Jet Jovs-10 Service manual

Operating Instructions and Parts Manual

Oscillating Spindle Sander

Model JOVS-10

WALTER MEIER (Manufacturing) Inc.

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-708411

Ph.: 800-274-6848 Revision A 04/2010

Warranty and Service

Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of

our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any

of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or

perform routine maintenance and major repair on your JET

tools. For the name of an Authorized Service Center in

your area call 1-800-274-6848.

MORE INFORMATION

Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with

your local Walter Meier distributor, or visit waltermeier.com.

WARRANTY

JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW =

Woodworking).

WHAT IS COVERED?

This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools,

abrasives and other consumables are excluded from warranty coverage.

WHO IS COVERED?

This warranty covers only the initial purchaser of the product.

WHAT IS THE PERIOD OF COVERAGE?

The general JET warranty lasts for the time period specified in the product literature of each product.

WHAT IS NOT COVERED?

Five Year Warranties do not cover woodworking (WW) products used for commercial, industrial or educational

purposes. Woodworking products with Five Year Warranties that are used for commercial, industrial or education

purposes revert to a One Year Warranty. This warranty does not cover defects due directly or indirectly to misuse,

abuse, negligence or accidents, normal wear-and-tear, improper repair or alterations, or lack of maintenance.

HOW TO GET SERVICE

The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name

of the location nearest you, please call 1-800-274-6848.

You must provide proof of initial purchase date and an explanation of the complaint must accompany the

merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price,

at our option. We will return the repaired product or replacement at our expense unless it is determined by us that

there is no defect, or that the defect resulted from causes not within the scope of our warranty in which case we will,

at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be

responsible for the shipping and handling costs of the return.

HOW STATE LAW APPLIES

This warranty gives you specific legal rights; you may also have other rights which vary from state to state.

LIMITATIONS ON THIS WARRANTY

WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE

LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR

MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR

FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF

OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are given as general

information and are not binding. Members of Walter Meier reserve the right to effect at any time, without prior notice,

those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason

whatsoever. JET

branded products are not sold in Canada by Walter Meier.

Table of Contents

Warranty and Service..........................................................................................................................2

Table of Contents ...............................................................................................................................3

Warning .............................................................................................................................................4

Grounding Instructions ........................................................................................................................6

Introduction ........................................................................................................................................7

Specifications .....................................................................................................................................7

Unpacking..........................................................................................................................................8

Contents of the Shipping Container ..................................................................................................8

Mounting Sanding Sleeves...............................................................................................................9

Installing Sanding Assemblies ..........................................................................................................9

Removing Sanding Assemblies ........................................................................................................9

Table Insert...................................................................................................................................10

Sanding Assembly 90° to Table......................................................................................................10

Replacing Sanding Sleeve .............................................................................................................11

Dust Collection .................................................................................................................................11

Maintenance ....................................................................................................................................11

Replacement Parts ...........................................................................................................................12

Breakdown for the JOVS-10 Oscillating Spindle Sander ...................................................................13

Parts List for the JOVS-10 Oscillating Spindle Sander......................................................................14

Sanding Assemblies ......................................................................................................................16

Sanding Assemblies ......................................................................................................................17

Electrical Connections.......................................................................................................................18

Warning

Wear eye protection.

Always keep guards in place and in proper operating condition. Do not operate the machine

without the guards for any reason.

This sander is intended to be used with wood and wood products only. Use of this sander and a

dust collector with metal products is a potential fire hazard.

Support the workpiece adequately at all times during operation; maintain control of the work

at all times.

•REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and

adjusting wrenches are removed from the machine before turning it on.

•KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.

•DON’T USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations,

or expose them to rain. Keep work area well lighted.

•KEEP CHILDREN AWAY. All visitors should be kept a safe distance from the work area.

•MAKE THE WORKSHOP KIDPROOF with padlocks, master swatches, or by removing starter keys.

