. 560pF/50V J 0805 NPO C79
034-100614-300ZS 1 GS Elec. Cap. 100uF/16V M (R)0611 P:2.5 C117
Semiconductors
054-000100-100ZS 2 GS SMD DIODE: PN:ES1D 200V 1A D35,43
054-005501-100ZR 1 GR SMD ZENER DIODE PN:BZV55C3V6 (PHILIPS) D60
054-007200-100LZS 2 GS SMD IC: (JRC) M072M-DUAL OP-AMP U9,10
054-008406-000ZR 2 GR SMD ZEN DIODE:(PHILIPS) BZX84C10-7-F SOT-23 D42,49
054-008408-000ZR 2 GR SMD ZEN DIODE:(PHILIPS) BZX84C5V6-7-F SOT-23 Z7,8
054-033906-100ZR 2 GR SMD Transistor (ON) PN:MMBT3906LT1G SOT23 Q34,35
054-414803-100ZS 5 GS SMD DIODE: PN:LL4148 MINI-MELF D36,39,46,52,61
054-540100-100ZR 2 GR SMD Transistor PNP (ON SEN) MMBT5401 LT1 SOT-23 Q33,40
054-555100-100ZR 1 GR SMD Transistor (NPN) PN:MMBT5551 LT1R (ON) Q32
051-222200-100ZR 2 GR Transistor NPN (ON SEM) PN:MPS2222ARLRAR TO-92 Q20,22
051-555100-000ZR 2 GR Transistor NPN PN:2N5551 TO-92 Q21,23
051-000600-100ZR 1 GR Transistor NPN PN:MPSW06RLRA TO-92 (ON) Q31
053-211100-000ZR 2 GR IC:DIP,HALF-BRIDGE DRIVER PN:IR2111 8PIN (IR) U7,8
Miscellaneous
072-040229-000ZR 1 GR HEADER Right Angle PN:211-107-000-400 7PIN PIN2
072-040230-000ZR 1 GR HEADER Right Angle PN:211-111-000-400 11PIN PIN1
PREAMP PC
B
Resistors
024-000097-120ZS 5 GS SMD Resistor PN:1206J000 0R 1/4W J 1206 R258,290,297,302,303,
024-100497-100ZS 4 GS SMD Resistor PN:1206F102 1K 1/4W F 1206 R238,264,288,291
024-100598-121ZS 15 GS SMD Resistor 10K 1/4W J 1206 R202,206,207,212,222,235,252-254,257,228,229,262,268,284
024-150498-121ZS 1 GS SMD Resistor 1K5 1/4W J 1206 R251
024-150598-100ZS 1 GS SMD Resistor 15K 1/8W F 0805 R223,
024-200597-100ZS 5 GS SMD Resistor PN:1206F203 20K 1/4W F 1206 R256,208,209,231,232
024-220298-121ZS 1 GS SMD Resistor 22R 1/4W J 1206 R249
11
1500 Array Subwoofer

Part numbe
r
Qt
y
Description Reference Designato
r
PREAMP PC
B
024-220397-120ZS 1 GS SMD Resistor 220R 1/4W J 1206 R255
024-237598-120ZS 1 GS SMD Resistor 23K7 1/8W F 0805 R281
024-270498-121ZS 1 GS SMD Resistor 2K7 1/4W J 1206 R237
024-330397-120ZR 2 GR SMD Resistor 330R 1/4W J 1206 R211,282
024-330498-121ZS 1 GS SMD resistor 3K3 1/4W J 1206 R240
024-330598-121ZS 4 GS SMD resistor 33K 1/4W J 1206 R298,406,408,414
024-365697-100ZR 1 GR SMD resistor 365K 1/4W F 1206 R285
024-402597-100ZS 1 GS SMD resistor 40K2 1/4W F 1206 R260
024-432598-100ZR 1 GR SMD resistor 43K2 1/8W F 0805 TPAING R214
