Jenn-Air JES8850BAF User manual

JENN-AIR _ ELECTRIC SMOOTHTOP
SLIDE-IN RANGE
TABLE OF CONTENTS
Important Safety Instructions .....................................1-3
Care & Cleaning ..............................................................4-6
Maintenance .....................................................................6-7
Troubleshooting ..............................................................8-9
Surface Cooking .........................................................10-12
Oven Cooking ..............................................................13-20
Options ..........................................................................21-25
Favorites ...............................................................................26
Setup ..............................................................................27-29
Accessories .........................................................................30
Warranty & Service ...........................................................31
Guide d'utilisation et d'entretien .................................32
Guia de uso y cuidado ....................................................66
I JENN-AIR
Form No. A/11/05 Part No. 8113P520 00 @2005 Maytag Appliances Sales Co. Litho U.S.A.

or replace any part of your appliance unless it is
specifically recommended in this guide. All other
servicing should be referred to a qualified servicer.
Always disconnect power to appliance before servicing.
General instructions
MPORTANT SAFETY
NSTRU
Warning and important Safety instructions appearing in
this guide are not meant to cover all possible conditions
and situations that may occur. Common sense, caution,
and care must be exercised when installing,
maintaining, or operating the appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
To check if device is properly installed, look underneath
range with a flashlight to make sure one of the rear
leveling legs is properly engaged in the bracket slot. The
anti-tip device secures the rear leveling leg to the floor
when properly engaged. You should check this anytime
the range has been moved.
To Prevent Fire or Smoke
Damage
Be sure all packing materials are removed from the
appliance before operating it.
Keep area around appliance clear and free from
combustible materials. Flammable materials should not
be stored in an oven.
Many plastics are vulnerable to heat. Keep plastics away
from parts of the appliance that may become warm or
hot.
To prevent grease fires, do not let cooking grease or
other flammable materials accumulate in or near the
appliance.
Read and follow all instructions before using this
appliance to prevent the potential risk of fire, electric
shock, personal injury or damage to the appliance as a
result of improper usage of the appliance. Use appliance
only for its intended purpose as described in this guide.
To ensure proper and safe operation: Appliance
must be properly installed and grounded by a qualified
technician. Do not attempt to adjust, repair, service,
In Case of Fire
Turn off appliance and ventilating hood to avoid
spreading the flame. Extinguish flame, then turn on
hood to remove smoke and odor.
*Cooktop: Smother fire or flame in a pan with a lid or
cookie sheet.
,, NEVER pick up or move a flaming pan.

* Oven: Smother fire or flame by closing the oven door.
Do not use water on grease fires. Use baking soda, a
dry chemical or foam-type extinguisher to smother fire
or flame.
Child Safety
NEVER leave children alone or unsupervised near the
appliance when it is in use or is still hot. Children
should never be allowed to sit or stand on any part of
the appliance as they could be injured or burned.
Children must be taught that the appliance and utensils
in it can be hot. Let hot utensils cool in a safe place, out
of reach of small children. Children should be taught
that an appliance is not a toy. Children should not be
allowed to play with controls or other parts of the
appliance.
About Your Appliance
To prevent potential hazard to the user and damage to
the appliance, do not use appliance as a space heater to
heat or warm a room. Also, do not use the oven as a
storage area for food or cooking utensils.
Do not obstruct the flow of air by blocking the oven vent.
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
SURFACES OF OVEN. Heating elements may be hot even
though they are dark in color. Interior surfaces of any
oven become hot enough to cause burns. During and
after use, do not touch, or let clothing or other flam-
mable materials contact heating elements or interior
surfaces of oven until they have had sufficient time to
cool. Other surfaces of the appliance may become hot
enough to cause burns - among these surfaces are: oven
vent opening and surface near this opening, oven door
and window of oven door.
Do not touch a hot oven light bulb with a damp cloth as
the bulb could break. Should the bulb break, disconnect
power to the appliance before removing bulb to avoid
electrical shock.
NEVER use aluminum foil to cover an oven rack or oven
bottom. Misuse could result in risk of electric shock, fire,
or damage to the appliance. Use foil only as directed in
this guide.
Cooking Safety
Never heat an unopened food container in the oven.
Pressure build-up may cause container to burst
resulting in serious personal injury or damage to the
appliance.
Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes
should never be used as potholders because they can
trail across hot elements and ignite or get caught on
appliance parts.
Wear proper apparel. Loose fitting or long hanging-
sleeved apparel should not be worn while cooking.
Clothing may ignite and cause burns if garment comes
in contact with heating elements.
Always place oven racks in the desired positions while
oven is cool. Slide oven rack out to add or remove food,
using dry, sturdy potholders. Always avoid reaching into
the oven to add or remove food. If a rack must be
moved while hot, use a dry potholder. Do not let
potholder contact hot element in oven.
Use racks only in the oven in which they were shipped/
purchased.
Use care when opening the oven door. Let hot air or
steam escape before removing or replacing food.
PREPARED FOOD WARNING: Follow food
manufacturer's instructions. If a plastic frozen food
container and/or its cover distorts, warps, or is otherwise
damaged during cooking, immediately discard the food
and its container. The food could be contaminated.
Do not allow aluminum foil or meat probe to contact
heating element.
Always turn off all controls when cooking is completed.
Utensil Safety
Follow the manufacturer's directions when using oven
cooking bags.
This appliance has been tested for safe performance
using conventional cookware. Do not use any devices
or accessories that are not specifically recommended in
this guide. Do not use add-on oven convection systems.
The use of devices or accessories that are not expressly
recommended in this guide can create serious safety
hazards, result in performance problems, and reduce the
life of the components of the appliance.