•DON’T FORCE THE MACHINE. It will do the job better and safer at the rate for which it was

designed.

•USE THE RIGHT TOOL. Don’t force a machine or attachment to do a job for which it was not

designed.

•USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When

using an extension cord, be sure to use one heavy enough to carry the current your machine will

draw. An undersized cord will cause a drop in the line voltage resulting in power loss and

overheating. The table following shows the correct size to use depending on the cord length and

nameplate ampere rating. If in doubt, use the next heavier gauge. Remember, the smaller the gauge

number, the heavier the cord.

olts Total Length of Cord in Feet

120V 25 ft. 50 ft.

AWG

16 14

•WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other

jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective

hair covering to contain long hair.

•ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is dusty.

Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

•DON’T OVERREACH. Keep proper footing and balance at all times.

•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories.

•ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING.

•REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position

before plugging in.

•USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not

recommended by JET may cause hazards or risk of injury to persons.

•NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped.

•CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is

damaged should be carefully checked to determine that it will operate properly and perform its

intended function - check for alignment of moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its operation. A guard or other part that is

damaged should be properly repaired or replaced.

•NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN POWER OFF. Don’t leave the

machine until it comes to a complete stop.

•SOME DUST CREATED by power sanding, sawing, grinding, drilling and other construction activities

contains chemicals known to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

•Lead from lead based paint

•Crystalline silica from bricks and cement and other masonry products, and

•Arsenic and chromium from chemically-treated lumber.

Your risk from those exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specifically designed to filter out microscopic particles

•DO NOT operate tool while under the influence of drugs, alcohol or any medication.

•AVOID kickback by sanding in accordance with directional arrows.

•DO NOT sand pieces of material that are too small to be safely supported.

•WHEN sanding a large workpiece, provide additional support at table height.

•ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available

from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident

Prevention Manual for Industrial Operations and also in the safety Data Sheets provided by the NSC.

Please also refer to the American National Standards Institute ANSI 01.1 Safety Requirements for

Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.

•SAVE THESE INSTRUCTIONS Refer to them often and use them to instruct others.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious or even fatal

injury.

Grounding Instructions

Caution: This tool must be grounded while in use to protect the operator from electric shock.

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric

current to reduce the risk of electric shock. This tool is equipped with an electric cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet

that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified

electrician.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The

conductor, with insulation having an outer surface that is green with or without yellow stripes, is the

equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not

connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely

understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension

cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug.

Repair or replace a damaged or worn cord immediately.

115 Volt Operation

As received from the factory, your sander is ready to run at 115 volt operation. This sander, when wired

for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated

in (A). A temporary adapter, which looks like the adapter as illustrated in (B), may be used to connect

this plug to a two-pole receptacle, as shown in (B) if a properly grounded outlet is not available. The

temporary adapter should only be used until a properly grounded outlet can be installed by a qualified

electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug, or tab,

extending from the adapter, must be connected to a permanent ground such as a properly grounded

outlet box, as shown in (B).

Introduction

This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and

maintenance procedures for a JET Model JOVS-10 Oscillating Spindle Sander. This manual contains

instructions on installation, safety precautions, general operating procedures, maintenance instructions

and parts breakdown. This machine has been designed and constructed to provide years of trouble free

operation if used in accordance with instructions set forth in this manual. If there are any questions or

comments, please contact either your local supplier or Walter Meier. Walter Meier can also be reached at

our web site: www.waltermeier.com.

Specifications

Model Number........................................................................................................................ JOVS-10

Stock Number .......................................................................................................................... 708411

Table Size (in.) ..........................................................................................................................24 x 24

Table Tilt (deg.) .......................................................................................................................45 down

Dust Port Diameter (in.).......................................................................................................................4

Spindle Speed (RPM) .................................................................................................................. 1,725

Oscillations Per Minute .....................................................................................................................75

Length of Oscillation (in.)............................................................................................................... 1-1/2

Motor...............................................................................................TEFC, 1HP, 1Ph, 115V Only, 60Hz

Overall Dimensions (LxWxH)(in.) ........................................................................................ 26 x 26 x 42

Net Weight, approximate (lbs.)......................................................................................................... 298

The above specifications were current at the time this manual was published, but because of our policy of

continuous improvement, Walter Meier reserves the right to change specifications at any time and without

prior notice, without incurring obligations.