024-470598-121ZS 1 GS SMD resistor 47K 1/4W J 1206 R280
024-470698-121ZS 1 GS SMD resistor 470K 1/4W J 1206 R259
024-470797-100ZS 2 GS SMD resistor 4M7 1/4W F 1206 R244,243
024-536597-100ZR 1 GR SMD resistor 53K6 1/4W F 1206 R283
024-560598-121ZS 1 GS SMD resistor 56K 1/4W J 1206 R224
024-620398-121ZS 2 GS SMD resistor 620R 1/4W J 1206 R221,226,
024-680498-121ZS 1 GS SMD resistor 6K8 1/4W J 1206 R247
024-680598-121ZS 1 GS SMD resistor 68K 1/4W J 1206 R250
024-820598-121ZS 1 GS SMD resistor 82K 1/4W J 1206 R263
021-432598-100ZS 1 GS Metal film 43K2 1/8W F R214
021-475498-100ZR 1 GR MF resistor 4K75 1/8W F R204
026-500495-005ZS 1 GS VR 5K PN:RD163111R22B-5K15A-EJ GAIN R216
026-500595-267ZS 1 GS VR 50KBx4 PN:RD1631411001D-50KBx4 R233
Capacitors
031-100244-101ZS 2 GS SMD cap. 0u01/50V K 1206 X7R C12,13
031-100344-102AZS 8 GS SMD cap. 0u1/50V K 1206 X7R C227,229,230,232-235,200
031-100344-104AZS 1 GS SMD cap. 100pF/50V K NPO 1206 C222
031-220344-106AZS 3 GS SMD cap. 220pF/50V K X7R 1206 C215,216,204
031-270244-100ZR 1 GR SMD cap. 0u027/50V K 0805 X7R C280
031-270444-101 1 SMD cap. 2700pF/50V K 1206 X7R C224
031-470144-101AZS 2 GS SMD cap. 0u0047/50V K 0805 X7R C2G1,C281
031-680144-100ZS 1 GS SMD cap. 0u0068/50V K 0805 X7R C212
034-100515-304ZS 2 GS elec. Cap. 10uF/16V M (R)0511 P:2.5 TAPIN C220,237
034-100615-301ZS 1 GS Elec. Cap. 100uF/16V M (R)0611 P:5 C221
034-220516-301ZS 6 GS elec. Cap. 22uF/16V M (R)0511 P:2 C223,416,14,15,411,415
035-100343-300ZS 1 GS PE Cap. 0uF1/50V J P:5 C213
035-220243-100ZR 1 GR PE Cap. FE-M 0u022/63V J P:5m/m C202
035-330293-300ZR 2 GR PE Cap. PN:ESK063S33JT 0u033/63V J P:5 C209,218
035-470353-302ZR 2 GR PE Cap. P:5 0u47/63V J P/N:R82DC347DQJ C207,208
035-680253-300ZR 1 GR PE Cap. FE-M PN:ESK063S68JT 0u068/63V J P:5mm C201
033-330515-300ZS 2 GS NPE cap. 33uF/16V M (R)0511 P:2 C214,225
Semiconductors
054-007200-100LZS 6 GS SMD IC: (JRC) M072M-DUAL OP-AMP U200-205
054-011400-100ZR 1 GR SMD Transistor PN:DTC114TKA SMT3 (ROHM Q202
054-390402-100ZR 2 GR SMD Transistor (SC00044) PN:MMBT3904TR(Fairchild) Q203,204
054-414803-100ZS 14 GS SMD DIODE: PN:LL4148 MINI-MELF D201,204,207,209,212,216,218,219,405,413,414,217,203,200,
054-523701-100ZR 1 GR SMD ZENZER DIODE: (GMT) GMBZ5237B 8V2 SOT23 D206
050-505200-001ZS 1 GS LED PN:LT-2402-21 LED1
051-011100-100ZR 1 GR JFET N-Channel PN:J111 TO-92 (FAIRCHILD Q200