If pan is smaller than element, a portion of the element
will be exposed to direct contact and could ignite
clothing or potholder.
Only certain types of glass, glass/ceramic, ceramic,
earthenware, or other glazed utensils are suitable for
cooktop or oven service without breaking due to the
sudden change in temperature. Follow utensil
manufacturer's instructions when using glass.
Turn pan handle toward center of cooktop, not out into
the room or over another surface element. This reduces
the risk of burns, ignition of flammable materials, or
spillage if pan is accidently bumped or reached by small
children.
Cooktop
NEVER leave surface units unattended, especially when
using high heat. An unattended boilover could cause
smoking and a greasy spillover can cause a fire.
This appliance is equipped with different size surface
elements. Select pans with flat bottoms large enough to
cover element. Fitting pan size to element will improve
cooking efficiency.
GLASS-CERAMIC SURFACE: NEVER cook on broken
cooktop. If cooktop should break, cleaning solutions and
spillovers may penetrate the broken cooktop and create
a risk of electric shock. Contact a qualified technician
immediately.
Deep Fat Fryers
Use extreme caution when moving the grease pan or
disposing of hot grease. Allow grease to cool before
attempting to move pan.
Ventilating Hoods
Clean range hood and filters frequently to prevent grease
or other flammable materials from accumulating on hood
or filter and to avoid grease fires.
When flaming foods under the hood, turn the fan on.
Cleaning Safety
Clean cooktop with caution. Turn off all controls and
wait for appliance parts to cool before touching or
cleaning. Use care to avoid steam burns if a wet sponge
or cloth is used to wipe spills on a hot surface. Some
cleaners can produce noxious fumes if applied to a hot
surface.
Clean only parts listed in this guide.
Self-Clean Oven
Do not clean door gasket. The door gasket is essential
for a good seal. Care should be taken not to rub,
damage, or move the gasket.
Do not use oven cleaners or oven liners of any kind in or
around any part of the self-clean oven.
important Safety Notice
and Warning
The California Safe Drinking Water and Toxic
Enforcement Act of 1986 (Proposition 65) requires the
Governor of California to publish a list of substances
known to the State of California to cause cancer or
reproductive harm, and requires businesses to warn
customers of potential exposures to such substances.
Users of this appliance are hereby warned that when the
oven is engaged in the self-clean cycle, there may be
some low-level exposure to some of the listed
substances, including carbon monoxide. Exposure to
these substances can be minimized by properly venting
the oven to the outdoors by opening the windows and/or
door in the room where the appliance is located during
the self-clean cycle.
IMPORTANT NOTICE REGARDING PET BIRDS: Never
keep pet birds in the kitchen or in rooms where the
fumes from the kitchen could reach. Birds have a very
sensitive respiratory system. Fumes released during an
oven self-cleaning cycle may be harmful or fatal to birds.
Fumes released due to overheated cooking oil, fat,
margarine and overheated non-stick cookware may be
equally harmful.
Save These instructions for Future Reference
3

CARE CLEANING
Self-Clean Oven To
1.
2.
3.
set Self=Clean: _,.............
Clean \
Press Clean pad. ,
............ /
REMOVE RACKSwill be displayed. Remove the racks.
Select CONTINUE using the Quickset pad. The Quickset
pads are located on either side of the control panel
display.
Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior.
The oven should be cleaned regularly by wiping up spillovers
to prevent excessive smoke and flare-ups. Do not allow a
heavy build-up of soil to accumulate in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Before Self-Cleaning
1. Turn off the oven light before cleaning. The oven light may
burn out during the clean cycle.
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks will discolor and may not slide
easily after a self-clean cycle ifthey are not removed.
3. Clean oven frame, door frame, area _ 7_T_F-]
outside of gasket, and around the \
opening in the door gasket with a
nonabrasive cleaner such as Bon
Ami* or detergent and water. The
self-cleaning process does
not clean these areas. They should
be cleaned to prevent soil from baking on during the clean
cycle. 0-he gasket is the seal around the oven door and
window.)
4. To prevent damage, de net clean or rub the gasket around
the oven door. The gasket is designed to seal in heat
during the clean cycle.
5. Wipe up excess grease or spill-overs from the oven
bottom. This prevents excessive smoking, flare-ups or
flaming during the clean cycle.
6. Wipe up sugary and acidic spillovers such as sweet
potatoes, tomato, or milk-based sauces. Porcelain enamel
is acid-resistant, not acid-proof. The porcelain finish may
discolor if acidic or sugary spills are not wiped up before a
self-clean cycle.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. CLEAN, TIME, LOCKED and the cleaning time countdown
will be displayed while the oven is cleaning. OVEN
COOLING will appear in the display when the cleaning
time has been completed and the oven is still locked.
Important: The door lock will disengage approximately one
hour after the cleaning time is completed. OVEN COOLING
will go off in the display when the oven door has unlocked.
To Delay a Self=Clean Cycle:
/............... \
1. Press Clean pad. Clean
2. REMOVE RACKSwill be displayed.
Removethe racks.
3. Select CONTINUE using the Quickset pad.
4. Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. The door will lock. CLEAN,TIME, LOCKED and the
cleaning time countdown will be displayed
6. After door locks, press the Mere Options pad.
7. Select BELAY using the Quickset pad.
8. Select the number of hours you want to delay the start of the
self-clean cycle. Cent.
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
4

9. The delay time and cleaning time will be displayed.
After Self=Cleaning
About one hour after the end of the clean cycle, the lock
will disengage and OVEN COOLING will go off in the
display. At this point, the door can he opened.
Some soil may leave a light gray, powdery ash which can be
removed with a damp cloth. If soil remains, it indicates that
the clean cycle was not long enough. The soil will be removed
during the next clean cycle.
If the oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and embossed rack
supports with a small amount of vegetable oil to restore ease
of movement.
A white discoloration may appear after cleaning if acidic or
sugary foods were not wiped up before the clean cycle. This is
normal and will NOT affect performance.
Cleaning Procedures
Notes:
• If the oven door is left open, CLOSEDOORwill appear in
the display until the door is closed.
• If more than 30 seconds elapse between pressing the
Clean pad and pressing a number pad, the program will
automatically return to the previous display.
, The oven door will be damaged if it is forced to open
during cleaning or cooling process.
• The first few times the oven is cleaned, some smoke and
odor may be detected. This is normal and will lessen or
disappear with use. If the oven is heavily soiled, or if the
broiler pan was accidently left in the oven, excessive
smoke and odor may occur.
• As the oven heats and cools, you may hear sounds of
metal parts expanding and contracting. This is normal
and will not damage your appliance.
* Brand names are registered trademarks of the
respective manufacturers.
** To order call 1-800-JENNAIR (1-800-536-6247].
Control Panel
Control Knobs
Cooktop -
Glass=Ceramic
, To activate control lock for cleaning, see Locking the Control,page 14.
, Wipe with damp cloth. Dry thoroughly.
,Glasscleaners may be used if sprayed on a cloth first. DO NOTspray directly on controlpads and
display area.
, Do not useother cleaning sprays,abrasive cleaners or large amounts of water on the panel.
°Removeknobs in the OFFposition by pulling forward.
• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.
, Turn on each element to be sure the knobs have been correctly replaced.
Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia.
important: Call an authorized senficer ff the glass-ceramic top should crack, break or if metal or
aluminum foil should melt on the cooktop.
• Allow the cooktop to cool before cleaning.
•General - Clean cooktop after each use, or when needed, with a damp paper towel and Cooktop Cleaning
Creme* (Part No. 20000001)**.Then buff with a clean, dry cloth.
Important: Permanentstains will develop if soil is allowed to cook on by repeatedly usingthe cooktop when
soiled.
, Heavy Soils or Metal Marks - Dampen a "scratchless" or "never scratch" scrubber sponge. Apply
Cooktop Cleaning Creme* and scrub to remove as much soil as possible. Apply a thin layer of the creme over
the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3 hours for very heaw soil]. Keep
moist by covering the paper towel with plastic wrap. Scrub again, then buff with a clean, dry cloth.
important: Onlyuse a CLEAN,DAMP "scratchless"pad that issafe for non-stick cookware. Thepattern and
glass willbe damaged ff thepad is not damp, if thepad is soiled, or if another type ofpad is used.
• Burned-on or Crusty Soils - Scrub with a "scratchless" or "never scratch" scouring pad and
Cooktop Cleaning Creme*.
Important: Hold a razor blade scraper at 30°angle and scrape anyremaining soil Then,dean as described
above.Do not use the razor blade for daily cleaningasit may wearthe pattern on the glass. /
Melted Sugar or Plastic - Immediately turn element to LOW and scrape sugar or plastic
from hot surface to a cool area. Then turn element OFF and allow to cool. Clean residue
with razor blade scraper and Cooktop Cleaning Creme*.
5

