JCM Technologies GSM-CARD User manual

EN
communications card
user’s manual
jcmtechnologies
GSM-CARD/VGSM-CARD

Safety instructions 3
Introduction 4
General description 4
Introduction 6
Assembly 6
Configuration 7
Verification 8
LED indicators 8
Solving problems 10
FAQs 10
Technical data 11
Electrical parameters 11
Physical parameters 11
Radiofrequency parameters 11
Using the system 12
EC declaration of conformity 12
2 - jcmtechnologies
GSM-CARD / VGSM-CARD
Contents

GSM-CARD / VGSM-CARD
jcmtechnologies - 3
Safety instructions
In compliance with the European Directive low-voltage electrical equipment,
we hereby inform users of the following requirements:
• Disconnect the device from the power supply before handling.
• For units which are permanently connected, an easily accessible
circuit-breaker device must be built into the wiring system.
• This system should only be installed by qualified personnel with suitable
experience of automatic garage doors and knowledge of applicable
European regulations.
• The instruction manual for this unit must always remain in the possession
of the user.

GOOD
POOR
COVERAGE
STAT TX
BAD
OK
ALARM
ERROR
GSM-CARD / VGSM-CARD
Connected to an ACCESS-5K access control, it allows remote management of users.
Connected to a VERSUS control panel, it allows remote configuration of parameters and alarms.
GSM communication card for real-time management
General description
LED STATUS
INDICATORS
GSM
COVERAGE
LED
INDICATORS
CONNECTOR
TO MAIN
BOARD
SMA CONNECTOR
FOR GSM
ANTENNA
LED GS,
TRANSMISSION
INDICATORS
4 - jcmtechnologies
Introduction

GOOD
POOR
COVERAGE
STAT TX
BAD
OK
ALARM
ERROR
GSM-CARD / VGSM-CARD
Introduction
Back view
General description
SIM CARD
SLOT
MICRO-SD
MEMORY
CARD SLOT
(only Versus)
jcmtechnologies - 5

CONNECTION TO MAIN PCB
With the power supply disconnected,
insert the card into the device
GSM ANTENNA
Screw the GSM ANTENNA
supplied into the SMA
connector
GSM-CARD / VGSM-CARD
ACCESS-5K
installation
Installation
Assembly
6 - jcmtechnologies
GOOD
POOR
COVERAGE
STAT TX
BAD
OK
ALARM
ERROR
COMMS. CARD
VERSUS
installation
EXPANSION CARD

GSM-CARD / VGSM-CARD
Configuration
jcmtechnologies - 7
To change the default options,
you must install the SoftAssistant
program for Windows
GSM-CARD
For more information, visit:
https://www.jcm-tech.com/JCM/motion-programmers/
VGSM-CARD
To configure the device, please
access the following website:
http://versuscloud.jcm-tech.com/

GSM-CARD / VGSM-CARD
Verification
LED indicators
8 - jcmtechnologies
LEDs GSM
GOOD Good coverage.
Optimum data transfer
POOR Weak coverage, but sufficient for data transfer
BAD
Unstable coverage or no connection.
We recommend you not use the device in
this status, as there may be errors
COMMUNICATION LEDS
TX Lit during data transmission
When led indicator is bad, it is recommended to use a 3 meters long GSM antenna
extension cable
GOOD
POOR
COVERAGE
BAD
OK
ALARM
ERROR
GOOD
POOR
COVERAGE
STAT TX
BAD
OK
ALARM
ERROR

GSM-CARD
jcmtechnologies - 9jcmtechnologies - 9
ERROR LED
Number of flashes Error type Action required
1Module initialisation Wait for the initialization to be completed
2SIM card not detected Check SIM card insertion
3Incorrect PIN Modify communication settings in SoftAssistant
4SIM card locked Unlock SIM card (for example, with a free mobile)
5No communication Review GSM antenna connection (see GSM leds)
6Adjustments not valid Check Unique Key and APN in SoftAssistant
7Server not detected Contact M2M service provider
Operation LEDs
OK System working correctly (flashing=in process)
ALARM Use of backup GSM frequency (850 MHz)
ERROR System error
GSM-CARD / VGSM-CARD
Verification
LED indicators
If the GSM-CARD uses the backup frequency, it can interfere with the Motion transmitters
GOOD
POOR
COVERAGE
BAD
OK
ALARM
ERROR

Solving problems
GSM-CARD / VGSM-CARD
10 - jcmtechnologies
FAQs
Q: Can I use the supplied SIM to surf in Internet with a smartphone?
A: No, the SIM card is type M2M (Machine to Machine), therefore it only connects the main equipment to a private
server.
Q: Can I use any SIM card, for example the one I have on my phone?
A: No you cannot. It only works with bidirectional M2M SIMs from approved operators and specifically configurated.
Q: With the serial number that appears on the label, can you access your computer through any SoftAssistant?
A: No, you cannot. In addition to the serial number, it is also required the unique key to connect remotely.
Q: If I have the main equipment installed, will it work remotely only by plugging in a GSM-CARD?
A: Yes, the card is configured by default with the communication parameters of the approved operator.

Electrical parameters
Power supply 12V dc
Standby / Op. consumption <500 mA
Maximum power absorbed 6W
Operating temperature -20ºC … +55ºC
Size (without antenna) 77 x 52 x 10 mm
Physical parameters
Operating temperature -20ºC … +55ºC
Size (without antenna) 77 x 52 x 10 mm
Radiofrequency parameters
Radiated power EGSM 850 / 900 / 1800 / 1900 MHz
GSM-CARD / VGSM-CARD
Technical details
11 - jcmtechnologies

12 - jcmtechnologies
JCM TECHNOLOGIES, S.A. declares that the GSM-CARD/VGSM-CARD
complies with the applicable provisions of the section 3 of the R&TTE 2014/35/
CEE Directive and complies the fundamental requirements of the 2014/30/
EU Directive on electromagnetic compatibility and 2006/95/EC on low volta-
ge, insofar as the product is used correctly.
Visit www.jcm-tech.com
UM_3200706_GSM-CARD_VGSM-CARD_EN_Rev04
EC declaration of conformity
GSM-CARD / VGSM-CARD
Using the system
This device is designed for the use with automatic garage doors.
It is not guaranteed for directly activating equipment other than that specified.
The manufacturer reserves the right to modify equipment specifications
without prior notice.