Unpacking

Contents of the Shipping Container

1 Sander

3 Table Insert Rings

2 Spindle Wrenches

1 2mm Hex Wrench

10 Removable Spindles

1/4” x 5” Steel and Sanding Sleeve

3/8” x 6” Steel and Sanding Sleeve

1/2” x 6” Steel and Sanding Sleeve

5/8” x 6” Steel and Sanding Sleeve

3/4” x 9” Steel and Sanding Sleeve

1” x 9” Rubber and Sanding Sleeve

1-1/2” x 9” Rubber and Sanding Sleeve

2” x 9” Rubber and Sanding Sleeve

3” x 9” Rubber and Sanding Sleeve

4” x 9” Rubber and Sanding Sleeve

1 Owner's Manual

1 Warranty Card

Tools Required for Assembly and

Adjustments

1 26mm Wrench or Large Adjustable Wrench

1 6mm Hex Wrench

1 Square

Read and understand the

entire contents of this manual before

attempting assembly or operation of the

sander. Failure to comply may cause serious

injury.

1. Remove all contents from shipping carton.

2. Report any damage to your distributor.

3. Do not discard any shipping material until

the sander has been assembled and is

running properly.

4. With help from another person move the

sander off of the pallet and into the desired

position.

5. Remove the protective coating found on the

table using a soft rag and a cleaning solvent

that will not damage painted surfaces.

Note: Now is a perfect time to set your sander

up on a mobile base. It will make life easier in

the woodshop. A JET Heavy Duty Universal

Mobile Base is available to fit this sander. JET

also has a variety of Dust Collectors and Air

Filtration Units that will work nicely with your

new sander. Visit waltermeier.com or contact

your JET distributor for options.

Mounting Sanding Sleeves

1. Thoroughly clean the arbors (A, Figure 1) on

all of the spindle assemblies. Also clean the

arbor housing on the sander.

2. Slip the sanding sleeve (B, Figure 1) over

the spindle and hold in place by tightening

the set screw (C, Figure 1) with the supplied

2mm hex wrench.

3. Repeat for all of the steel spindle

assemblies.

4. To protect the sanding assemblies place

them in the holders found on the sides of

the sander. See Figure 2.

Installing Sanding Assemblies

Disconnect the sander from

the power source when installing or

removing sanding assemblies. Failure to

comply may cause serious injury.

1. Thoroughly clean the arbor and arbor

housing before installing the sanding

assemblies.

2. Thread the arbor (A, Figure 3) into the arbor

housing (B, Figure 3).

3. Use the provided wrenches to hold the

lower arbor housing nut (C, Figure 3) while

turning the arbor nut (D, Figure 3)

clockwise.

Removing Sanding Assemblies

1. Disconnect the sander from the power

source, unplug.

2. Use the provided wrenches to hold the

upper arbor housing nut (E, Figure 3) while

turning the arbor nut (D, Figure 3) counter-

clockwise.

Figure 1

Figure 2

Figure 3

Table Insert

1. Disconnect the sander from the power

source, unplug.

2. Choose the insert (A, Figure 4) that most

closely matches the diameter of the sanding

drum.

3. Line up the notch in t he insert with the

spring pin in the table (B, Figure 4), and

press in place.

4. Remove the insert by pressing up from

underneath. Note: Keep the opening in the

table clean so that the insert can be easily

put in place, and removed.

Sanding Assembly 90° to Table

1. Loosen the lock knobs (C, Figure 5) on the

trunnions and position the table so that it

rests against the 90° stop (D, Figure 6

)

Tighten lock knobs.