•Avoidusingexcessiveamountsofwaterwhichmayseepunderorbehindglass,causingstaining.
Oven Window
and Door =
Glass • Wash with soap and water. Rinsewith clear water and dry. Glass cleaner can be used if sprayed on a cloth first.
° Do not use abrasive materials such asscouring pads, steel wool or powdered cleaners as they will
scratch glass.
Oven Interior • Follow instructionson pages 4-5 to set a self-clean cycle.
Oven Racks
Stainless Steel
(select models}
° Clean with soapy water.
• Removestubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.
• Rackswill permanently discolor and may not slide smoothly if left in the oven during a self-clean operation.
If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease
of movement, then wipe off excessoil.
• DO NOT USEANY CLEANING PRODUCT CONTAiNiNG CHLORINE BLEACH.
• DO NOT USEABRASIVE OR ORANGE CLEANERS.
•ALWAYS WiPE WiTH THE GRAIN WHEN CLEANING.
• Daily Cleaning/Light Soil -- Wipe with one of the following - soapy water, white vinegar/water solution,
Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse
and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.
20000008}**.
° Moderate/Heavy Soil -- Wipe with one of the following -Bon Ami, Smart Cleanser, or Soft Scrub* -
using a damp sponge or soft cloth. Rinseand dry. Stubborn soils may be removed with a damp multi-
purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks,
follow with Stainless Steel Magic Spray*.
• Discoloration -- Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*.Rinse
immediately and dry. To remove streaks and restore luster, follow with StainlessSteel Magic Spray*.
Storage • When cool, wash with warm, soapy water, rinse and dry. Never wipe a warm or hot surface with a damp
Drawer (select cloth as this may damage the surface and may cause a steam burn.
models} - • Forstubborn soil, use mildly abrasive cleaning agents such as baking soda paste or Bon Ami.* Do not use
Painted abrasive, caustic or harsh cleaning agents such as steel wool pads or oven cleaners. These products will
Enamel scratch or permanently damage the surface.
important: Use adry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may
discolor or dull if soil is not immediately removed. Thisis especially important for white surfaces.
AINTENANCE
Oven Door
°NEVER attempt to open or close door or operate oven until
door is properly replaced.
• NEVER place fingers between hinge and front oven frame.
Hinge arms are spring mounted. If accidentally hit, the
hinge will slam shut against oven frame and could injure
your fingers. 6
To remove:
1. When cool, open the oven door
to the broil stop position
(opened about four inches}.
2. Grasp door at each side. Do not
use the door handle to lift door.
3. Lift up evenly until door clears
hinge arms.
To replace:
1. Grasp door at each side.
2. Align slots in the door with the hinge arms on the range.
Cont.

3. Slide the door down onto the hinge arms until the door is
completely seated on the hinges. Pushdown on the top
corners of the door to completely seat door on hinges.
Door should not appear crooked.
Important: The oven door on a new range may feel "spongy"
when it is closed. This is normal and will decrease with use.
Oven Light
Oven Window
To protect the oven door window:
1. Do not use abrasive cleaning agents such as steel wool
scouring pads or powdered cleansers as they may scratch
the glass.
2. Be not hit the glass with pots, pans, furniture, toys, or
other objects.
3. Be not close the oven door until the oven racks are in
place.
Scratching, hitting, jarring or stressing the glass may weaken
its structure causing an increased risk of breakage at a later
date.
Leveling Legs
To assure the proper replacement bulb is used, order bulb
from Jenn-Air. Call 1-800-JENNAIR C1-800-536-6247], ask for
part number 74004458 - halogen bulb.
To Replace Oven Light Bulb:
1. Disconnect power to the oven.
2. When oven is cool, use fingertips to grasp edge of bulb
cover. Pull out and remove.
3. Carefully remove old bulb by pulling straight out of
ceramic base.
4. To avoid damaging or decreasing the life of the new bulb,
do not touch the bulb with bare hands or fingers. Hold
with a dry cloth or paper towel. Push new bulb prongs
straight into small holes of ceramic base.
5. Replace bulb cover by snapping into place.
6. Reconnect power to the oven. Reset clock.
Storage [}rawer (select models)
Be sure the range is leveled when installed. If
the range is not level, turn the leveling legs, /_
located at each corner of the range, until range
is level.
NTI RACKET
\LEVELING LEG
The storage drawer can be removed to allow you to clean
under the range.
To remove:
1. Empty drawer and pull out to the first stop position.
2. Lift up the front of the drawer.
3. Pull out to the second stop position.
4. Grasp sides and lift drawer up and out.
To replace:
1. Fit the ends of the drawer glides into the rails in the range.
2. Lift up the front of the drawer and gently push in to the
first stop position.
3. Lift drawer up again and push until drawer is closed.

