Jensen JEN99BT3BCF4 User manual

128-7054
1 of 8
The transmitters included with the system have been pre-programmed at the
factory, with each button pre-assigned to control a specific function of the
system. Although the system in the vehicle has either a 3, 4, or 5 channel
RECEIVER,dependingonthemodel,thetransmittersincludedwiththesystem
are 7 channel transmitters. This allows you to program each transmitter to
morethanonevehicleintwocarfamiliesandalsoallowsyouto change which
button or buttons control certain functions of the system.
( Example: Transmitter channel 5, shown below, can be programmed to
activate Receiver channel 2.) Refer to the chart below for access to each of
the transmitter channels, and for the standard factory button assignments.
Transmitter Programming Guide
Model : JEN99BT3BCF4
& JEN99BT3SBCF4
1 1 Remote Arm & Disarm
*Remote Emergency Panic
*Remote Door Lock & Unlock
2 OPT. 1 3 Push And Hold For 3 Seconds For Opt1
Release, Push 2 Times For Aux. Out.
3 OPT. 2 4 ** Pulsed Output for Accessories
4 5 ** Switched Output for Accessories
5--
6--
7--
TRANSMITTER SYSTEM RECEIVER
CHANNEL BUTTONS CHANNEL FUNCTION
&
&
&
& &
* Remote Emergency Panic is available only on certain models.
* Door Lock/Unlock may require additional components in certain vehicles.
** Some of the more common accessories for these additional channels are;
AS 9075 Remote Car Starter
AS 9256 Remote Trunk Release Relay
AS 9154 Remote Garage Door Interface
AS 9153 Remote Window Roll Up

128-7054
2 of 8
PROGRAMMINGTRANSMITTERS:
It is important to remember that during programming, each individual step of
theproceduremustbeexecutedwithin15secondsofthepreviousstep. When
the 15 second time limit is allowed to expire, the system will automatically exit
program mode. This is indicated by a long "chirp" from the siren.
Additionally, any time the ignition key is turned off while programming, the
system will immediately exit program mode. This is also indicated by a long
"chirp" from the siren.
TOPROGRAMADDITIONALTRANSMITTERS:
NOTE: The programming information described below assumes that the
defaulttransmitterisbeingusedandtheLock/Unlockbuttonisoneand
the same. If you have the optional transmitter with a separate Lock
and Unlock button, use letter "B" reference below for programming.
Also, where indicated that the siren will emit a long chirp tone, the
optional horn may be connected, in which case either or both the horn
and siren may sound.
1. (a) Enter the vehicle, and turn the ignition key to the "on" position.
(b) Enter the vehicle, and turn the ignition key to the "on" position.
2. (a) Press and release the valet/bypass push button switch 3 times.
(b) Press and release the valet/bypass push button switch 3 times.
3. (a) The dash LED will flash one time and the siren will "chirp" 1 time
indicating the system is ready to accept programming for channel
1, Arm/Disarm, Lock/Unlock and Panic.
(b) The dash LED will flash one time and the siren will "chirp" 1 time
indicating the system is ready to accept programming for channel
1, Arm/Lock and Panic.
4. (a) You can assign the Lock/Unlock, Arm/Disarm button, by pressing
and holding the lock/unlock button until the siren emits a long chirp
tone. The chirp tone confirms that programming of channel 1 was
successful.
Up to 4 transmitters can be programmed, press and hold the selected button
ofeach additionaltransmitteruntil thechirptone isheard,orpressandrelease
the valet push-button switch two times to advance to step #8.
(b) You can assign the Lock/Arm button by pressing and holding the
lock button until the siren emits a long chirp tone.
2