Miscellaneous
072-010360-000ZR 1 GR RCA JACK PN:B217CK J201
072-040008-110ZS 1 GS Terminal housing PN:JS-1001-08 8P P:2.5 P2
074-030002-000ZR 2 GR TOGGLE SW PN:L101-T2B4QE LFE, PHASE SW201,202
074-030018-000ZR 1 GR TOGGLE SW PN:L103-T2-B4 AUTO ON-OFF SW200
FUSE PCB
073-050001-000ZS 2 GS FUSE CLIP P/N:CT-FH1206 for F1
091-000132-000ZR 1 GR FUSE T6.3A/250V GSL-6.3 φ5x20m/m F1
072-040039-000ZR 3 GR (PCB TYPE) PC205 (t=0.8m/m) T205MA T2,TER5,6,
072-040064-000ZR 1 GR Terminal (PCB TYPE) PC250 (t=0.8m/m) T250MA TER1
039-220384-100ZR 2 GR X2 Safety Cap. 0u22/250V HQX0.22K275VX2 18x16.5x8.5 CXAC1,CXAC2
043-155300-000ZR 1 GR COIL PN:YT-13192 155uH±10% L7
12
1500 Array Subwoofer

Part numbe
r
Qt
y
Description Reference Designato
r
FUSE PCB
043-324300-000ZR 1 GR INDUCTOR 324uH YT-10778 L13
025-006000-000ZR 1 GR Thermister P/N:CL-60 TH3
POWER PCB
Capacitors
032-100484-200ZS 3 GS END Mylar cap. 1uF/250V K P:15 C410,418,427
034-680794-200ZR 4 GR Elec. Cap. (LP) 85℃6800uF/80V M (R)3050 P:10 C420-423,
030-180384-300ZR 1 GR Ceramic cap. 180pF/250V K X7R P:5 C419( in series with R403 T400 pin2-5)
031-220364-100ZS 1 GS SMD Cap. 0u22/100V K 1206 X7R C424
031-100384-100RZS 2 GS SMD cap.0u1/250V K 1206 X7R C428,429
031-100344-102AZS 4 GS SMD cap. 0u1/50V K 1206 X7R C417,401-403,
031-100244-101ZS 3 GS SMD cap. 0u01/50V K 1206 X7R C404-406
034-220625-300ZS 2 GS electrolytic cap. 220uF/25V M (R)0812 P:5 C414,413
034-330625-300ZS 1 GS elec. Cap. 330uF/25V M (R)1013 P:5 C412
034-470415-300ZS 1 GS electrolytic cap. 4u7/50V M (R)0511 P:2.0 C407
034-470515-200ZR 1 GR elec. Cap. 47uF/16V M (R)0511 P:2.5 C408
034-220516-301ZS 6 GS electrolytic cap. 22uF/16V M (R)0511 P:2 C223,416,14,15,411,415
035-100464-300ZR 2 GR ESK mylar cap. 1u/100V K P:5 C425,426
Resistors
028-100301-020ZR 1 GR FUSIBLE RES 100R 1W J R403(C419 in sereis with C403 T400 pin2-5)
024-910498-120ZS 2 GS SMD resistor 9K1 1/8W J 0805 R413,415
024-470398-121ZS 2 GS SMD resistor 470R 1/4W J 1206 R401,402
024-100598-101ZS 4 GS SMD resistor PN:1206F103 10K 1/4W F 1206 R409,416,417,405
024-220498-120ZS 1 GS SMD resistor 2K2 1/4W J 1206 R400
Semiconductors
054-008407-000ZR 3 GR SMD ZEN DIODE:(PHILIPS) PN:BZX84C15-7-F SOT-23 D400,402,403
054-000100-100ZR 4 GR GS SMD DIODE: PN:ES1D 200V 1A (PANJIT) D406-409
050-013000-100 1 DIODE TVZ:DIP PN:P6KE130A (CONCORD) D404