TRt UBLE NG
For most concerns, try these first.
Part or ai{ of appliance does
not work.
Clock, indicator words, and/or
lights operate but oven does
not heat.
Baking results are not as
expected or differ from
previous oven.
Food is not broiling properly or
smokes excessively.
Oven wiil not self=clean.
Oven did not clean properly.
Oven door will not unlock after
self=clean cycle.
There are no beeps and
no display.
•Check if oven controls have been properly set.
• Check to be sure plug is securely inserted into receptacle.
• Check or re-set circuit breaker. Check or replace fuse.
• Check power supply.
° Check if surface and/or oven controls have been properly set.See pgs. 10-11 & 15.
• Check if oven door is unlocked after self-clean cycle. See pg. 4.
° Check if oven is set for a delayed cook or clean program. See pgs. 15& 4.
• Check if Control Lock is activated. See pg. 14.
• Check if control is in Sabbath Mode. See pg. 28.
° Oven may be set for a Cook & Hold or delay function.
° Control Lock may have been set. See pg. 14.
o
o
o
Make sure the oven vent has not been blocked. See pg. 20 for location.
Check to make sure range is level.
Temperatures often vary between a new oven and an old one.As ovens age, the oven
temperature often "drifts" and may become hotter or cooler. Seepg. 28 for
instructions on adjusting the oven temperature. Important: It is not recommended
to adjust the temperature if only one or two recipes are in question.
• Check oven rack positions. Food may be too close to element.
• Broil element was not preheated.
• Aluminum foil was incorrectly used. Never line the broiler insert with foil.
• Ovendoor was closed during broiling. Leavethe door open to the first stop position
(about 4 inches:).
• Trim excess fat from meat before broiling.
° A soiled broiler pan was used.
° Voltage in house may be low.
• Check to make sure the cycle is not set for a delayed start. See pg. 4.
• Check if door is closed.
• Check if control is in Sabbath Mode. See pg. 28.
° Oven may be over 400° F.Oven temperature must be below 400° Fto program a
clean cycle.
•Longercleaning time may be needed.
•Excessivespillovers, especially sugary and/or acidic foods, were not removed prior
to the self-clean cycle.
° Oven interior isstill hot. Allow about one hour for the oven to cool after the
completion of a self-clean cycle. The door can be opened when the LOCK indicator
word is not displayed.
• The control and door may be locked. See pg. 14.
°Oven may be in Sabbath Mode. See page 28.
8

Smoothtop surface
shows wear=
Moisture collects on oven
window or steam comes from
oven vent=
There is astrong odor or light
smoke when oven is turned on.
1.Tiny scratches or abrasions.
• Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans
across top. Make sure pan bottom is not rough. Usethe recommended cleaning
agents. See page 5.
2.Metal marks.
•Be not slide metal pans across top. When cool, clean with Cooktop Cleaning Creme.
See page 5.
3.Brown streaks and specks.
°Removespills promptly. Never wipe with a soiled cloth or sponge. Make sure cooktop
and pan bottom are clean.
4.Areas with a metallic sheen.
°Mineral deposits from water and food. Use recommended cleaning agents. See page 5.
5.Pitting or flaking.
• Removesugary boilovers promptly. See page 5.
° Thisis normal when cooking foods high in moisture.
°Excessivemoisture was usedwhen cleaning the window.
•Thisis normal for a new range and will disappear after a few uses. Initiating a clean
cycle will "burn off" the odors more quickly.
°Turning on a ventilation fan will help remove the smoke and/or odor.
°Excessivefood soils on the oven bottom. Usea self-clean cycle.
Cooktop does not get • Surface controls may not be set properly.
hot enough. • Voltage to house may be low.
Fault Codes °
Noises may be heard.
The oven may detect a fault during programming or during operation. If a fault is
detected, the message FAULT DETECTED- PRESSPOWERTO CLEARor FAULT
DETECTED- PRESSENTERTOTRY AGAIN may appear. Follow directions in the display.
If the fault reappears or does not clear, call an authorized servicer or the toll-free number
in the display.
If the same operation is attempted before having the oven repaired, the message
FEATURENOTAVAILABLE will appear. The feature will remain inoperable until service
is obtained.
If the oven is heavily soiled, excessivefiareups may result in a fault code during cleaning.
Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then
reset the clean cycle. If the fault code reappears, contact an authorized servicer.
°The oven makes several low-level noises.You may hear the oven relays as they go on
and off. This is normal.
• As the oven heats and cools, you may hear sounds of metal parts expanding and
contracting. This is normal and will not damage your appliance.
SAb flashing and then °Oven isin Sabbath Mode. To cancel, press and hold the Setup pad for five
displayed continuously, seconds.
Cannot add another Favorite. • Favorites is full. To delete a favorite and add another, see page 26.
• Brand names for cleaning products are registered trademarks of the respective manufacturers.
•* To order direct, call 1-800-JENNAIR (1-800-536-6247).

URFACECOOK=NG
Surface Controls
Use to turn on the surface elements. An infinitechoice of
heat settings isavailable from Lowto High. The knobscan
be set on or between any of the settings.
Setting the Controls
1. Place pan on surface element.
2. Push in and turn the knob in either direction to the desired
heat setting•
Triple Element (selectmodels)
The cooking surface has one triple
element located in the right front
position. This element can be used for
larger cooking utensils when the triple
element is used, or for smaller pans
when the single or dual settings are
chosen. To select single, dual or triple
settings, rotate the element selection knob.
• The control panel is marked to identify which //
element the knob controls. For example, the _q...._Front
graphic at right indicates right front element.
3. There is an element indicator light on the control panel.
When any surface control knob isturned on, the light will
turn on. The light will turn off when all the surface
elements are turned off.
When a control is turned on, a glow can be seen through
the smoothtop surface. The element will cycle on and off
to maintain the preset heat setting, even on High.
4. After cooking, turn knob to OFF. Remove pan.
Dual Element (select models)
The cooking surface is equipped with a
dual element located in the left front
position. To operate, push in on the
control knob and turn to the rightto
control the small element, or push in
and turn to the/eft to control the large
element.
Custom Control (select models_
The Custom Control Dual Element offers
two element sizes and islocated in the
left front position• This element uses an
electronic sensor to constantly monitor
and adjust heat output for precise and
consistent temperature control•
Flex-Choice TM Element (select models)
The Flex-ChoiceTM element is fully
• • • 'xx,
funct=onmg element that prowdes an ultra
• . ,-,
low Melt heat sett=ngfor melt=ng
chocolate and butter. It islocated in the
right rear position.
• .
The Melt setting uslocated between
3 and OFF.Heat settings outside of this
area function as a normal element, with 3
(Low) to High settings.
Important: When using the normal settings for preparing
foods, it may take a few minutes for the cooking area to cool
to the Melt heat setting.
10