2. Place a square (E, Figure 5) on the working

side of the table, and make sure the sanding

drum is perpendicular to the table.

3. If an adjustment needs to be made loosen

the hex nut (F, Figure 6).

4. Loosen lock knobs.

5. Rotate the 90° stop in the appropriate

direction until the table rests 90° to the

sanding drum.

6. Tighten the hex nut while holding the stop.

7. Adjust pointer (G, Figure 6) so that it

indicates the “0” position on the scale.

Figure 4

Figure 5

Figure 6

Replacing Sanding Sleeve

1. Loosen hex nut (A, Figure 7) with a 26mm

wrench, or large adjustable wrench.

2. Slide the sanding sleeve (B, Figure 7) off

the drum and replace with a new sanding

sleeve. Note: If the sanding sleeve is not

easily removed, cut the sleeve off and clea n

the drum before reinstalling a new sleeve.

3. If you are replacing the sanding sleeves on

the steel spindles, loosen the set screw

found on the arbor nut.

4. Remove sanding sleeve from the spindle

and replace with a new sandin

sleeve.

Note: If the sanding sleeve is not easily

removed, cut the sleeve off and clean the

drum before reinstalling a new sleeve.

5. Tighten the set screw.

Dust Collection

In order to collect wood dust, attach a dust

collection hose to the dust port. A variety of JET

dust collectors, air filtration units, hoses and

adaptors, etc. are available that will work

effectively with y our new sander. Contact your

local JET Distributor for more information.

Maintenance

The manufacturer recommends replacing the 90

SAE gear lube at 800 hours of use.

1. Open the door on the back side of the

machine to access the drain plug (C, Figure

8). Use a 6mm hex wrench to remove the

drain plug.

2. Refill oil through the oil cap (D, Figure 9

)

The oil capacity is two quarts.

3. The oil sight glass (E, Figure 8) should read

between the “high” and “low” marks.

Keep the machine and all attachments clean.

All bearings are permanently lubricated and

require no further service.

Figure 7

Figure 8

Figure 9

Troubleshooting

Trouble Probable Cause Remedy

Sander will not start.

Sander unplugged from wall or motor. Check all plug connections.

Fuse blown, or circuit breaker tripped

in service panel. Replace fuse, or reset circuit breaker.

Cord damaged. Replace cord.

Starting capacitor bad. Replace starting capacitor.

Sanding drum does

not come up to

speed.

Extension cord too light or too long. Replace with adequate size and

length cord.

Low current. Contact a qualified electrician.

Machine vibrates

excessively. Stand or base on uneven surface. Adjust stand or base so that it rests

evenly on the floor.

Sanded edge not

square. Table not square to sanding drum. Use a square to adjust table to

sanding drum.

Sanding marks on

wood.

Wrong grit sanding sleeve. Use coarser grit for stock removal and

fine grit for finish sanding.

Feed pressure too great. Never force workpiece.

Replacement Parts

Replacement parts are listed on the following pages. To order parts or reach our service department, call

1-800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com).

Having the Model Number and Serial Number of your machine available when you call will allow us to

serve you quickly and accurately.

Breakdown for the JOVS-10 Oscillating Spindle Sander

Parts List for the JOVS-10 Oscillating Spindle Sander

Index No. Part No. Description Size Qty

7.............. OVS10-007 .............Power Cord........................................................................................1

11............ KEY5525.................Key....................................................................................................1

18............ OVS10-18 ...............Oil Indicator........................................................................................1

20............ OS-30628................Oil Seal ..............................................................................................1

21............ BB-6206ZZ..............Ball Bearing......................................................6206ZZ ......................1

22............ OVS10-022 .............C-Ring .............................................................RA63 .........................1

22A.......... OVS10-022A ...........C-Ring .............................................................RA62 .........................1

26............ OVS10-026 .............Sleeve ...............................................................................................1