051-000600-100ZR 1 GR transistor NPN PN:MPSW06RLRA TO-92 (ON) Q406
051-005600-100ZR 1 GR transistor PNP PN:MPSW56RLRAR TO-92 (ON Q408
051-003100-000ZS 1 GS transistor NPN PN:TIP 31C TO-220 (MOSPEC) Q404
054-390402-100ZR 1 GR SMD Transistor (SC00044) PN:MMBT3904TR(Fairchild) Q402
052-150400-000ZR 1 GR bridge rectifier PN:GBJ1504 BR400
053-010200-000 1 IC:DIP PN:TOP102YAI (PWM Switch) U400
Miscellaneous
044-100100-000ZS 3 GS SMD FERRITE BEAD PN:321611 600R/100MHz 1206 FB403-405
044-100103-000ZS 1 GS SMD FERRITE BEAD PN:321611 800R/100MHz 1206 FB406
043-560200-000ZR 1 GR INDUCTOR 56uH YT-10779 L400
072-040064-000ZR 2 GR Terminal (PCB TYPE) PC250 (t=0.8m/m) T250MA TER401,404
042-010115-000ZR 1 GR X'former PN:YT-13167 KAPPA-1000 T400
DAUGHTER PCB (Attached to Power PCB
)
054-033904-100ZR 1 SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 ING Q403B
054-033906-100ZR 1 SMD transistor (ON) PN:MMBT3906LT1G SOT23 ING Q405B
054-414803-100ZS 1 GS SMD DIODE:PN:LL4148 MINI-MELF ING D410B
024-100598-120ZS 2 GS SMD resistor 10K 1/8W J 0805 ING R404B,R407B
024-220298-120ZS 1 GS SMD resistor 22R 1/8W J 0805 ING R412B
034-100444-300ZR 1 GR electrolytic cap. 1uF/50V K (R)0511 P:5 TAING C430B
072-040337-000ZR 1 HEADER Right Angle PN:211-110-000-400 10PIN CONNECT
MAIN PCB
Resistors
024-100498-120ZS 1 GS SMD resistor 1K 1/8W J 0805 R119
024-100598-120ZS 17 GS SMD resistor 10K 1/8W J 0805 R1,4,7,16,121-123,126,128,138,165,168,170,125,143,169,19,
024-100698-120ZS 1 GS SMD resistor 100K 1/8W J 0805 R120
024-130598-120ZS 1 GS SMD resistor 13K 1/8W J 0805 R118
13
1500 Array Subwoofer

Part numbe
r
Qt
y
Description Reference Designato
r
MAIN PCB
024-150598-100ZS 2 GS SMD resistor 15K 1/8W F 0805 R20,21
024-220298-121ZS 2 GS SMD resistor 22R 1/4W J 1206 R28,29
024-220498-121ZS 4 GS SMD resistor 2K2 1/8W J 0805 R17,31,110,139
024-220598-120ZS 1 GS SMD resistor 22K 1/8W J 0805 R127
024-332498-100ZS 1 GS SMD resistor 3K32 1/8W F 0805 R22
024-332598-101ZS 2 GS SMD resistor 33K2 1/8W F 0805 R60,60B
024-392498-100ZR 1 GR SMD resistor 3K92 1/8W F 0805 R63
024-470398-120ZS 4 GS SMD resistor 470R 1/8W J 0805 R145,155,177,186
024-470598-120ZS 2 GS SMD resistor 47K 1/8W J 0805 R3,171
024-560298-120ZS 4 GS SMD resistor 56R 1/8W J 0805 R24-27
024-560498-120ZS 1 GS SMD resistor 5K6 1/8W J 0805 R30
024-560598-120ZS 1 GS SMD resistor 56K 1/8W J 0805 R15