Warming Zone (select models)
Use the Warming Zone to keep cooked foods warm, such as
vegetables and gravies.
Press the Warm Zone pad to turn on the Warm
element, then press the Quickset pad for Zone
HIGH or LOW. To turn off, press the Warm ....., On /Off
Zone pad once. An icon may light as a reminder" ............
that the Warming Zone isin use.
Important:
• Never warm food for longer than one hour (eggs for
30 minutes), as food quality may deteriorate.
• Do not heat cold food on the Warming Zone.
• Heat settings will vary depending on type and amount of
food. Always hold food at proper food temperatures. USDA
recommends food temperatures between 140°-170° F.
Notes:
Use only cookware and dishes recommended as safe for
oven and cooktop use.
Always use oven mitts when removing food from the
Warming Center as cookware and plates will be hot.
All foods should be covered with a lid or aluminum foil to
maintain food quality.
When warming pastries and breads the cover should have
an opening to allow moisture to escape.
Do not use plastic wrap to cover foods. Plastic may melt
on to the surface and be very difficult to clean.
Suggested Heat Settings
The size, type of cookware and cooking operation will affect
the heat setting.
High (9): Use to bring
liquid to a boil. Always
reduce setting to a lower
heat when liquids begin to
boil or foods begin to cook.
L.
Low (1): Use to keep
foods warm and melt
chocolate and butter.
iVied. Low (3):
Use to
continue
cooking
covered foods
or steam foods.
IVied. High (7): Use to
brown meat, heat oil for
deep fat frying or
sauteing. Maintain fast
boil for large amounts
of liquids,
Lf edium (5): Use to
maintain slow boil for
large amounts of liquids
and for most frying
operations.
Smoothtop Surface
Notes:
° Cooktop may emit light smoke and odor the first few
times the cooktop is used. This is normal.
° Smoothtop cooktops retain heat for a period of time
after the element is turned off. Turn the elements off
a few minutes before food iscompletely cooked and use
the retained heat to complete cooking. When the hot
surface light turns off, the cooking area will be cool
enough to touch. Because of the way they retain heat, the
smoothtop elements will not respond to changes in
settings as quickly as coil elements.
• In the event of a potential boilover, remove the pan from
the cooking surface.
•Never attempt to lift the cooktop.
• The smoothtop surface may appear discolored when it is
hot. This is normal and will disappear when the surface
cools.
Hot Surface Indicator Lights
The Hot Surface indicator lights are located next to the
elements. These lights indicatewhen the adjacent cooking
area ishot to the touch even after the control has been
turned off. The red light will remain on until the surface
has cooled.
Cooking Areas
The cooking areas on your range are identified by permanent
patterns on the smoothtop surface. For most efficient cooking,
fit the pan size to the element size.
Pans should not extend more than 1/2to 1-inch beyond
the cooking area.
When a control is turned on, a glow can be seen through the
smoothtop surface. The element will cycle on and off to
maintain the preset heat setting, even on High.
Formore informationon cookware, refer to Cookware
Recommendations on page 12.
REGULAR
DUAL ELEMEN_
(SELECT MODELS)
WARMING ZONE FL EXCHOICE 7M
ELEMENT
(SELECT
MODELS)
TRIPLE ELEMENT
(SELECT MODELS)
Tips to Protect the
Smoothtop Surface
Cleaning (see page 5 for more information)
°Before first use, clean the cooktop.
• Clean your cooktop daily or after each use. This will keep
your cooktop looking good and can prevent damage.
11

• If a spillover occurs while cooking, immediately clean the
spill from the cooking area while it is hot to prevent a tough
cleaning chore later. Using extreme care, wipe spill with a
clean, dry towel.
• Do not allow spills to remain on the cooking area or the
cooktop trim for a long period of time.
• Never use abrasive cleansing powders or scouring pads
which will scratch the cooktop.
• Never use chlorine bleach, ammonia or other cleansers not
specifically recommended for use on glass-ceramic.
To Prevent Marks & Scratches
• Do not use glass pans. They may scratch the surface.
• Never place a trivet or wok ring between the surface and
pan. These items can mark or etch the top.
° Do not slide aluminum pans across a hot surface. The pans
may leave marks which need to be removed promptly. (See
Cleaning, page 5.]
° Make sure the surface and the pan bottom are clean before
turning on to prevent scratches.
• To prevent scratching or damage to the glass-ceramic top,
do not leave sugar, salt or fats on the cooking area. Wipe
the cooktop surface with a clean cloth or paper towel
before using.
• Never slide heavy metal pans across the surface since
these may scratch.
To Prevent Stains
• Never use a soiled dish cloth or sponge to clean the
cooktop surface. A film will remain which may cause stains
on the cooking surface after the area is heated.
• Continuously cooking on a soiled surface may/will result in
a permanent stain.
To Prevent Other Damage
• Do not allow plastic, sugar or foods with high sugar
content to melt onto the hot cooktop. Should this happen,
clean immediately. (See Cleaning, page 5._
• Never let a pan boil dry as this will damage the surface and
pan.
° Never use cooktop as a work surface or cutting board.
• Never cook food directly on the surface.
• Do not use a small pan on a large element. Not only does
this waste energy, but it can also result in spillovers burning
onto the cooking area which requires extra cleaning.
• Do not use non-fiat specialty items that are oversized or
uneven such as round-bottom woks, rippled bottom and/or
oversized canners and griddles.
•Do not use foil or foil-type containers. Foil may melt onto
the glass. If metal melts on the cooktop, do not use. Call an
authorized servicer.
Cookware Recommendations
Using the right cookware can prevent many problems, such
as food taking longer to cook or achieving inconsistent
results. Proper pans will reduce cooking times, use less
energy, and cook food more evenly.
Flat Pan Tests
To determine whether your pans are flat.
The Ruler Test:
1. Placea ruler across tile bottom of tile pan.
2. Hold it up to the light.
3. Little or no light should be visible under the ruler.
The Bubble Test:
1. Put I inchof water in tile pan. Placeon cooktop and turn
control to High.
2. Watch the formation of the bubbles as the water heats.
Uniform bubbles mean good performance, and uneven
bubbles indicatehot spots and uneven cooking.
Flat,smooth-bottom Panswith grooved or warped bottoms.
_ans. Panswith uneven bottoms do not cook
efficiently and sometimes may not
boil liquid.
Heavy-gauge pans. Very thin-gauge metal or glass pans.
Pansthat are the Panssmaller or larger than the
same size asthe element by 1inch.
element.
Secure handles. Cookware with loose or broken handles.
Heavy handles that tilt the pan.
Tight-fitting lids. Loose-fitting lids.
Flat-bottom woks. Woks with a ring-stand bottom.
Canning and Oversize Cookware
All canners and large pots must have fiat bottoms and
must be made from heavy-gauge materials. This iscritical
on smoothtop surfaces. The base must not be more than
1inchlarger than the element.
When canners and pots do not meet these standards, cooking
times may be longer, and cooktops may be damaged.
Somecanners are designed with smaller bases for use on
smoothtop surfaces.
When canning, use the High heat setting only until the
water comes to a boil or pressure is reached in the canner.
Reduce to the lowest heat setting that maintains the boil or
pressure. If the heat is not turned down, the cooktop may be
damaged.
12