27............ OVS10-027 .............Guide Rail Shaft .................................................................................1

28............ BB-6205ZZ..............Ball Bearing......................................................6205LU......................2

29............ OVS10-029 .............Locking Nut ........................................................................................1

30............ OVS10-030 .............Worm.................................................................................................1

31............ OVS10-031 .............Spring Pin ........................................................5x30 ..........................1

32............ OVS10-032 .............Main Shaft..........................................................................................1

33............ KEY5550.................Key..................................................................5x5x50 .......................1

34............ OVS10-034 .............Set Screw ........................................................M3x12........................2

35............ OVS10-035 .............Spur Gear ..........................................................................................1

36............ OVS10-036 .............Brass Bushing ....................................................................................2

37............ TS-0208061 ............Socket Head Cap Screw ...................................5/16”-18x1”............... 16

38............ OVS10-038 .............Transmission Rod Shaft ......................................................................2

39............ OVS10-039 .............Transmission Rod...............................................................................2

40............ TS-0640091 ............Hex Nut, Nylon Lock .........................................3/8”-16.......................4

47............ OVS10-047 .............Switch Cord........................................................................................1

52............ OVS10-052 .............Locking Nut ......................................................5/8”-11.......................1

55............ OVS10-055 .............Rear Trunnion Bracket ........................................................................2

56............ TS-0208082 ............Socket Head Cap Screw ...................................5/16”-24x1-1/2”......... 10

64............ OVS10-064 .............Oil Lid ................................................................................................1

66............ OVS10-066 .............Hex Socket Cap Screw .....................................3/8”-16x3/4”................4

67............ TS-0680042 ............Flat Washer......................................................3/8”............................8

86............ OVS10-086 .............Angle Pointer......................................................................................1

87............ OVS10-087 .............Pan Head Machine Screw .................................10-24x1/4”..................1

88............ OVS10-088 .............Cap ...................................................................................................1

89............ OVS10-089 .............Nut ..................................................................15/16”-24 R.H.............2

134 .......... JOVS10-134............Oil Plug ............................................................PT1/4”........................1

135 .......... JOVS10-135............Brass Bushing Bracket........................................................................1

136 .......... JOVS10-136............Shaft Brass Bushing ...........................................................................4

137 .......... JOVS10-137............Knob................................................................5/16”-18x3/4”..............1

139 .......... JOVS10-139W.........Bracket Base......................................................................................2

140 .......... TS-0680032 ............Flat Washer......................................................5/16” ........................24

141 .......... TS-0051021 ............Cap Screw .......................................................5/16”-18x5/8”..............6

142 .......... JOVS10-142............Switch Box .........................................................................................1

143 .......... JOVS10-143............Pan Head Machine Screw .................................3/16”-24x1-1/2”...........2

143A........ JOVS10-143A .........Hex Nut............................................................3/16”-24 .....................2

144 .......... JOVS10-144W.........Vent Cover .........................................................................................1

145 .......... JOVS10-145W.........Base ..................................................................................................1

146 .......... JOVS10-146............Motor Bracket.....................................................................................1

147 .......... JOVS10-147............Motor.................................................................................................1

................ JOVS10-147MF.......Motor Fan (not shown) ........................................................................1

................ JOVS10-147MFC ....Motor Fan Cover (not shown) ..............................................................1

................ JOVS10-147CC .......Capacitor Cover (not shown) ...............................................................1

................ JOVS10-147RC .......Running Capacitor (not shown)..........................45uf, 250V .................1

................ JOVS10-147SC .......Starting Capacitor (not shown)...........................300MFD, 125VAC.......1

148 .......... JOVS10-148............Strain Relief Bushing ..........................................................................1

149 .......... TS-0720081 ............Lock Washer ....................................................5/16”........................20

151 .......... JOVS10-151............Coupling Head....................................................................................1

152 .......... JOVS10-152............Tank ..................................................................................................1