024-680498-120ZS 1 GS SMD resistor 6K8 1/8W J 0805 R23
Capacitors
031-100144-103ZS 1 GS SMD cap. 0u001/50V K 0805 X7R C130
031-100144-106ZS 2 GS SMD cap. 0u01/50V K 0805 X7R C27,28
031-100344-100ZS 1 GS SMD cap. 0u1/50V K 0805 X7R C116
031-100364-100ZS 7 GS SMD cap. 0u1/100V K 1206 X7R C5,6,69,112,115,135,138
031-100384-100RZS 1 GS SMD cap. 0u1/250V K 1206 X7R C39B
031-220344-300ZS 1 GS SMD cap. 220pF/50V K 0805 NPO C40
031-470144-101ZS 1 GS SMD cap. 0u0047/50V K 0805 X7R C1G1
031-470344-100ZS 1 GS SMD cap. 470pF/50V K 0805 X7R C123
034-100715-300ZS 2 GS elect. Cap. 1000uF/16V M (R)1017 P:3.5 C109,132
034-330615-301ZS 1 GS elec. Cap. 330uF/16V M (R)0812 P:3.5 loose package C32
032-100484-200ZS 5 GS END mylar cap. 1uF/250V K P:15 C30,37,39,C31,38
033-330494-270ZS 2 GS NPE cap. ELYTONE 3u3/63V K10 (R) 8x13 TBE C114,137
033-680464-270ZS 2 GS NPE cap. 印ELYTONE 6u8/100V K10 (R)1020 GNE C113,136
034-820794-200ZR 2 GR elec. Cap. (LP) 85℃8200uF/80V M (R)3545 P:10 C1,4
034-100625-300ZS 1 GS elect. Cap. 100uF/25V M (R)6.3x11 P:5 C62
034-220525-300ZR 2 GR elec. Cap. 22uF/25V M (R)5x11 P:2.5 TAPIN C25,26
034-220615-300ZS 1 GS elect. Cap. 220uF/16V M (R)0611 P:2.5 C8
034-220625-300ZS 1 GS elec. Cap. 220uF/25V M (R)0812 P:5 C100
Resistors
021-100402-021ZS 2 GS MOF resistor 1K 2W J FK TYPE R173,48
022-005105-020ZS 1 GS resistor PN:SQM 0R05 5W J 25x13 R2
020-220496-100ZS 1 GS film resistor 2K2 1/2W J R6
Semiconductors
054-000100-100ZS 5 GS SMD DIODE: PN:ES1D 200V 1A D23,37,40,44,47
054-008409-000ZR 1 GR SMD ZENER DIODE:(PHILIPS) BZX84C3V0-7-F SOT-23 D32
054-033904-100ZR 7 GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 Q28,29,50,51,127,128,130
054-033906-100ZR 2 GR SMD transistor (ON) PN:MMBT3906LT1G SOT23 Q30,38
054-290701-100ZR 1 GR SMD transistor (ON) PN:MMBT2907ALT1 SOT-23 Q52
054-414803-100ZS 15 GS SMD DIODE:PN:LL4148 MINI-MELF D1,4-6,21,22,31,33,34,38,41,45,48,53,54
054-540100-100ZR 3 GR SMD transistor PNP (ON SEN) MMBT5401 LT1 SOT-23 Q1,2,26
054-555100-100ZR 1 GR SMD transistor (NPN) PN:MMBT5551 LT1R (ON) Q25
051-359400-000ZR 4 GR MOSFET N-CHANNEL PN:2SK3594-01SC (FUJI) Q11,13,15,17
051-290700-100ZR 4 GR Transistor PNP (ON) PN:MPS2907A RLRAR TO-92 Q12,14,16,18
051-540101-000ZR 1 GR Transistor PNP(FAIRCHILD PN:2N5401 TO-92 Q3
Miscellaneous
072-040039-000ZR 8 GR terminal (PCB TYPE) PC205 (t=0.8m/m) T205MA TER402,403,406,407,TER2,4,8,3
