jcb 19C-1E User manual

19C-1E
QUICK REFERENCE GUIDE
This Quick Reference Guide DOES NOT replace the Operators
Manual. You MUST read ALL the disclaimers and safety and other
instructions in the Operators Manual before initially operating this
product. Accordingly, no legal claims can be entertained based on
the data, illustrations or descriptions in this Quick Reference Guide.
Access additional information
www.servicepro.jcb.com
Instrument Panel
Start Up Sequence
Static Dimensions
Tie Down Points
Cab and Switch Panel
A. Track controls
B. Control Lever
C. Track extension lever
D. Dozer blade control lever
E. Ignition Switch
F. Motor running indicator light
G. Rotary hand throttle control
H. Instrument panel
J. Console switch panel
K. Auxiliary power socket
L. Fire extinguisher
M. Operator seat
N. Control isolation lever
O. Charging cable stowage
P. Quickhitch release bar
stowage
Cab
Switch Panel
A. Front undercarriage track leg tie-down points
B. Rear undercarriage track leg tie-down points
C. Angle = 25º to 45º
D. Angle = 9º to 15º
E. Length = 8’ 2”
F. Length = 5’ 8” to 3’ 4”
G. Length = 8’ 2”
H. Slew ring center line
J. Tie down decal
A. Control Isolation Switch (2Go)
B. Aux 1 selection switch
C. Lift overload on/off switch
D. Work lights on/off switch
E. Wipers/washer on/off switch
F. Auto-hydraulic warming switch (not used)
G. H+ mode selection switch (not used)
H. Aux 2 selection switch
J. Auto idle on/off switch (not used)
K. Beacon on/off switch
L. Q-hitch sequence
A. Battery Level
indicator gauge
B. Warning and
indicator lamps
Lifting Points
A. Boom Lift Point
B. Dozer Blade Lift Point
C. Spreader Bar
D. Centre of Gravity
E. 2’ 8”
F. 2’ 7”
G. 1’ 9”
Revision 1.0
1/11/2021

Service Points and Access Covers
Charging Levels & Charging
Hydraulic Hitch Unlock Sequence
Mechanical Hitch Unlock Sequence
Joystick & Dozer Lever Auxiliary Venting (Within 1 Minute of Motor Shutdown)
Swing Controls
A. Swing Left
B. Swing Right
C. Swing Thumb Wheel
Control
D. Change over button
Auxiliary Controls
A. Tilt/grab changeover for tilt-rotator
B. Boom swing/Aux change over button
C. Thumb –wheel control –Aux 2 (Low flow)
D. Continuous flow button –Hammer circuit
E. Thumb and wheel control –Aux 1 (High flow)
Note: A & D located underside of the joystick
Dozer Lever
A. Lower the dozer
B. Raise the dozer
C. Control lever
D. 2-speed selection
Retracting Undercarriage Lever
A. Track Extension Lever
B. Upward –Retract
C. Downward - Extend
A. Lock
B. Service compartment cover
C. Handle
A. Grease gun
B. Service disconnect
C. Fuse/relay box
D. 12V Battery
A. Hydraulic compartment cover
B. Lock
A. Hydraulic tank filler cap
B. High voltage batteries charging
point
C. Hydraulic oil level indicator
A. Full Charge
B. Low Battery
A. Charge indicator
B. Operating status
C. Charging socket
D. Charge cable
1. Connect charge lead to mains supply outlet and the
machine inlet.
2. Depress the reset button with the RCD*
3. Green status LED light will illuminate at charge inlet (A)
1. LED light will pulse when charging
2. LED light will hold green when plugged in and
not charging
4. Machine instrument panel will illuminate and display state
of charge
*for 230V AC mains supply, when using 110V AC, an RCD is not
provided
Excavator Levers (SAE)
A. Slew cab left
B. Slew cab right
C. Raise boom
D. Lower boom
E. Dipper in
F. Dipper out
G. Crowd bucket
H. Dump bucket
Hydraulic Compartment
Battery Compartment
Battery Cover
Hydraulic Compartment Cover