153 .......... TS-0267041 ............Set Screw ........................................................1/4”-20x3/8”................2

Index No. Part No. Description Size Qty

154 .......... JOVS10-154............Tank Lid.............................................................................................1

155 .......... JOVS10-155............Switch Push Button.............................................................................1

156 .......... JOVS10-156W.........Sanding Assembly Rack .....................................................................2

158 .......... JOVS10-158W.........Rear Trunnion ....................................................................................2

159 .......... JOVS10-159............Locking Knob ...................................................3/8”-16x3/4”................2

160 .......... JOVS10-160W.........Dust Cover .........................................................................................1

161 .......... TS-0051061 ............Hex Bolt ...........................................................5/16”-18x1-1/4”...........2

162 .......... TS-0561021 ............Hex Nut............................................................5/16”-18 .....................6

163 .......... JOVS10-163W.........Working Table ....................................................................................1

164 .......... JOVS10-164............Scale .................................................................................................1

169 .......... JOVS10-169............Fixed Rod ..........................................................................................1

170 .......... TS-0561031 ............Hex Nut............................................................3/8”-16.......................2

171 .......... JOVS10-171............Rubber Feet .......................................................................................4

172 .......... JOVS10-172............Sinking Head Screw..........................................5/16”-18x3/4”..............4

174 .......... JOVS10-174............JET Logo ...........................................................................................1

177 .......... JOVS10-177............Pan Head Screw...............................................3/16”-24x3/8”..............2

178 .......... JOVS10-178............Switch................................................................................................1

179 .......... JOVS10-179............Spring Pin ........................................................3x22 ..........................1

180 .......... JOVS10-180............Fiber Washer....................................................3/8”............................2

181 .......... TS-0720091 ............Lock Washer ....................................................3/8”............................4

182 .......... TS-0271071 ............Set Screw ........................................................3/8”-16x3/4”................1

183 .......... JOVS10-183............Warning Label ....................................................................................1

184 .......... JOVS10-184............I.D Label ............................................................................................1

185 .......... JOVS10-185............Motor Label........................................................................................1

186 .......... JOVS10-186............Rivet ..................................................................................................4

187 .......... TS-0267041 ............Set Screw ........................................................1/4”-20x3/8”................1

188 .......... JOVS10-188............Star Washer .....................................................3/16”..........................2

189 .......... TS-0680011 ............Flat Washer......................................................3/16”..........................1

190 .......... TS-0267021 ............Set Screw ........................................................1/4”-20x1/4”................4

Sanding Assemblies

Index No. Part No. Description Size Qty

93................OVS10-093................. Wrench........................................................................ ........................................ 2

94................OVS10-094A .............. Arbor............................................................................ 3/4” ................................. 6

95................OVS10-095................. Hex Nut ....................................................................... ........................................ 6

96................OVS10-096................. Spring Pin.................................................................... 3.5x25 ............................ 3

97................30105000J..................Spindle Assembly....................................................... 4” .................................... 1

98................OVS10-098................. Washer........................................................................ 4” .................................... 2

99................OVS10-099................. Nut ............................................................................... 3/4”-16” .......................... 6

100 .............575834........................Sanding Sleeve (60 Grit)............................................ 4” .......................................

....................575835........................Sanding Sleeve (80 Grit)............................................ 4” .......................................

....................575836........................Sanding Sleeve (100 Grit) ......................................... 4” .......................................

101 .............30105000I...................Spindle Assembly....................................................... 3” .................................... 1

102 .............575830........................Sanding Sleeve (60 Grit)............................................ 3” .......................................

....................575831........................Sanding Sleeve (80 Grit)............................................ 3” .......................................

....................575832........................Sanding Sleeve (100 Grit) ......................................... 3” .......................................

103 .............OVS10-103................. Washer........................................................................ 3” .................................... 2

104 .............30105000H................. Spindle Assembly....................................................... 2” .................................... 1

105 .............575826........................Sanding Sleeve (60 Grit)............................................ 2” .......................................