044-100100-000ZS 2 GS SMD FERRITE BEAD PN:321611 600R/100MHz 1206 FB1,2
025-010300-000ZR 1 GR thermister PN:NTSE103KZ072 K L:50mm TH1
025-210100-000ZS 1 GS thermister (PTC) PN:PTMS2101RP516Y TH2
043-110300-000ZR 1 GR COIL PN:YT-13141 110uHx2±10% L8 (L8+L11)
043-300101-000ZR 2 GR INDUCTOR PN:YT-10033 30uH L9,10
043-560200-000ZR 1 GR INDUCTOR 56uH YT-10779 L12
072-040007-000ZS 1 GS terminal housing SWA101 PN:JS-1001-07 7P P9
072-040008-110ZS 1 GS terminal housing PN:JS-1001-08 8P P:2.5 P1
072-040064-000ZR 2 GR terminal (PCB TYPE) PC250 (t=0.8m/m) T250MA T1,TER7
073-111003-000ZR 1 GR shorting strap 54.9x13.6x1mm J7
14
1500 Array Subwoofer

Part numbe
r
Qt
y
Description Reference Designato
r
Mechanical Parts
073-111004-000ZR 1 GR shorting strap 29.5x12.4x0.8m/m J9
074-300018-000ZR 1 GR RELAY PN:943-1C-48D K1
008-061215-000ZR 1 GR GASKET C4305 12x15 t=5mm CR spa thermistor
008-061602-022ZR 2 GR GASKET CR4305 spa 155.8x16.8 t=1.5mm (UL94-HF1) plate x2
008-063702-002ZR 2 GR GASKET CR4305 spa 372.3x16.1 t=1.5mm (UL94-HF1) Plate x2
008-065757-002ZR 1 GR GASKET CR4305 spa 56.9x57.2 t=1.0mm (UL94-HF1) X'FORMERPLATE
061-001052-000ZS 2 GS Knob w/white indicator 49001-W (18 t)D=15.1 H=14.5 GAIN, CROSSOVER KNOBS
061-100016-000ZR 7 GR post PN:BCMS-8 L=8mm NYLON 66(UL) POWER PCBx4,FUSE PCBx3
061-700044-000ZR 2 GR mica 13x18mm TO-220 holeless for Q13,17
061-700090-900ZR 2 GR ceramic washer 16x21mm t=2mm white for Q11,15
061-700119-000ZR 1 GR insulator 114.3x84mm t=0.254mm FR700 POWER PCB
061-701003-000ZR 1 GR insulator w/adhesive M 467 170x85mm t=0.432mm bracket+plate
063-010010-000ZR 5 GR Transistor Bracket P/N:TRK-2 for Q11,13,15,17,TH1
063-060606-000ZR 1 GR X'FORMER PLATE SPCC 56.9x57.2 t=2.0mm
063-401602-000ZR 1 GR Plate SPCC (1500 Array) 402x156.8 t=2.3mm
073-014103-500ZR 1 GR Bracket (HB5000) 6.64"x3.5"x3.2" SPCC platex1
073-032141-600ZR 1 GR Heatsink (HB5000) 82.8x120.7x19.1mm black anodiz bracketx1
074-020005-000ZR 1 GR 2-pin AC socket P/N 3516-T3C02 AC POWER Receptacle
074-020018-000ZR 1 GR ROCKER SW (AC POWER) PN:RF1003-BB4-0 SW4
086-021836-004ZR/120V 1GR Power cord SJT 16AWGx2C L=3660mm WS004+WS002E AC POWER Cord
FOR MAIN POWER TRANSFORMER SEE EXPLODED VIEW
15
1500 Array Subwoofer

16
1500 Array Subwoofer

17
1500 Array Subwoofer

18
1500 Array Subwoofer

19
1500 Array Subwoofer