128-7054
3 of 8
Thechirptoneconfirmsthat programming of channel 1 was success
ful. Up to 4 transmitters can be programmed, press and hold the
selected button of each additional transmitter until the chirp tone is
heard, or move to step #5
5. Press and release the valet/override switch one time to advance to
channel 2.
6. (a) Disregard this step.
(b) The dash mounted LED will flash 2 times, and the siren will "chirp"
2timesindicatingthat thesystemisreadytoacceptprogrammingfor
channel 2. Unlock/2nd Unlock, Disarm, and Panic. Press and hold
the Unlock button on your keychain transmitter until the siren emits
a long chirp tone. This confirms that programming of channel 2 was
successful.Up to 4 transmitters can beprogrammed, press and hold
the selected button of each additional transmitter until the chirp tone
is heard.
7. Press and release the valet/override switch one time to advance to channel
3.
8. The dash mounted LED will flash 3 times, and the siren will "chirp" 3
times, indicating that the system is ready to accept programming for
channel 3. Trunk Release Output, (where so equipped), or alternate
channel output when used.
9. (a) Press and hold the 1st Opt. button on your keychain transmitter until
the siren emits a long chirp tone. This confirms that programming of
channel 3 was successful. Up to 4 transmitters can be programmed,
pressandholdtheselectedbuttonofeachadditionaltransmitteruntil
the chirp tone is heard.
(b) Press and hold the Opt. button on your keychain transmitter until the
siren emits a long chirp tone. This confirms that programming of
channel 3 was successful. Up to 4 transmitters can be programmed,
pressandholdtheselectedbuttonofeachadditionaltransmitteruntil
the chirp tone is heard.
10. Press and release the valet/override switch one time to advance to channel
4 if so equipped. If your system does not have a 4th channel, a long chirp
followed by a short chirp tone will indicate that the program mode has been
exited.
11. The dash mounted LED will flash 4 times, and siren will "chirp" 4 times
indicating that the system is ready to accept programming of channel 4.
3

128-7054
4 of 8
Afterthedesiredchannelisprogrammed,turntheignitionkeytotheoffposition
to exit programming mode.
12. (a) Press and hold the remaining Opt. button of the transmitter until
the siren emits a long chirp tone. This confirms that programming
of channel 4 was successful. Up to 4 transmitters can be
programmed, press and hold the selected button of each addi-
tional transmitter until the chirp tone is heard.
(b) Press and hold any combination of two buttons simultaneously,
until the siren emits a long chirp tone. This confirms that program
ming of channel 4 was successful. Up to 4 transmitters can be
programmed, press and hold the selected button of each addi-
tionaltransmitteruntilthechirptoneis heard,orpressandrelease
the push button switch to exit the programming mode, or turn the
ignition switch off to exit the programming mode.
Thesirenemitsalongfollowedbyashortchirptoneindicatingthat
the program mode has been exited.
NOTE: If programming to a Keyless Entry (non alarm) unit, there
will be NO chirp indication.
QUICKREFERENCE:
You can program any individual channel, without reprogramming all channels,
by following the quick reference chart below. (Not All Units Have 4 Channels)
4
CHANNEL VALET SWITCH
Press and Release 3 Times
Press and Release 4 Times
Press and Release 5 Times
Press and Release 6 Times
LED
1
2
3
4
1 Flash
2 Flashes
3 Flashes
4 Flashes

128-7054
5 of 8
BATTERY REPLACEMENT:
Thetransmitterincorporatesa small red LED built intothecase.ThisLEDcan
be usedtoindicatebattery condition. Youwillnoticeadecreaseintransmitter
range as the battery condition deteriorates. To replace the battery...
1. Removethetransmittercoverbyremovingthesmallscrewfromtheback
of the transmitter case.
2. Remove the discharged battery, making note of the orientation of the
+ and -contacts, and dispose of properly.
3. Install the new (type GP23A) battery, taking care to orient the + and -
contacts properly.
4. Replace the transmitter cover, taking care not to damage the LED or
switches on the circuit board.
5

128-7054
6 of 8
IMPORTANT: To help us expedite your order, please print all of the information legibly,
and mail this form and your payment according to the instructions below. Please indicate
which button pad is used with your transmitter as indicated above. __________
Please indicate transmitter model number as found on back of case. ________
1.Name :______________________________________________________
Address:_____________________________________________________
City: ___________________ State : ________ Zip Code :______________
2. TelephoneNumber:(__________)________________________________
3. Enterthetotalnumberoftransmittersrequiredhere:____________________
4. The cost per transmitter is $ 65.00.
5. Enterthetotalamountenclosedhere:_______________________________
( New York state residents must include the appropriate sales tax. )
6. Method of payment; check one of the boxes below.
GMastercard GVisa GCheck or money order * (do not send cash)
* Make checks payable to Audiovox Corporation
7. CreditCardNumber:___________________________________________
8. Credit Card Expiration Date : __________________________
9. Mail this form, and your check, to ;
Credit card purchasers can order additional or replacement
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and
follow the instructions from the operator interface.

Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788
Attn.: TRANSMITTER DEPARTMENT
PD 30 PD 31 PD 33 PD 34
ORDER FORM FOR JEN99BT3BCF4 & JEN99BT3SBCF4
TRANSMITTER
6

128-7054
7 of 8
THISPAGELEFTBLANKINTENTIONALLY

128-7054
8 of 8
©2004 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788
128-7054