....................575827........................Sanding Sleeve (80 Grit)............................................ 2” .......................................

....................575828........................Sanding Sleeve (100 Grit) ......................................... 2” .......................................

106 .............OVS10-106................. Washer........................................................................ 2” .................................... 2

107 .............30105000G................. Spindle Assembly....................................................... 1-1/2”.............................. 1

108 .............575822........................Sanding Sleeve (60 Grit)............................................ 1-1/2”.................................

....................575823........................Sanding Sleeve (80 Grit)............................................ 1-1/2”.................................

....................575824........................Sanding Sleeve (100 Grit) ......................................... 1-1/2”.................................

109 .............OVS10-109.................Washer ........................................................................ 1-1/2”.............................. 2

110 .............30105000F ................. Spindle Assembly ....................................................... 1” .................................... 1

111 .............575818........................Sanding Sleeve (60 Grit)............................................ 1” .......................................

....................575819........................Sanding Sleeve (80 Grit)............................................ 1” .......................................

....................575820........................Sanding Sleeve (100 Grit) ......................................... 1” .......................................

112 .............OVS10-112................. Washer........................................................................ 1” .................................... 2

113 .............575814........................Sanding Sleeve (60 Grit)............................................ 3/4” ....................................

....................575815........................Sanding Sleeve (80 Grit)............................................ 3/4” ....................................

....................575816........................Sanding Sleeve (100 Grit) ......................................... 3/4” ....................................

114 .............OVS10-114A .............. Arbor............................................................................ 5/8” ................................. 1

115 .............OVS10-115.................Hex Nut ....................................................................... 5/8” ................................. 1

118 .............575810........................Sanding Sleeve (60 Grit)............................................ 5/8” ....................................

....................575811........................Sanding Sleeve (80 Grit)............................................ 5/8” ....................................

....................575812........................Sanding Sleeve (100 Grit) ......................................... 5/8” ....................................

....................575813........................Sanding Sleeve (120 Grit) ......................................... 5/8” ....................................

119 .............OVS10-119A .............. Arbor............................................................................ 1/2” ................................. 1

120 .............OVS10-120.................Hex Nut ....................................................................... 1/2” ................................. 1

122 .............575806........................Sanding Sleeve (60 Grit)............................................ 1/2” ....................................

....................575807........................Sanding Sleeve (80 Grit)............................................ 1/2” ....................................

....................575808........................Sanding Sleeve (100 Grit) ......................................... 1/2” ....................................

....................575809........................Sanding Sleeve (120 Grit) ......................................... 1/2” ....................................

124 .............OVS10-124A .............. Arbor............................................................................ 3/8” ................................. 1

125 .............OVS10-125.................Hex Nut ....................................................................... 3/8” ................................. 1

127 .............575802........................Sanding Sleeve (60 Grit)............................................ 3/8” ....................................

....................575803........................Sanding Sleeve (80 Grit)............................................ 3/8” ....................................

....................575804........................Sanding Sleeve (100 Grit) ......................................... 3/8” ....................................

128 .............OVS10-117.................Set Screw.................................................................... 3/16”-24x1/4” ................. 4

129 .............OVS10-129.................Arbor............................................................................ ........................................ 1

130 .............575800........................Sanding Sleeve (100 Grit) ......................................... 1/4” ....................................

....................575801........................Sanding Sleeve (120 Grit) ......................................... 1/4” ....................................

133 .............OVS10-133A .............. Spindle......................................................................... ........................................ 1

165 .............JOVS10-165............... Table Insert (medium)................................................ ........................................ 1

166 .............JOVS10-166............... Table Insert (small)..................................................... ........................................ 1

167 .............JOVS10-167............... Table Insert (Large).................................................... ........................................ 1

191 .............JOVS10-191...............Spring Pin.................................................................... 5x25................................ 6

192 .............JOVS10-192...............Spring Pin.................................................................... 3x25................................ 1