OVENCOOK=NG
Control Panel
AB CD
C!!_ "Favorites
On/Off
&etup
On/Off
Clean
Rapid More
-- Preheat i_s_
JKL
E
f
TIMER 1
On /Off
Warm Warm Oven
Zone Drawer Light CANCEL
On/Off On/Off
P- I I
Ni N 0 P
G H
_"""1
I
12 3
TIMER2 A_C DEF
On/Off 456
GHI JKL MNO
7 8 9
POR$ TUV WXYZ
Back 0 Enter
[ Sp_ce I
lack
Q
The control panel isdesigned for ease in programming. The display window shows options for each function and moves from step
to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake
operation.
i_i;;iHiiiill
i!!!i!i!:K!i_ii_i
iiiiliOill
!I!A!:I;;:
i!ii:ii_i;i!i!i;i_iiiiiiiiiiiiiiiii_ii
Rapid Preheat
(select models)
Convect
(select models)
Bake
Broil
TIMER 1
Display
TIMER 2
Number Pads
Favorites
More Options
Clean
Setup
Warm Zone
Warm Drawer
(select models)
Oven Light
CANCEL
Quickset pads
Use to decrease preheating time.
Usefor convection baking and roasting.
Usefor baking and roasting.
Usefor broiling and top browning.
Sets timer.
Displaysoven functions, options and
window time of day.
Sets timer.
Useto enter time and temperature,
or to enter Favorites names.
Useto access,program or save
baking cycles.
Useto access additional features.
Useto set self-clean cycle.
Useto view or change factory
default settings.
Useto turn Warming Zone on and off.
Useto operate the Warming Drawer.
Useto turn the oven light on or off.
Cancels all operations exceptTimer,
Clock, Favorites,Setup and Warm
Drawer.
Useto select options in display
window (next to display window
on both sides),
Quickset Pads
Quickset pads are located on each side of the display window
and are used to select the desired function or option in the
display window. To select the option or function, press the
Quickset pad next to the word.
If you need to back out of a function or option in the display,
press the Back pad. When your programming is complete,
press the Enter pad or wait four seconds and the function will
start automatically.
Up arrows indicate additional screens with additional options.
Press the Quickset pads next to the arrows to scroll through
the display.
Important: Four seconds after entering the function,
option, number or letter, the function will automatically be
entered. If more than 30 seconds elapse between steps in
programming, the function will be canceled and the
display will return to the previous display.
Clock
Setting the Clock: /.........................
1. Press the Setup pad. Setup '
',On/Off
2. Select CLOCK using the Quickset pads. "............ J
3. Select TINIE
4. Enter the time using the number pads.
5. Press Enter pad.
6. Select ANI or PlVl in 12 hour mode. (For 24 hour clock, see
page 14.)
7. To exit the Setup mode, press Setup pad.
13Cont.

Activating and canceling the clock/day
of week display:
1. Press Setup pad. Setup '
On/Off
2. Select CLOCK. /
3. Press the arrow to scroll until DISABLE isdisplayed.
4. Select DISABLE.
5. Select TIME.
6. Select OFF to turn the clock display off, or select ON to turn
the clock display on.
7. Select OFF to turn the day of the week display off. Select
ON to turn the weekday display on.
8. To exit the Setup mode, press Setup pad.
Entering the day of the week:
1. Press Setup pad. ,Setup
2. Select CLOCK. , On!off/
.......... /
3. Press the arrow to scroll until DAY isdisplayed.
4. Use Quickset arrow to scroll through the days.
5. Select day desired.
6. To exit the Setup mode, press Setup pad.
To set the clock for a 12 or 24 hour format:
The clock can be set to display time in either a 12 hour or 24
hour format.
1. Press the Setup pad. "Setup '
On/Off
2. Select CLOCK. '\ _"
3. Use the arrow to scroll to the next screen.
4. Select 12/24 HOUR.
5. Select 12 HB or 24 HR.
6. To exit Setup mode, press Setup pad.
Timers
Setting the Timers (Timer 1 or Timer 2):
1. Press TIMER 1 or TIMER 2 pad.
2. Press one of the displayed times using the
Quickset pads, or press the number pads to
enter the desired time. ....., On /Off ,/
Important: Each press of the displayed time choices adds
additional time. Forexample, pressing "10 MIN" three
times provides 30 minutes on the timer [0:30).
3. Press Enter pad.
Changing the amount of time entered once the
Timer starts:
/............
1. Press the TIMEB 1 orTIMEB2pad once. ;TIMER!
2. Press the displayed times on the Quickset ', On /Off//
pads repeatedly until the desired time is entered.
OR
3. Press the number pads to enter the new desired time.
4. Press Enter pad.
14
Canceling the Timer: .......
1. Press the TIMER 1 or TIMER 2 pad twice. /:[IMERi'L
If both Timers are active: "
If the desired Timer is already in the foreground, press once
for edit mode and twice to cancel the Timer. If the desired
Timer is not in the foreground, follow the steps below.
1. Press the desired TIMER pad once.The selected Timer will
come to the foreground.
2. Press the TIMER pad a secondtime to access the edit
mode in order to make changes.
3. Pressing the TIMER pad a thirdtime will cancel the Timer.
Changing the Timer beeps:
The signal beeps for TIMER 1 and TIMER 2 can be changed.
The options available are two beeps every thirty seconds, two
beeps every sixty seconds or one beep only. The default
setting is one beep.
1. Press the Setup pad.
2. Select the arrow to scroll until TONES
is displayed.
3. Select TONES.
z ..... -
/Setup
On/Off/
,/
\/
4. Select TIMERS TONES.
5. Select the desired timer beep format [2-30 SEC,2-60 SEC
or 1 BEEP).
6. Press Setup pad to exit Setup mode.
Locking the Control and Oven Door
The oven control and oven door can be locked to prevent
accidental programming. If an oven function is currently
being used, the control and door cannot be locked.
To lock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds or until CONTROL LOCKED appears in the
display.
To unlock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds. UNLOCKING DOORwill appear in the display
when the control and door are unlocking.
Back 0 Enter
[ s2 l

Baking
To set Bake: _.................
1. Press the Bake pad. _ Bake
2. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
• The temperature can be set from 170° Fto 550° F
in 5° increments.
•After three seconds, the oven will begin to preheat.
BAKE and PREHEATwill appear in the display along
with 100° or the actual oven temperature, whichever
is higher.
• The temperature in the display will increase in 1°
increments until the oven reaches the preset
temperature. Allow about 15 minutes for the oven
to preheat.
• When the oven is preheated, the oven will beep and
PREHEATwill no longer be displayed.
3. At the end of cooking, turn the oven off by ,,.................
pressing the CANCEL pad. Removefood CANCEL i:
from the oven. The oven will continue .................................
operating until the CANCEL pad is pressed.
Notes:
• If more than thirty seconds elapse between pressing a
pad and pressing a number pad, the display will return
to the previous display.
• Whenever the temperature appears in the display, the
oven is heating.
• To change the oven temperature during cooking, press
the Bake pad and select a displayed temperature or use
the number pads to enter the desired temperature.
•The oven will automatically shut off after 12 hours if it is
accidentally left on. To set a Sabbath Mode, see Sabbath
Mode, page 28.
When using Delay, the oven begins to cook later in the day.
Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time. When that time has elapsed, the oven will keep the food
warm for up to an hour then automatically turn off.
To set Cook & Hold (select models:):
1. After Bake has been programmed, press /More
the More Options pad. ODtions __ b
2. Select COOK/HLD. ...............
3. Select the amount of time you want to bake by pressing
the Quickset pads or the number pads.
4. Pressthe Enter pad.
5. COOK TIME, the cook time countdown, PREHEAT,BAKE
and the actual temperature will be displayed.
The oven will cook for the selected time, then keep food warm
for one hour.
To set a Delay:
1. After Bake has been programmed, press
the More Options pad.
2. Select DELAY.
3.
4.
5.
6.
/More
Options /
Select the amount of time you want to delay the start of
cooking using the displayed times or the number pads.
Select the amount of time you want to cook using the
displayed times or the number pads.
The display will show BAKE,the temperature, the delay
time and the cook time countdown.
When the delay time has expired, the oven will begin
heating. COOKTIME, the cook time countdown, PREHEAT,
BAKE and the actual oven temperature will be displayed.
Bake Options
Cook & Hold (select models:)and Delay options are available
when baking. When using the Cook & Hold option (select
models:),the oven begins to heat immediately after the control
has been set. Then, the oven cooks for a specified length of
time. When that time has elapsed, the oven will automatically
reduce temperature to 170° F,keep the food warm for up to
an hour and then automatically turn off.
15

Convect [selectmodels)
Convectionusesa fantocirculatehotairevenlyover,under
and aroundthefood.As a result,foodsareevenlycooked
and browned,ofteninshortertimes,atlowertemperatures
and withtheflexibilityofusingmorethanone rackata time.
Notes:
, The oven control comes from the factory set for Auto
Convect Conversion. When using Convect Bake and
Convect Pastryenter the conventionalbaking
temperature. The control automatically converts the
temperature to 25° less than the conventional
temperature.
• When using Convect Roast the temperature will not be
automatically reduced. Enter the conventional roasting
temperature and time. The control then lets you know
when 750/0of the time has elapsed and alerts you to
check the food for doneness.
° To turn Auto Convect Conversion off, see page 27.
Convect Options
Cook & Hold and Delay options are available when convect
cooking. See page 15 for informationon how to program a
Cook & Hold or Delay option.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Multiple-Rack
Baking of
Cookies/Biscuits
Breads
Casseroles
Tarts/Tortes
Cakes
Whole Chicken
Whole Turkey
Vegetables
PorkRoasts
BeefRoasts
FrozenPie
Turnovers
Cream Puffs
Puff Pastry
Oo[|veot Bake (select models)
To set Convect Bake: Convect :
1. Press the Convect pad.
2. Select CNVT BAKE using the Quickset pads.
3. Select the oven temperature using the Quickset pads
° The temperature can be set from 195° Fto 550° F
degrees in 5° increments. If Auto Convect is off,
temperature can be set from 170°.
• After three seconds, the oven will begin to preheat.
CNVT BAKE and PREHEATwill appear in the display
along with 100° or the actual oven temperature,
whichever is higher.
° The temperature in the display will increase in 1°
increments until the oven reaches the preset
temperature. Allow about 15 minutes for the oven
to preheat.
• When the oven is preheated, the oven will beep,
PREHEATwill turn off and CNVT BAKE will be displayed.
AUTO will be displayed if Auto Convect Conversion
feature is turned on.
• Placefood in the oven. ,,................
(\
4. At the end of cooking, turn the oven off by CANCEL
pressing the CANCEL pad. Remove food
from the oven. The oven will continue operating until the
CANCEL pad is pressed.
Rapid Preheat (selectmodels)
Use to decrease preheating time when using Bake or Convect
Bake. Use for all foods when baking on one rack.
• After Bake or Convect Bake has been programmed and
activated, press the Rapid Preheat pad.
• 1 RACK ONLY will display, after 10 seconds the display will
show RAPIDand PREHEAT.
To return to Standard Preheat:
• Press Rapid Preheat pad again. This will provide standard
preheat and PREHEATand the selected function will be
displayed.
Notes:
° For best results, use rack position 2 or 3 when using the
Rapid Preheat option.
• For optimum baking and browning results, Rapid Preheat
is not recommended when baking on multiple racks.
Oo[|vect Roast (select models)
To set Convect Roast:
1. Placefood in the oven.
2. Pressthe Convect pad.
3. Select CNVT ROAST using the
Quickset pads.
/f ........................ ""x
Convect )
OR
Enter the desired temperature using the number pads.
Press Enter pad to set. Cant.
16

4. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
• The temperature can be set from 170° Fto 550° F
degrees in 5° increments.
5. Enter desired cook time. Enter the conventional roasting
time using the number pads.
• After three seconds, the oven will begin to heat. CNVT
ROASTwill appear in the display along with 100° or the
actual oven temperature, whichever is higher.
° The temperature in the display will increase in 1°
increments until the oven reaches the preset
temperature.
° Cook time will begin to count down.
6. At 750/0of the cooking time the oven will beep to let
you know to check food. Check food using a meat
thermometer. If food is done, take food out of oven and
press CANCEL pad to turn oven off.
7. If food is not done, continue roasting.
Once the set time has elapsed the oven will automatically
go into Keep Warm mode for 1 hour and then shut off. If
food is taken from the oven before the /....................,
hour has elapsed, press the CANCEL pad. ( CANCEL
" ................................ Y
Notes:
° if the recipe suggests preheating the oven, add 15
minutes to cook time.
° If Auto Convect is off, roast time will not be required.
Convect Pastry (selectmodels)
Convect Pastry isdesigned to bake pastry itemssuch as
frozen pies, turnovers, cream puffs and puff pastry. Use one,
two or three racks while using this feature.
j ..............................
1. Pressthe Convect pad. CORVeC[
2. Select CNVT PASTRY using the ..................................
Quickset pads.
3. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
° The temperature can be set from 195° Fto 550° F
degrees in 5° increments.
• After three seconds, the oven will begin to preheat.
CNVT PASTRYand PREHEATwill appear in the display
along with 100° or the actual oven temperature, which
ever is higher. AUTO will display if the Auto Convect
Conversion feature is turned on.
° The temperature in the display will increase in 1°
increments until the oven reaches the preset
temperature. Allow about 15 minutes for the oven to
preheat.
• When the oven is preheated, the oven will beep,
PREHEATwill turn off and CNVT PASTRYwill be
displayed.
4. At the end of cooking, turn the oven off by /............. ,
pressing the CANCEL pad. Remove food 'ICANCEL i
from the oven. The oven will continue ......... /
operating until the CANCEL pad is pressed.
17

WaF rliRg [}rawer (seleotmodels]
The Warming Drawerisusedforkeepinghotfoodsatsewing
temperature.Itmay alsobe usedforwarmingbreadsand
pastries.
Operating the Controls:
1. If using the rack, position itwhere needed.
2. Pressthe Warm Drawer pad to turn on.
3. Select HiGH or LOW.
J"Warm...........
Drawer
On/Off
.......... J
4. Allow the drawer to preheat for ten minutes.
5. Placefood in warming drawer.
6. When finished, press the Warm Drawer pad to turn off.
Removefood from the drawer.
Broil
For optimal results, preheat for five minutes with the door
closed and use a pan designed for broiling. Oven door should
be open to the broil stop position (about 4 inches] when
broiling.
To set Broil:
1. Placethe oven rack in the proper rack position (see
Broiling Chart, page 19].
2. Pressthe Broil pad. , Broil
3. Select HIGH - 550° Ffor high broil. ..............
OR
Select LOW - 450° Ffor low broil.
Warming Chart
HIGH Bacon Beef - Rare
Casseroles Cooked Cereals
Dinner Plate Eggs
Enchiladas Fish/Seafood
Fried Food Gravy, Cream Sauces
Ham Hamburger Patties
Hors d'oeuvres Lamb
Pancakes Pizza
Pork Potatoes - Baked
Potatoes - Mashed Poultry
Vegetables Waffles
LOW Biscuits Coffee Cake
Pies Warming - Plates
Notes:
•Do not warm food for more than one hour (eggs
30 minutes] after cooking.
•Food must be at serving temperature before being
placed in the drawer.
•Breads, pastries and fruit pies may be warmed from
room temperature at the HIGH setting.
• Use only oven-safe cookware.
°Remove food from plastic bags and place in oven-safe
cookware.
°Serving dishes and plates can be warmed while
preheating the drawer.
• Cover food with a lid or aluminum foil. Do not use
plastic wrap. (Fried foods do not need to be covered.]
4,
5.
• The oven has a variable broil feature which means that
a lower broil temperature can be selected (3000-550° F].
To select a lower temperature, press the appropriate
number pads. Press Enter pad to set the lower
temperature.
Preheat the oven for five minutes.
Placefood in the oven and close the door to the broil stop
position.
Pressthe CANCEL pad when broiling CANCEL :
is done. , ,,
Notes:
• See Broiling Chart, page 19,for foods and broiling times.
° If more than 30 seconds elapse between pressing the
Broil pad, Quickset pads, or number pads, the oven will
not be set and the display will return to the previous
display.
• HIGH is used for most broiling. Use a lower broil
temperature when broiling longer-cooking foods. The
lower temperature allows food to cook to the well done
stage without excessive browning.
• Expect broil times to increase and browning to be
slightly lighter if the appliance is installed on a 208 volt
circuit.
° Food should be turned halfway through broiling time.
• Broil times may be longer when lower broiling
temperatures are selected.
Cont.
18

Broiling Chart iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ii i i i! !ii!i!iiii ii!ii!iiii!ii! iii!ii!i ii!!! ! i i!i !i!! !i i !i! iiiiiiiii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!i!!! !!i!i!i!ii iii!i
i Beef (broiled to 165 ° F)
6 Hamburgers, 1/2" thick
2 Ribeye Steaks, 1" thick
2 New York Strip Steaks, 1" thick
2 T-Bone Steaks, 1" thick
Poultry (broiled to 170° Fon Low)
4 Boneless/Skinless Breasts
4 Bone-In Chicken Breasts
Pork (broiled to 160° F)
4 Boneless Pork Chops, 1"thick
4 Bone-In Pork Chops, 1" thick
Ham Slice, 1" thick
Fish (broiled to 140° F)
4 Swordfish Steaks, 1" thick
2 Halibut Steaks, 1" thick
Orange Roughy, 1 "thick
Shrimp (16-20 ct. per lb.)
2 Salmon Fillets, 1/2" thick
2 Salmon Steaks, 1" thick
10 - 12 minutes
18 - 22 minutes
18 - 22 minutes
18 - 22 minutes
Low Broil
12 - 15 minutes
20 - 33 minutes
20 - 28 minutes
25 - 28 minutes
12 - 16 minutes
10 - 14 minutes
10 - 14 minutes
10 - 12 minutes
8 - 10 minutes
8 - 12 minutes
10 - 14 minutes
4
4
4
4
4
3
4
4
4
3
3
4
4
4
3
*Note: To reduce browning and excess smoke when broiling, use a lower rack position and increase the
broil time.
19